Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

UC3872MTR

Texas Instruments · Other Lighting Drivers · SSOP-16-150mil

UC3872MTR from Texas Instruments, in a SSOP-16-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 BOUT output Push-pull N-channel MOSFET drive output complementary to AOUT, high for 50% of the time and switching states at each zero-detect.
2 AOUT output Push-pull N-channel MOSFET drive output complementary to BOUT, high for 50% of the time and switching states at each zero-detect.
3 VC power_in Power supply for the output drivers (absolute max 24V), to be bypassed to ground with a 0.1µF ceramic capacitor.
4 COMP output Error amplifier output with compensation normally connected between COMP and INV; a capacitor to ground limits turn-on current and blanks open lamp detect.
5 SS passive Soft start pin (20µA source) that limits initial turn-on currents and blanks open lamp detect until soft start completes.
6 N/C unconnected No internal connection.
7 INV input Inverting input of the error amplifier and input to open lamp detect; outputs are disabled if below the 1V open lamp detect threshold.
8 CT passive Timing capacitor to GND sets the synchronization frequency range, charged with approximately 200µA to form the ramp for the buck PWM comparator.
9 ZD input Zero-detect input sensing the transformer primary center tap falling to approximately 0.5V threshold, with a typically 10k series resistor to limit input current.
10 N/C unconnected No internal connection.
11 REF power_out 3V reference voltage for internal logic, to be bypassed to ground with a 0.01µF ceramic capacitor.
12 VCC power_in Positive supply for the chip with operating range 4.2V to 24V, to be bypassed to ground with a 0.1µF ceramic capacitor.
13 ENBL input Enable input, device is enabled when high and shut down drawing typically 1µA when pulled low.
14 COUT output Directly drives the buck regulator P-channel MOSFET at twice the AOUT/BOUT frequency, with smooth control up to 100% duty cycle.
15 PGND power_in High current ground connection for the three output drivers.
16 GND power_in Ground reference for the internal reference and all thresholds.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package SSOP-16-150mil
Category Nixie Tube Driver/LED Driver
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Output Voltage (TJ = 25 C) 2.963 3 3.037 V TJ = 25° C 2
Output Voltage (over temperature) 2.94 3 3.06 V 2
Line Regulation 10 mV VCC = 4.75V to 18V 2
Load Regulation 10 mV IO = 0 to −5mA 2
Free Running Frequency 57 68 78 kHz TJ = 25° C 2
Maximum Synchronization Frequency 160 200 240 kHz TJ = 25° C 2
Charge Current 180 200 220 µA VCT = 1.5V 2
Voltage Stability 2 % 2
Temperature Stability 4 8 % 2
Zero Detect Threshold 0.46 0.5 0.56 V 2
Error Amp Input Voltage 1.445 1.475 1.505 V VO = 2V 2
Error Amp Input Bias Current -0.4 -2 µA 2
Error Amp Open Loop Gain 65 90 dB VO = 0.5 to 3V 2
Error Amp Output High 3.1 3.5 3.9 V VINV = 1.3V 2
Error Amp Output Low 0.1 0.2 V VINV = 1.7V 3
Error Amp Output Source Current -350 -500 µA VINV = 1.3V, VO = 2V 3
Error Amp Output Sink Current 10 20 mA VINV = 1.7V, VO = 2V 3
Error Amp Unity Gain Bandwidth 1 MHz TJ = 25° C (Note 4) 3
Soft Start Threshold 2.9 3.4 3.8 V VINV = 0V 3
Open Lamp Detect Threshold 0.6 1 1.4 V VSS = 4.2V 3
Soft Start Current 10 20 40 µA VSS = 2V 3
Output Low Level (Outputs A and B, IOUT = 0) 0.05 0.2 V IOUT = 0, Outputs A and B 3
Output Low Level (IOUT = 10mA) 0.1 0.4 V IOUT = 10mA 3
Output Low Level (IOUT = 100mA) 1.5 2.2 V IOUT = 100mA 3
Output High Level (Output C, IOUT = 0) 13.9 14.9 V IOUT = 0, Output C 3
Output High Level (Output C, IOUT = -10mA) 13.5 14.3 V IOUT = −10mA 3
Output High Level (Output C, IOUT = -100mA) 12.5 13.5 V IOUT = −100mA 3
Rise Time 30 80 ns TJ = 25° C, Cl = 1nF (Note 4) 3
Fall Time 30 80 ns TJ = 25° C, Cl = 1nF (Note 4) 3
Out A and B Duty Cycle 48 49.9 50 % 3
Out C Max Duty Cycle 100 % VINV = 1V 3
Out C Min Duty Cycle 0 % VINV = 2V 3
UVLO Startup Threshold Voltage 3.7 4.2 4.5 V 3
UVLO Hysteresis 120 200 280 mV 3
Enable Input High Threshold 2 V 3
Enable Input Low Threshold 0.8 V 3
Enable Input Current 150 400 µA VENBL = 5V 3
VCC Supply Current 6 14 mA VCC = 24V 3
VC Supply Current 5 12 mA VC = 24V 3
ICC Disabled 1 10 µA VCC = 24V, VENBL = 0V 3
Analog Inputs -0.3 10 V 2
VCC, VC Voltage 24 V 2
ZD Input Current 10 mA High Impedance Source 2
ZD Input Voltage 24 V Low Impedance Source 2
Power Dissipation 1 W TA = 25° C 2
Storage Temperature -65 150 °C 2
Lead Temperature 300 °C 2
VCC Operating Range VCC 4.2 24 V 4
Operating Junction Temperature (UC3872) TJ 0 70 °C UC3872 2

CAD (KiCad official)

  • Symbol: UC3872MTR
  • Footprint: Package_SO:SSOP-16_3.9x4.9mm_P0.635mm
  • 3D model: SSOP-16-150mil (KiCad packages3D, STEP)
  • 3D model files: uc3872mtr-etched.step / uc3872mtr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); uc3872mtr.step / uc3872mtr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (12 pp, sha256 4f021ba16ffe9cab, retrieved 2026-11-06, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text+vision), consensus claude-opus-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF