OPA890IDBVR from Texas Instruments, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin	Name	Type	Function
1	Output	output	Amplifier output, which goes high-impedance when DIS is pulled LOW; output swing is ±4.0V typical with no load on ±5V supplies.
2	-VS	power_in	Negative supply, with dual supplies of ±1.5V to ±6V (absolute maximum power supply ±6.5V) or ground for single-supply operation.
3	Noninverting Input	input	Noninverting input of the voltage-feedback op amp, with common-mode input range of ±3.9V typical on ±5V supplies.
4	Inverting Input	input	Inverting input of the voltage-feedback op amp, used with feedback resistor RF to set gain.
5	DIS	input	Disable control: left open or held HIGH the amplifier operates normally, pulled LOW supply current drops to less than 30μA and the output goes high-impedance.
6	+VS	power_in	Positive supply, +3V to +12V single supply or ±1.5V to ±6V dual supplies (absolute maximum power supply ±6.5V).

Key specifications

Parameter	Value
Manufacturer	Texas Instruments
Package	SOT-23-6
Category	Operational Amplifier/Comparator
Pins	6

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter	Symbol	Min	Typ	Max	Unit	Conditions	Page
Gain Bandwidth Product		130			MHz	G > +20V/V, VS=±5V	3
Small-Signal Bandwidth		115			MHz	G = +2V/V, VO = 100mVPP, VS=±5V	3
Small-Signal Bandwidth		13			MHz	G = +10V/V, VO = 100mVPP, VS=±5V	3
Slew Rate		500			V/μs	G = +2V/V, VO = 2V Step, VS=±5V	3
2nd-Harmonic Distortion				-88	dBc	G = +2V/V, f = 1MHz, VO = 2VPP, RL = 200Ω, VS=±5V	3
2nd-Harmonic Distortion				-102	dBc	G = +2V/V, f = 1MHz, VO = 2VPP, RL ≥ 500Ω, VS=±5V	3
3rd-Harmonic Distortion				-89	dBc	G = +2V/V, f = 1MHz, VO = 2VPP, RL = 200Ω, VS=±5V	3
3rd-Harmonic Distortion				-94	dBc	G = +2V/V, f = 1MHz, VO = 2VPP, RL ≥ 500Ω, VS=±5V	3
Input Voltage Noise				8	nV/√Hz	f > 100kHz, VS=±5V	3
Input Current Noise				1	pA/√Hz	f > 100kHz, VS=±5V	3
Open-Loop Voltage Gain (AOL)	AOL	62			dB	VO = 0V, RL = 100Ω, VS=±5V	3
Input Offset Voltage			1	5	mV	VCM = 0V, VS=±5V	3
Average Offset Voltage Drift				15	μV/°C	VCM = 0V, VS=±5V	3
Input Bias Current			0.1	1.6	μA	VCM = 0V, VS=±5V	3
Input Offset Current			70	350	nA	VCM = 0V, VS=±5V	3
Common-Mode Input Range (CMIR)		3.9			V	VS=±5V	3
Common-Mode Rejection Ratio (CMRR)		67			dB	VCM = 0V, Input-Referred, VS=±5V	3
Output Voltage Swing		4			V	No Load, VS=±5V	3
Output Voltage Swing		3.5			V	RL = 100Ω, VS=±5V	3
Output Current, Sourcing, Sinking		40			mA	VO = 0V, VS=±5V	3
Power-Down Supply Current (+VS)			30	55	μA	VDIS = 0, VS=±5V	4
Enable Voltage		3			V	VS=±5V	4
Disable Voltage				1.4	V	VS=±5V	4
Control Pin Input Bias Current (VDIS)	VDIS		15	30	μA	VDIS = 0V, Each Channel, VS=±5V	4
Maximum Operating Voltage				6	V	VS=±5V	4
Maximum Quiescent Current			1.1	1.2	mA	VS = ±5V	4
Minimum Quiescent Current		1.05	1.1		mA	VS = ±5V	4
Power-Supply Rejection Ratio (+PSRR)	+PSRR	74			dB	+VS = 4.5V to 5.5V, VS=±5V	4
Gain Bandwidth Product		125			MHz	G > +20V/V, VS=+5V	5
Small-Signal Bandwidth		105			MHz	G = +2V/V, VO = 100mVPP, VS=+5V	5
Small-Signal Bandwidth		12			MHz	G = +10V/V, VO = 100mVPP, VS=+5V	5
Slew Rate		350			V/μs	G = +2V/V, VO = 2V Step, VS=+5V	5
2nd-Harmonic Distortion				-85	dBc	G = +2V/V, f = 1MHz, VO = 2VPP, RL = 200Ω, VS=+5V	5
2nd-Harmonic Distortion				-90	dBc	G = +2V/V, f = 1MHz, VO = 2VPP, RL ≥ 500Ω, VS=+5V	5
3rd-Harmonic Distortion				-85	dBc	G = +2V/V, f = 1MHz, VO = 2VPP, RL = 200Ω, VS=+5V	5
3rd-Harmonic Distortion				-87	dBc	G = +2V/V, f = 1MHz, VO = 2VPP, RL ≥ 500Ω, VS=+5V	5
Input Voltage Noise				8.1	nV/√Hz	f > 100kHz, VS=+5V	5
Input Current Noise				1.1	pA/√Hz	f > 100kHz, VS=+5V	5
Open-Loop Voltage Gain (AOL)	AOL	60			dB	VO = VS/2, RL = 100Ω, VS=+5V	5
Input Offset Voltage			1	5	mV	VCM = VS/2, VS=+5V	5
Average Offset Voltage Drift				15	μV/°C	VCM = VS/2, VS=+5V	5
Input Bias Current			0.1	1.7	μA	VCM = VS/2, VS=+5V	5
Input Offset Current			70	400	nA	VCM = VS/2, VS=+5V	5
Most Positive Input Voltage		4			V	VS=+5V	5
Least Positive Input Voltage				1	V	VS=+5V	5
Common-Mode Rejection Ratio (CMRR)		65			dB	VCM = VS/2, Input-Referred, VS=+5V	5
Most Positive Output Voltage		4			V	No Load, VS=+5V	5
Most Positive Output Voltage		3.9			V	RL = 100Ω, VS=+5V	5
Least Positive Output Voltage				1	V	No Load, VS=+5V	5
Least Positive Output Voltage				1.1	V	RL = 100Ω, VS=+5V	5
Output Current: Sourcing, Sinking		35			mA	VO = VS/2, VS=+5V	5
Power-Down Supply Current (+VS)			18	45	μA	VDIS = 0V, both channels, VS=+5V	6
Maximum Operating Voltage				12	V	VS=+5V	6
Maximum Quiescent Current			1.06	1.18	mA	VS = +5V	6
Minimum Quiescent Current		0.92	1.06		mA	VS = +5V	6
Supply Voltage (Maximum)				6.5	V	Power Supply, ±VS	2
Storage Temperature Range		-65		125	°C		2
Maximum Junction Temperature	TJ			150	°C		2
ESD Rating: Human Body Model (HBM)				2000	V	Human Body Model (HBM)	2
Thermal Resistance, Junction-to-Ambient (DBV SOT23-6)	θJA		110		°C/W		4

CAD (KiCad official)

Symbol: OPA890IDBVR
Footprint: Package_TO_SOT_SMD:SOT-23-6
3D model: SOT-23-6 (KiCad packages3D, STEP)
3D model files: opa890idbvr-etched.step / opa890idbvr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); opa890idbvr.step / opa890idbvr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

Datasheet: Texas Instruments datasheet (37 pp, sha256 ef4f8e08ee4ab001, retrieved 2026-11-02, tier: manufacturer)
Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF

OPA890IDBVR

Changed since verified OPA890IDBVR

Verification log 1 record

3D Model

Symbol & Footprint

Schematic Symbol

PCB Footprint

Datasheet

README