3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownTLV9030L1QDCKRQ1
Texas Instruments · Integrated Circuits (ICs) · 6-TSSOP, SC-88, SOT-363
TLV9030L1QDCKRQ1 from Texas Instruments, in a 6-TSSOP, SC-88, SOT-363. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IN+ | input | Non-inverting (+) input; rail-to-rail and fault-tolerant, it tolerates up to 6V without damage and must stay within -0.2V to 5.5V from V- under recommended operating conditions. |
| 2 | V- | power_in | Negative supply voltage; the supply span (V+) - (V-) must be between 1.65V and 5.5V. |
| 3 | IN- | input | Inverting (-) input; must stay within -0.2V to 5.5V from V- under recommended operating conditions. |
| 4 | OUT | output | Push-pull output on the TLV903xL-Q1 that can sink and source up to 85mA, latching on the low-to-high output transition. |
| 5 | CLR | input | Clear input that resets the output latch on a falling edge; its range is -0.2V to 5.5V from V-. |
| 6 | V+ | power_in | Positive supply voltage; the supply span (V+) - (V-) must be between 1.65V and 5.5V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | 6-TSSOP, SC-88, SOT-363 |
| Category | Integrated Circuits (ICs) |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VS | 1.65 | 5.5 | V | VS = (V+) - (V-) | 5 | |
| Input voltage range (IN+, IN-, CLR) from (V-) | -0.2 | 5.5 | V | 5 | |||
| Output voltage range, open drain output, from (V-) | 0 | 5.5 | V | open drain output | 5 | ||
| Ambient temperature | TA | -40 | 125 | °C | 5 | ||
| Supply voltage | VS | -0.3 | 6 | V | VS = (V+), (V-) | 5 | |
| Input pins (IN+, IN-, CLR) from (V-) | -0.3 | 6 | V | 5 | |||
| Current into input pins (IN+, IN-, CLR) | -10 | 10 | mA | 5 | |||
| Output (OUT) from (V-) | -0.3 | 6 | V | 5 | |||
| Output short circuit duration | 10 | s | short to (V-) or (V+) | 5 | |||
| Junction temperature | TJ | 150 | °C | 5 | |||
| Storage temperature | Tstg | -65 | 150 | °C | 5 | ||
| Electrostatic discharge, human-body model (HBM) | V(ESD) | -2000 | 2000 | V | per AEC Q100-002 | 5 | |
| Electrostatic discharge, charged-device model (CDM) | V(ESD) | -1000 | 1000 | V | per AEC Q100-011 | 5 | |
| Input threshold voltage | VT | -1.75 | 0.3 | 1.75 | mV | VS = 1.8V and 5V | 7 |
| Input threshold voltage | VT | -2.25 | 2.25 | mV | VS = 1.8V and 5V, TA = -40°C to +125°C | 7 | |
| Input threshold voltage drift | dVT/dT | -0.5 | 0.5 | µV/°C | VS = 1.8V and 5V, TA = -40°C to +125°C | 7 | |
| Quiescent current per comparator | IQ | 22 | 30 | µA | VS = 1.8V and 5V, No Load, Output Low | 7 | |
| Quiescent current per comparator | IQ | 42 | µA | VS = 1.8V and 5V, No Load, Output Low, TA = -40°C to +125°C | 7 | ||
| Power-supply rejection ratio (push-pull) | PSRR | 75 | 95 | dB | VS = 1.8V to 5V, TA = -40°C to +125°C (push-pull only) | 7 | |
| Power-supply rejection ratio (open drain) | PSRR | 80 | 95 | dB | VS = 1.8V to 5V, TA = -40°C to +125°C (open drain only) | 7 | |
| Voltage input high threshold of CLR | VIH_CLR | 1.2 | V | 7 | |||
| Voltage input low threshold of CLR | VIL_CLR | 0.6 | V | 7 | |||
| Common-mode rejection ratio (5V) | CMRR | 60 | 70 | dB | VS = 5V, (V-), 0.2V < VCM < (V+) + 0.2V, TA = -40°C to +125°C | 7 | |
| Common-mode rejection ratio (1.8V) | CMRR | 50 | 60 | dB | VS = 1.8V, (V-), 0.2V < VCM < (V+) + 0.2V, TA = -40°C to +125°C | 7 | |
| Voltage swing from (V-) | VOL | 75 | 125 | mV | ISINK = 4mA, TA = 25°C | 7 | |
| Voltage swing from (V-) | VOL | 175 | mV | ISINK = 4mA, TA = -40°C to +125°C | 7 | ||
| Voltage swing from (V+) | VOH | 75 | 125 | mV | ISOURCE = 4mA, TA = 25°C (push-pull only) | 7 | |
| Voltage swing from (V+) | VOH | 175 | mV | ISOURCE = 4mA, TA = -40°C to +125°C (push-pull only) | 7 | ||
| Open-drain output leakage current | ILKG | 100 | pA | VPULLUP = (V+), TA = 25°C | 7 | ||
| Short-circuit current (sinking) | ISC | 75 | 85 | mA | VS = 5V, Sinking | 7 | |
| Short-circuit current (sourcing) | ISC | 75 | 85 | mA | VS = 5V, Sourcing (push-pull only) | 7 | |
| Propagation delay time, high-to-low (open-drain only) | TPD-HL | 110 | ns | VID = -100mV, CLR = 0V, RP = 2.5KΩ | 8 | ||
| Propagation delay time, low-to-high (push-pull only) | TPD-LH | 125 | ns | VID = +100mV, CLR = 0V | 8 | ||
| Clear fall to latch reset propagation delay time | TPD-CLR-F | 25 | 70 | ns | CLR = 1.8V to 5V | 8 | |
| Minimum clear hold pulse time | CLR_Min | 10 | ns | CLR = 1.8V to 5V | 8 | ||
| 5V output fall time, 80% to 20% | TFALL | 3 | ns | VID = -100mV | 8 | ||
| 5V output rise time, 20% to 80% (push-pull only) | TRISE | 3 | ns | VID = +100mV, push-pull only | 8 | ||
| Power on time | PON | 35 | µs | 8 | |||
| Input bias current | IB | 5 | pA | VCM = VS/2 | 7 | ||
| Input offset current | IOS | 1 | pA | VCM = VS/2 | 7 | ||
| Input capacitance, differential | CID | 2 | pF | VCM = VS/2 | 7 | ||
| Input capacitance, common mode | CIC | 3 | pF | VCM = VS/2 | 7 | ||
| Power-on reset voltage (positive) | VPOR | 1.25 | V | 7 | |||
| Junction-to-ambient thermal resistance (DCK, SC-70) | θJA | 210.5 | °C/W | 6 | |||
| Junction-to-case (top) thermal resistance (DCK, SC-70) | θJC(top) | 143.9 | °C/W | 6 | |||
| Junction-to-board thermal resistance (DCK, SC-70) | θJB | 64.7 | °C/W | 6 | |||
| Junction-to-top characterization parameter (DCK, SC-70) | ψJT | 46.1 | °C/W | 6 | |||
| Junction-to-board characterization parameter (DCK, SC-70) | ψJB | 64.5 | °C/W | 6 |
CAD (Adom-generated)
- Symbol:
TLV9030L1QDCKRQ1 - Footprint:
Adom_Gen:Texas_Instruments_TLV9030_a02d67 - 3D model: generated to fit the land (STEP)
- 3D model files:
tlv9030l1qdckrq1-etched.step/tlv9030l1qdckrq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tlv9030l1qdckrq1.step/tlv9030l1qdckrq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (36 pp, sha256
04bf1a8ebbea4277, retrieved 2026-11-17, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land.