3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLMR14050SQDPRTQ1
Texas Instruments · DC-DC Converters · WSON-10-EP(4x4)
LMR14050SQDPRTQ1 from Texas Instruments, in a WSON-10-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BOOT | passive | Bootstrap capacitor connection for the high-side MOSFET driver; connect a high quality 0.1 µF capacitor from BOOT to SW (BOOT to SW max 6.5 V in DPR package). |
| 2 | VIN | power_in | Connects to the power supply and bypass capacitors CIN (4 V to 40 V operating); the path from VIN to the high frequency bypass CIN and GND must be as short as possible. |
| 3 | VIN | power_in | Second VIN pin, connected to the power supply and bypass capacitors CIN (4 V to 40 V operating) with the same short path to CIN and GND. |
| 4 | EN | input | Enable pin with internal pull-up current source; pull below 1.2 V to disable, float or connect to VIN to enable, and adjust the input undervoltage lockout with two resistors. |
| 5 | RT/SYNC | input | Resistor timing or external clock input; a resistor to ground sets switching frequency (200 kHz to 2500 kHz), or the pin becomes a high-impedance synchronization input to the internal PLL when pulled above the PLL upper threshold. |
| 6 | SS | input | Soft-start control pin; connect a capacitor to set the soft-start time. |
| 7 | FB | input | Feedback input connected to the feedback divider to set VOUT; do not short this pin to ground during operation. |
| 8 | PGOOD | output | Open drain power-good flag output; use a 10 kΩ to 100 kΩ pull-up resistor to a logic rail or DC voltage no higher than 7 V. |
| 9 | GND | power_in | System ground pin. |
| 10 | SW | passive | Switching output of the regulator, internally connected to the high-side power MOSFET; connect to the power inductor. |
| 11 | Thermal Pad | power_in | Exposed pad and major heat dissipation path of the die; must be connected to the ground plane on the PCB. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WSON-10-EP(4x4) |
| Category | Power Supply Chip |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operation input voltage | VIN | 4 | 40 | V | 5 | ||
| UVLO rising threshold | UVLO | 3.5 | 3.7 | 3.9 | V | Rising threshold | 5 |
| Shutdown supply current | ISHDN | 1 | 3 | μA | VEN = 0 V, TJ = 25°C, 4.0 V ≤ VIN ≤ 40 V | 5 | |
| EN threshold voltage | VEN_TH | 1.05 | 1.2 | 1.38 | V | 5 | |
| PGOOD leakage current at high level output | IPG | 10 | 200 | nA | VPull-Up = 5 V | 5 | |
| Minimum VIN for valid PGOOD output | VIN_PG_MIN | 1.6 | 1.95 | V | VPull-Up < 5 V at IPull-Up = 100 μA | 5 | |
| Feedback voltage | VFB | 0.744 | 0.75 | 0.756 | V | TJ = 25°C | 5 |
| Feedback voltage over temperature | VFB | 0.735 | 0.75 | 0.765 | V | TJ = -40 °C to 125°C | 5 |
| High-side MOSFET on-resistance | RDS_ON | 90 | 180 | mΩ | VIN = 12 V | 6 | |
| Current limit | ILIMT | 5.8 | 7.9 | 10.9 | A | VIN = 12 V, TJ = -40°C to 125°C, Open Loop | 6 |
| Switching frequency | fSW | 1758 | 1912 | 2066 | kHz | RT = 11.5 kΩ | 6 |
| Switching frequency range at SYNC mode | fSW | 250 | 2300 | kHz | 6 | ||
| Absolute max VIN, EN to GND | VIN, EN | -0.3 | 44 | V | 4 | ||
| Absolute max BOOT to GND | BOOT | -0.3 | 49 | V | 4 | ||
| Absolute max SS to GND | SS | -0.3 | 5 | V | 4 | ||
| Absolute max FB to GND (DPR package) | FB | -0.3 | 7 | V | DPR package | 4 | |
| Absolute max RT/SYNC to GND | RT/SYNC | -0.3 | 3.6 | V | 4 | ||
| Absolute max PGOOD to GND | PGOOD | -0.3 | 7 | V | 4 | ||
| Absolute max BOOT to SW (DPR package) | BOOT to SW | 6.5 | V | DPR package | 4 | ||
| Absolute max SW to GND | SW | -3 | 44 | V | 4 | ||
| Junction temperature (absolute max) | TJ | -40 | 150 | °C | 4 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| ESD HBM | V(ESD) | -2000 | 2000 | V | Human-body model, per AEC Q100-002 | 4 | |
| ESD CDM | V(ESD) | -750 | 750 | V | Charged-device model, per AEC Q100-011 | 4 | |
| Recommended VIN | VIN | 4 | 40 | V | 4 | ||
| Recommended VOUT | VOUT | 0.8 | 28 | V | 4 | ||
| Recommended BOOT | BOOT | 45 | V | 4 | |||
| Recommended SW | SW | -1 | 40 | V | 4 | ||
| Recommended FB | FB | 0 | 5 | V | 4 | ||
| Recommended EN | EN | 0 | 40 | V | 4 | ||
| Recommended RT/SYNC | RT/SYNC | 0 | 3.3 | V | 4 | ||
| Recommended SS | SS | 0 | 3 | V | 4 | ||
| Recommended PGOOD to GND | PGOOD | 0 | 5 | V | 4 | ||
| Switching frequency range at RT mode | fSW | 200 | 2500 | kHz | 4 | ||
| Switching frequency range at SYNC mode (recommended) | fSW | 250 | 2300 | kHz | 4 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 4 | ||
| Operating quiescent current (non-switching) | IQ | 40 | μA | VFB = 1.0 V, TJ = 25°C | 5 | ||
| UVLO hysteresis | UVLO | 285 | mV | Hysteresis | 5 | ||
| EN hysteresis current | IEN_HYS | -3.6 | μA | 5 | |||
| SS pin current | ISS | -3 | μA | TJ = 25°C | 5 | ||
| Thermal shutdown threshold | TSHDN | 170 | °C | 6 | |||
| Thermal shutdown hysteresis | THYS | 12 | °C | 6 | |||
| Minimum controllable on time | TON_MIN | 75 | ns | VIN = 12 V, ILoad = 1 A | 6 | ||
| Maximum duty cycle | DMAX | 97 | % | fSW = 200 kHz | 6 | ||
| Junction-to-ambient thermal resistance (DPR) | RθJA | 36.5 | °C/W | DPR (WSON) 10 pins | 5 | ||
| Junction-to-case (bottom) thermal resistance (DPR) | RθJC(bot) | 3.1 | °C/W | DPR (WSON) 10 pins | 5 | ||
| Junction-to-case (top) thermal resistance (DPR) | RθJC(top) | 35.2 | °C/W | DPR (WSON) 10 pins | 5 | ||
| Junction-to-board thermal resistance (DPR) | RθJB | 13.6 | °C/W | DPR (WSON) 10 pins | 5 | ||
| Junction-to-top characterization parameter (DPR) | ψJT | 0.3 | °C/W | DPR (WSON) 10 pins | 5 | ||
| Junction-to-board characterization parameter (DPR) | ψJB | 13.8 | °C/W | DPR (WSON) 10 pins | 5 |
CAD (KiCad official)
- Symbol:
LMR14050SQDPRTQ1 - Footprint:
Package_SON:WSON-10-1EP_4x4mm_P0.8mm_EP2.6x3mm - 3D model: WSON-10-EP(4x4) (KiCad packages3D, STEP)
- 3D model files:
lmr14050sqdprtq1-etched.step/lmr14050sqdprtq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lmr14050sqdprtq1.step/lmr14050sqdprtq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (38 pp, sha256
cefdbbf1b3380e4f, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).