3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownPIC16C711-20I
Microchip Tech · MICROCHIP · PDIP-18
PIC16C711-20I from Microchip Tech, in a PDIP-18. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RA2/AN2 | bidirectional | PORTA bit RA2 is a bidirectional TTL I/O that can also be analog input 2 (AN2). |
| 2 | RA3/AN3/VREF | bidirectional | PORTA bit RA3 is a bidirectional TTL I/O that can also be analog input 3 or the analog reference voltage (VREF). |
| 3 | RA4/T0CKI | bidirectional | PORTA bit RA4 is a bidirectional Schmitt Trigger I/O that can also be the clock input to the Timer0 module, and its output is open drain type. |
| 4 | MCLR/VPP | input | Master clear (reset) input or programming voltage input; this pin is an active low reset to the device. |
| 5 | VSS | power_in | Ground reference for logic and I/O pins. |
| 6 | RB0/INT | bidirectional | PORTB bit RB0 is a bidirectional I/O with TTL/Schmitt Trigger input that can also be the external interrupt pin (Schmitt Trigger when configured as external interrupt). |
| 7 | RB1 | bidirectional | PORTB bit RB1 is a bidirectional TTL I/O with internal weak pull-up selectable by software. |
| 8 | RB2 | bidirectional | PORTB bit RB2 is a bidirectional TTL I/O with internal weak pull-up selectable by software. |
| 9 | RB3 | bidirectional | PORTB bit RB3 is a bidirectional TTL I/O with internal weak pull-up selectable by software. |
| 10 | RB4 | bidirectional | PORTB bit RB4 is a bidirectional TTL I/O with interrupt-on-change capability. |
| 11 | RB5 | bidirectional | PORTB bit RB5 is a bidirectional TTL I/O with interrupt-on-change capability. |
| 12 | RB6 | bidirectional | PORTB bit RB6 is a bidirectional I/O with interrupt-on-change capability that serves as the serial programming clock (Schmitt Trigger input in serial programming mode). |
| 13 | RB7 | bidirectional | PORTB bit RB7 is a bidirectional I/O with interrupt-on-change capability that serves as the serial programming data (Schmitt Trigger input in serial programming mode). |
| 14 | VDD | power_in | Positive supply for logic and I/O pins. |
| 15 | OSC2/CLKOUT | output | Oscillator crystal output connecting to crystal or resonator in crystal oscillator mode; in RC mode it outputs CLKOUT at 1/4 the OSC1 frequency. |
| 16 | OSC1/CLKIN | input | Oscillator crystal input or external clock source input (Schmitt Trigger when in RC mode, CMOS input otherwise). |
| 17 | RA0/AN0 | bidirectional | PORTA bit RA0 is a bidirectional TTL I/O that can also be analog input 0 (AN0). |
| 18 | RA1/AN1 | bidirectional | PORTA bit RA1 is a bidirectional TTL I/O that can also be analog input 1 (AN1). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | PDIP-18 |
| Category | Embedded Processors & Controllers |
| Pins | 18 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage (XT, RC and LP oscillator) | VDD | 4 | 6 | V | XT, RC and LP osc configuration | 90 | |
| Supply Voltage (HS oscillator) | VDD | 4.5 | 5.5 | V | HS osc configuration | 90 | |
| VDD rise rate to ensure internal Power-on Reset signal | SVDD | 0.05 | V/ms | See section on Power-on Reset for details | 90 | ||
| Brown-out Reset Voltage | BVDD | 3.7 | 4 | 4.3 | V | BODEN configuration bit is enabled | 90 |
| Supply Current (XT, RC) | IDD | 2.7 | 5 | mA | XT, RC osc configuration; FOSC = 4 MHz, VDD = 5.5V (Note 4) | 90 | |
| Supply Current (HS) | IDD | 13.5 | 30 | mA | HS osc configuration FOSC = 20 MHz, VDD = 5.5V | 90 | |
| Brown-out Reset Current (delta) | ΔIBOR | 300 | 500 | µA | BOR enabled VDD = 5.0V | 90 | |
| Power-down Current (WDT enabled) | IPD | 10.5 | 42 | µA | VDD = 4.0V, WDT enabled, -40°C to +85°C | 90 | |
| Power-down Current (WDT disabled, 0 to 70 C) | IPD | 1.5 | 21 | µA | VDD = 4.0V, WDT disabled, -0˚C to +70˚C | 90 | |
| Power-down Current (WDT disabled, -40 to +85 C) | IPD | 1.5 | 24 | µA | VDD = 4.0V, WDT disabled, -40°C to +85°C | 90 | |
| Power-down Current (WDT disabled, -40 to +125 C) | IPD | 1.5 | 30 | µA | VDD = 4.0V, WDT disabled, -40°C to +125°C | 90 | |
| Input High Voltage, I/O ports with TTL buffer | VIH | 2 | V | 4.5 ≤ VDD ≤ 5.5V | 92 | ||
| Input Leakage Current, I/O ports | IIL | -1 | 1 | µA | Vss ≤ VPIN ≤ VDD, Pin at hi-impedance | 92 | |
| Input Leakage Current, MCLR, RA4/T0CKI | IIL | -5 | 5 | µA | Vss ≤ VPIN ≤ VDD | 92 | |
| Input Leakage Current, OSC1 | IIL | -5 | 5 | µA | Vss ≤ VPIN ≤ VDD, XT, HS and LP osc configuration | 92 | |
| PORTB weak pull-up current | IPURB | 50 | 250 | 400 | µA | VDD = 5V, VPIN = VSS | 92 |
| Output Low Voltage, I/O ports | VOL | 0.6 | V | IOL = 8.5 mA, VDD = 4.5V, -40°C to +85°C | 93 | ||
| Output Low Voltage, I/O ports (extended) | VOL | 0.6 | V | IOL = 7.0 mA, VDD = 4.5V, -40°C to +125°C | 93 | ||
| Output Low Voltage, OSC2/CLKOUT (RC osc) | VOL | 0.6 | V | IOL = 1.6 mA, VDD = 4.5V, -40°C to +85°C | 93 | ||
| Output Low Voltage, OSC2/CLKOUT (RC osc, extended) | VOL | 0.6 | V | IOL = 1.2 mA, VDD = 4.5V, -40°C to +125°C | 93 | ||
| A/D absolute error (integral linearity error EIL row shown below; EABS row as printed) | EABS | -1 | 1 | LSb | VREF = VDD, VSS ≤ AIN ≤ VREF | 99 | |
| Integral linearity error | EIL | -1 | 1 | LSb | VREF = VDD, VSS ≤ AIN ≤ VREF | 99 | |
| Full scale error | EFS | -1 | 1 | LSb | VREF = VDD, VSS ≤ AIN ≤ VREF | 99 | |
| Reference voltage | VREF | 2.5 | V | 99 | |||
| Recommended impedance of analog voltage source | ZAIN | 10 | kΩ | 99 | |||
| VREF input current, during VAIN acquisition | IREF | 10 | µA | During VAIN acquisition. Based on differential of VHOLD to VAIN. To charge CHOLD see Section 7.1. | 99 | ||
| VREF input current, during A/D conversion cycle | IREF | 1000 | µA | During A/D Conversion cycle | 99 | ||
| A/D clock period (TOSC based) | TAD | 1.6 | µs | TOSC based, VREF ≥ 3.0V | 100 | ||
| A/D clock period (A/D RC mode) | TAD | 2 | 4 | 6 | µs | A/D RC mode | 100 |
| Acquisition time (minimum, amplifier settling) | TACQ | 5 | µs | The minimum time is the amplifier settling time. This may be used if the new input voltage has not changed by more than 1 LSb (i.e., 19.5 mV @ 5.12V) from the last sampled voltage (as stated on CHOLD). | 100 | ||
| Acquisition time | TACQ | 20 | µs | See Section 7.1 for min conditions (Note 2) | 100 | ||
| Switching from convert to sample time | TSWC | 1.5 | TAD | 100 | |||
| External CLKIN Frequency (HS -20) | Fosc | 20 | MHz | DC, 20 MHz HS osc mode (-20) | 95 | ||
| External CLKIN Period (HS -20) | Tosc | 50 | ns | HS osc mode (-20) | 95 | ||
| Instruction Cycle Time | TCY | 200 | ns | TCY = 4/FOSC | 95 | ||
| External Clock in (OSC1) High or Low Time (HS) | TosL, TosH | 10 | ns | HS oscillator | 95 | ||
| External Clock in (OSC1) Rise or Fall Time (HS) | TosR, TosF | 15 | ns | HS oscillator | 95 | ||
| OSC1↑ to CLKOUT↓ | TosH2ckL | 15 | 30 | ns | Note 1: measurements in RC mode, CLKOUT = 4 x TOSC | 96 | |
| OSC1↑ to CLKOUT↑ | TosH2ckH | 15 | 30 | ns | Note 1: measurements in RC mode, CLKOUT = 4 x TOSC | 96 | |
| CLKOUT rise time | TckR | 5 | 15 | ns | Note 1: measurements in RC mode, CLKOUT = 4 x TOSC | 96 | |
| CLKOUT fall time | TckF | 5 | 15 | ns | Note 1: measurements in RC mode, CLKOUT = 4 x TOSC | 96 | |
| Port output rise time (PIC16C710/711) | TioR | 10 | 25 | ns | PIC16C710/711 | 96 | |
| Port output fall time (PIC16C710/711) | TioF | 10 | 25 | ns | PIC16C710/711 | 96 | |
| INT pin high or low time | Tinp | 20 | ns | Asynchronous event, not related to any internal clock edges | 96 | ||
| RB7:RB4 change INT high or low time | Trbp | 20 | ns | Asynchronous event, not related to any internal clock edges | 96 | ||
| Ambient temperature under bias | -55 | 125 | °C | 89 | |||
| Storage temperature | -65 | 150 | °C | 89 | |||
| Voltage on VDD with respect to VSS | VDD | -0.3 | 7.5 | V | 89 | ||
| Voltage on any pin with respect to VSS (except VDD, MCLR, and RA4); max printed as (VDD + 0.3V) | -0.3 | V | 89 | ||||
| Voltage on MCLR with respect to VSS | 0 | 14 | V | 89 | |||
| Voltage on RA4 with respect to Vss | 0 | 14 | V | 89 | |||
| Total power dissipation | 1 | W | Note 1 (power dissipation calculated per printed formula) | 89 | |||
| Maximum current out of VSS pin | 300 | mA | 89 | ||||
| Input clamp current, IIK | IIK | -20 | 20 | mA | VI < 0 or VI > VDD | 89 | |
| Output clamp current, IOK | IOK | -20 | 20 | mA | VO < 0 or VO > VDD | 89 | |
| Maximum output current sunk by any I/O pin | 25 | mA | 89 | ||||
| Maximum output current sourced by any I/O pin | 25 | mA | 89 | ||||
| Operating temperature (industrial) | TA | -40 | 85 | °C | -40˚C ≤ TA ≤ +85˚C (industrial) | 90 |
CAD (KiCad official)
- Symbol:
PIC16C711-20I - Footprint:
Package_DIP:DIP-18_W7.62mm - 3D model: PDIP-18 (KiCad packages3D, STEP)
- 3D model files:
pic16c711-20i-etched.step/pic16c711-20i-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pic16c711-20i.step/pic16c711-20i.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (177 pp, sha256
83dc8dffb92c2c94, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).