component
AP5054BES5C
Public Made by Adomby adom
Wuxi Chipown Micro-electronics Battery Management, SOT-23-5. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownAP5054BES5C
Wuxi Chipown Micro-electronics · Battery Management · SOT-23-5
AP5054BES5C from Wuxi Chipown Micro-electronics, in a SOT-23-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CHRG | output | Open-drain charge status output that is pulled low through an internal N-channel MOSFET while charging and goes high-impedance when the charge cycle completes or the part is in undervoltage lockout; V_CHRG is 1.5 V max at I_CHRG = 1 mA. |
| 2 | GND | power_in | Power ground reference for the charger. |
| 3 | BAT | power_out | Battery connection that supplies charge current and regulates the final float voltage to 4.2 V (V_float 4.16 V to 4.24 V at 0 °C to 85 °C). |
| 4 | VCC | power_in | Charger input supply, 4.25 V to 5.5 V, which requires a capacitor of at least 1 µF; the input OVP threshold is 5.75 V to 6.3 V. |
| 5 | PROG | passive | For AP5054BES5C, a 1% precision resistor from this pin to GND sets the charge current via I_BAT = (V_PROG / R_PROG) × 1000, with V_PROG held at 1 V in constant-current mode; a shutdown threshold of 1.21 V applies when the resistor is disconnected. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Wuxi Chipown Micro-electronics |
| Package | SOT-23-5 |
| Category | Power Management (PMIC) |
| Pins | 5 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 输入电源电压 (input supply voltage) | Vcc | 4.25 | 5.5 | V | 3 | ||
| 输入 OVP (input overvoltage threshold) | Vcc-OVP | 5.75 | 6.3 | V | 3 | ||
| 停机模式 supply current (shutdown) | Icc | 150 | 500 | μA | 待机模式 (standby mode), as printed in the row | 3 | |
| 停机模式 supply current (shutdown) | Icc | 50 | 100 | μA | 停机模式(RPROG 未连接,Vcc<Vbat or Vcc<Vuv) | 3 | |
| 稳定输出（浮充）电压 (float voltage) | Vfloat | 4.16 | 4.2 | 4.24 | V | 0°C≤ TA≤ 85°C, IBAT = 40mA | 3 |
| BAT pin charge current, current mode | Ibat | 85 | 100 | 110 | mA | RPROG =10k, 电流模式 | 3 |
| BAT pin charge current, current mode | Ibat | 465 | 500 | 530 | mA | RPROG =2k, 电流模式 | 3 |
| BAT pin current, standby | Ibat | 0 | -2.5 | -6 | μA | 待机模式,Vbat=4.2V | 3 |
| BAT pin current, shutdown mode | Ibat | -1 | -2.5 | μA | 关断模式 | 3 | |
| BAT pin current, sleep mode | Ibat | -0.05 | -0.5 | μA | 睡眠模式,Vcc=0V | 3 | |
| 涓流充电电流 (trickle charge current) | Itrikl | 125 | 150 | 175 | mA | Vbat<Vtrikl,Rprog=2k | 3 |
| 涓流充电阈值电压 (trickle charge threshold) | Vtrikl | 2.78 | 2.9 | 3.05 | V | Vbat 上升 | 3 |
| 涓流电压迟滞电压 (trickle threshold hysteresis) | Vtrhys | 120 | 160 | 250 | mV | 3 | |
| VCC欠压锁定阈值 (VCC undervoltage lockout) | Vuv | 3.6 | 3.8 | 4.1 | V | Vcc 从低到高 | 3 |
| VCC欠压闭锁滞后 (UVLO hysteresis) | Vuvhys | 150 | 200 | 300 | mV | 3 | |
| 手动关断阈值电压 (manual shutdown threshold) | Vmsd | 1.15 | 1.25 | 1.3 | V | PROG 上升 | 3 |
| 手动关断阈值电压 (manual shutdown threshold) | Vmsd | 0.9 | 1 | 1.2 | V | PROG 下降 | 3 |
| VCC-VBAT锁定阈值电压 (VCC-VBAT lockout threshold) | Vasd | 45 | 280 | 400 | mV | Vcc 从低到高 | 3 |
| VCC-VBAT锁定阈值电压 (VCC-VBAT lockout threshold) | Vasd | 5 | 100 | 230 | mV | Vcc 从高到低 | 3 |
| PROG端电压 (PROG pin voltage) | Vprog | 0.93 | 1 | 1.07 | V | 电流模式 | 3 |
| CHRG引脚输出低电压 (CHRG output low voltage) | Vchrg | 1.2 | 1.5 | V | Ichrg=1mA | 3 | |
| 电池再充电阈值电压 (recharge threshold) | ΔVrecg | 80 | 150 | 280 | mV | VFLOAT - VRECHRG | 3 |
| Vcc 绝对最大额定值 (input supply voltage, absolute maximum) | Vcc | -0.3 | 7 | V | Printed as VSS-0.3～VSS+7 | 2 | |
| PROG 端电压 (PROG pin voltage, absolute maximum) | Vprog | -0.3 | 3 | V | Printed as VSS-0.3～3 | 2 | |
| BAT 端电压 (BAT pin voltage, absolute maximum) | Vbat | -0.3 | 7 | V | Printed as Vss-0.3～7 | 2 | |
| CHRG 端电压 (CHRG pin voltage, absolute maximum) | Vchrg | -0.3 | 7 | V | Printed as VSS-0.3～VSS+7 | 2 | |
| BAT 端电流 (BAT pin current, absolute maximum) | Ibat | 750 | mA | 2 | |||
| PROG 端电流 (PROG pin current, absolute maximum) | Iprog | 750 | μA | 2 | |||
| 工作环境温度 (operating ambient temperature) | Topa | -40 | 85 | °C | 2 | ||
| 储存温度 (storage temperature) | Tstr | -65 | 125 | °C | 2 | ||
| 引脚温度 (lead temperature, soldering) | 260 | °C | 焊接,10s (soldering, 10 s) | 2 |
CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol:
AP5054BES5C - Footprint:
Package_TO_SOT_SMD:SOT-23-5 - 3D model: SOT-23-5, generated on the KiCad land (body 1.6 x 2.95 mm, terminals on the pads, 1.15 mm tall, datasheet A, midpoint of min and max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
ap5054bes5c-etched.step/ap5054bes5c-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ap5054bes5c.step/ap5054bes5c.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Wuxi Chipown Micro-electronics datasheet (9 pp, sha256
0e92367c5b1bb7ba, retrieved 2026-11-12, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).