Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

STUSB1600AQTR

STMicroelectronics · Power Distribution Switches · QFN-24-EP(4x4)

STUSB1600AQTR from STMicroelectronics, in a QFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 CC1DB input Dead-battery enable pull-down on CC1 pin, connect to CC1 or ground for dead-battery mode support (0 to 5.5 V operating)
2 CC1 bidirectional Type-C configuration channel 1 for attach detection, plug orientation, and system configuration with high voltage protection up to 22 V (0 to 5.5 V operating)
3 VCONN power_in Power input for active cable with integrated current-limited high-side power switches; 350 mA default, programmable 100-600 mA by 50 mA steps (2.7 to 5.5 V)
4 CC2 bidirectional Type-C configuration channel 2 for attach detection, plug orientation, and system configuration with high voltage protection up to 22 V (0 to 5.5 V operating)
5 CC2DB input Dead-battery enable pull-down on CC2 pin, connect to CC2 or ground for dead-battery mode support (0 to 5.5 V operating)
6 RESET input Active high reset input to initialize device logic and Type-C FSM (0 to 4.5 V operating)
7 SCL input I²C clock input requiring external pull-up resistor; up to 400 kHz fast mode (0 to 4.5 V operating)
8 SDA tri_state I²C open-drain data input/output, active low with external pull-up resistor required; up to 400 kHz fast mode (0 to 4.5 V operating)
9 ALERT# tri_state I²C interrupt, open-drain output active low indicating status changes in monitored registers with external pull-up required (0 to 4.5 V operating)
10 GND power_in Ground reference (0 V)
11 VBUS_VALID tri_state VBUS detection open-drain output, active low when VBUS voltage is within valid operating range; external pull-up required (0 to 4.5 V operating)
12 ATTACH tri_state Attachment detection open-drain output, active low when valid source-to-sink connection is established or accessory detected; external pull-up required (0 to 4.5 V operating)
13 ADDR0 input I²C device address selection input bit; low selects address 0x28, high selects address 0x29 for two-device configurations (0 to 4.5 V operating)
14 DEBUG1 tri_state Debug accessory detection in sink power role, open-drain output active low asserted when in DebugAccessory.SNK state; external pull-up required (0 to 4.5 V operating)
15 DEBUG2 tri_state Debug accessory detection in source power role, open-drain output active low asserted in UnorientedDebugAccessory.SRC or OrientedDebugAccessory.SRC states; external pull-up required (0 to 4.5 V operating)
16 NC unconnected No connection; reserved floating pin
17 A_B_SIDE tri_state Cable orientation open-drain output for USB SuperSpeed mux control: HiZ indicates CC1 attached, 0 indicates CC2 attached; external pull-up required (0 to 4.5 V operating)
18 VBUS_SENSE input High voltage analog input for VBUS voltage monitoring, discharge path control, and attachment detection in valid voltage range (0 to 22 V operating, 28 V absolute maximum)
19 VBUS_EN_SNK tri_state VBUS sink power path enable, open-drain output active low to drive external PMOS when connection established and VBUS valid (0 to 22 V operating, 28 V absolute maximum)
20 VBUS_EN_SRC tri_state VBUS source power path enable, open-drain output active low to drive external PMOS when connection established and VBUS valid (0 to 22 V operating, 28 V absolute maximum)
21 VREG_1V2 power_out 1.2 V internal regulator output; requires 1 µF typical decoupling capacitor (0.5 µF minimum, 10 µF maximum)
22 VSYS power_in Low power system supply input from battery or system power supply (3.0 to 5.5 V); connect to ground if not used
23 VREG_2V7 power_out 2.7 V internal regulator output; requires 1 µF typical decoupling capacitor (0.5 µF minimum, 10 µF maximum)
24 VDD power_in Main power supply from USB VBUS for high voltage domain; supports 4.1 to 22 V operating range with 28 V absolute maximum
25 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package QFN-24-EP(4x4)
Category Power Management (PMIC)
Pins 25

CAD (KiCad official)

  • Symbol: STUSB1600AQTR
  • Footprint: Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.7x2.7mm
  • 3D model: QFN-24-EP(4x4) (KiCad packages3D, STEP)
  • 3D model files: stusb1600aqtr-etched.step / stusb1600aqtr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); stusb1600aqtr.step / stusb1600aqtr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (66 pp, sha256 9211c19349c2e890, retrieved 2026-09-27, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-4-6 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF