component
24LC024T-E
Public Made by Adomby adom
Microchip Tech Pre-ordered Chips, SOIC-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdown24LC024T-E
Microchip Tech · Pre-ordered Chips · SOIC-8
24LC024T-E from Microchip Tech, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | A0 | input | Chip-select address input whose level is compared with the slave address bit; it must be tied to VCC or VSS, and up to eight devices can share the bus using different combinations. |
| 2 | A1 | input | Chip-select address input whose level is compared with the slave address bit; it must be tied to VCC or VSS, and up to eight devices can share the bus using different combinations. |
| 3 | A2 | input | Chip-select address input whose level is compared with the slave address bit; it must be tied to VCC or VSS, and up to eight devices can share the bus using different combinations. |
| 4 | VSS | power_in | Ground reference for the device. |
| 5 | SDA | bidirectional | Open-drain serial address/data I/O that requires a pull-up resistor to VCC (typically 10 kΩ for 100 kHz or 2 kΩ for 400 kHz), and may change only while SCL is low except for Start and Stop conditions. |
| 6 | SCL | input | Serial clock input that synchronizes all data transfer to and from the device. |
| 7 | WP | input | Hardware write-protect input that must be tied to VCC (write protection enabled) or VSS (write protection disabled); available only on the 24XX024. |
| 8 | VCC | power_in | Power supply; the device selection table specifies 2.5V to 5.5V for the 24LC024, while the pin table lists +1.7 to 5.5V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOIC-8 |
| Category | Interface ICs |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| All inputs and outputs w.r.t. VSS | -0.3 | V | Upper limit printed as VCC + 1.0V | 2 | |||
| Storage temperature | -65 | 150 | °C | 2 | |||
| Ambient temperature with power applied | -40 | 125 | °C | 2 | |||
| ESD protection on all pins | 4 | kV | ≥ 4 kV as printed | 2 | |||
| Supply voltage (Automotive E grade) | VCC | 2.5 | 5.5 | V | Automotive (E): TA = -40°C to +125°C | 2 | |
| Ambient temperature (Automotive E grade) | TA | -40 | 125 | °C | Automotive (E); VCC = +2.5V to +5.5V | 2 | |
| High-level input voltage | VIH | 0.7 | VCC | 2 | |||
| Low-level input voltage | VIL | 0.3 | VCC | 0.2 VCC for VCC < 2.5V | 2 | ||
| Hysteresis of Schmitt Trigger inputs | VHYS | 0.05 | VCC | (Note) | 2 | ||
| Low-level output voltage | VOL | 0.4 | V | IOL = 3.0 mA, VCC = 2.5V | 2 | ||
| Input leakage current | ILI | -1 | 1 | µA | VIN = VSS or VCC | 2 | |
| Output leakage current | ILO | -1 | 1 | µA | VOUT = VSS or VCC | 2 | |
| Pin capacitance (all inputs/outputs) | CIN, COUT | 10 | pF | VCC = 5.5V (Note); TA = 25°C, FCLK = 1 MHz | 2 | ||
| Operating current, write | ICC write | 0.1 | 3 | mA | VCC = 5.5V, SCL = 400 kHz | 2 | |
| Operating current, read | ICC read | 0.05 | 1 | mA | 2 | ||
| Standby current (Automotive) | ICCS | 5 | µA | Automotive; SDA = SCL = VCC; A0, A1, A2, WP = VSS | 2 | ||
| Clock frequency | FCLK | 400 | kHz | 1.8V ≤ VCC ≤ 5.5V | 3 | ||
| Clock high time | THIGH | 600 | ns | 1.8V ≤ VCC ≤ 5.5V | 3 | ||
| Clock low time | TLOW | 1300 | ns | 1.8V ≤ VCC ≤ 5.5V | 3 | ||
| SDA and SCL rise time | TR | 300 | ns | 1.8V ≤ VCC ≤ 5.5V (Note 1) | 3 | ||
| SDA and SCL fall time | TF | 300 | ns | 1.8V ≤ VCC ≤ 5.5V (Note 1) | 3 | ||
| Start condition hold time | THD:STA | 600 | ns | 1.8V ≤ VCC ≤ 5.5V | 3 | ||
| Start condition setup time | TSU:STA | 600 | ns | 1.8V ≤ VCC ≤ 5.5V | 3 | ||
| Data input hold time | THD:DAT | 0 | ns | (Note 2) | 3 | ||
| Data input setup time | TSU:DAT | 100 | ns | 1.8V ≤ VCC ≤ 5.5V | 3 | ||
| Stop condition setup time | TSU:STO | 600 | ns | 1.8V ≤ VCC ≤ 5.5V | 3 | ||
| WP setup time | TSU:WP | 600 | ns | 1.8V ≤ VCC ≤ 5.5V | 3 | ||
| WP hold time | THD:WP | 600 | ns | 1.8V ≤ VCC ≤ 5.5V | 3 | ||
| Output valid from clock | TAA | 900 | ns | 1.8V ≤ VCC ≤ 5.5V (Note 2) | 3 | ||
| Bus free time | TBUF | 4700 | ns | 1.8V ≤ VCC ≤ 5.5V | 3 | ||
| Input filter spike suppression (SDA and SCL pins) | TSP | 50 | ns | (Note 1 and Note 3) | 3 | ||
| Write cycle time (byte or page) | TWC | 5 | ms | 3 | |||
| Endurance | 1 | M cycles | 25°C, VCC = 5.5V, Block mode (Note 4) | 3 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | P = Plastic DIP, (300 mil Body), 8-lead SN = Plastic SOIC, (3.90 mm Body) | 27 |
CAD (KiCad official)
- Symbol:
24LC024T-E - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files:
24lc024t-e-etched.step/24lc024t-e-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);24lc024t-e.step/24lc024t-e.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (30 pp, sha256
11fe37a6615872bd, retrieved 2026-10-29, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).