3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownMAX3799ETJ+T
Maxim Integrated · Laser Drivers · TQFN-32(5x5)
MAX3799ETJ+T from Maxim Integrated, in a TQFN-32(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | LOS | output | Loss-of-signal open-drain output that defaults to high when the input is below the SET_LOS DAC threshold; polarity is invertible with LOS_POL = 0 and the function is disabled with LOS_EN = 0. |
| 2 | RSEL | input | TTL/CMOS mode-select input where logic-high selects high-bandwidth mode and logic-low selects high-gain mode, internally pulled down by a 75k resistor. |
| 3 | VCCR | power_in | Power supply for the receiver block. |
| 4 | ROUT+ | output | Noninverted CML receive data output, back-terminated for 50Ω. |
| 5 | ROUT- | output | Inverted CML receive data output, back-terminated for 50Ω. |
| 6 | VCCR | power_in | Power supply for the receiver block. |
| 7 | VCCD | power_in | Power supply for the digital block. |
| 8 | DISABLE | input | TTL/CMOS transmitter disable input; logic-low for normal operation, while logic-high or open disables modulation and bias current, internally pulled up by 8k to VCCT. |
| 9 | SCL | input | TTL/CMOS serial-clock input for the 3-wire interface, with a 75k internal pulldown. |
| 10 | SDA | bidirectional | TTL/CMOS serial-data line, open-drain output; requires an external 4.7k pullup to meet the 3-wire digital timing specification. |
| 11 | CSEL | input | TTL/CMOS chip-select input; logic-high starts a cycle and logic-low ends it and resets the control state machine, internally pulled down by a 75k resistor. |
| 12 | VCCT | power_in | Power supply for the transmitter block. |
| 13 | TIN+ | input | Noninverted CML transmit data input. |
| 14 | TIN- | input | Inverted CML transmit data input. |
| 15 | VCCT | power_in | Power supply for the transmitter block. |
| 16 | BMON | output | Bias current monitor output; current out of this pin develops a ground-referenced voltage across an external resistor proportional to the laser bias current. |
| 17 | VEET | power_in | Ground for the transmitter block. |
| 18 | VCCT | power_in | Power supply for the transmitter block. |
| 19 | TOUT- | output | Inverted modulation current output, back-terminated by 50Ω to VCCT. |
| 20 | TOUT+ | output | Noninverted modulation current output, back-terminated by 50Ω to VCCT. |
| 21 | VCCT | power_in | Power supply for the transmitter block. |
| 22 | BIAS | output | VCSEL bias current output. |
| 23 | FAULT | output | Transmitter fault open-drain output; logic-high indicates a fault, which remains high after the fault is removed until the fault latch is cleared by the DISABLE signal. |
| 24 | VCCT | power_in | Power supply for the transmitter block. |
| 25 | VCCT | power_in | Power supply for the transmitter block. |
| 26 | VEER | power_in | Ground for the receiver block. |
| 27 | VCCR | power_in | Power supply for the receiver block. |
| 28 | RIN- | input | Inverted CML receive data input. |
| 29 | RIN+ | input | Noninverted CML receive data input. |
| 30 | VCCR | power_in | Power supply for the receiver block. |
| 31 | CAZ2 | passive | Offset correction loop capacitor pin; a capacitor between CAZ2 and CAZ1 sets the loop time constant, and offset correction is disabled with AZ_EN = 0. |
| 32 | CAZ1 | passive | Offset correction loop capacitor pin, counterpart to CAZ2, internally connected to VEER. |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Maxim Integrated |
| Package | TQFN-32(5x5) |
| Category | Power Supply Chip |
| Pins | 33 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating ambient temperature (part temperature range) | TA | -40 | 85 | °C | MAX3799ETJ+ PART TEMP RANGE; electrical table TA = -40°C to +85°C | 2 | |
| Power-supply voltage | VCC | 2.85 | 3.63 | V | 2 | ||
| Supply voltage VCCR, VCCT, VCCD | VCCR, VCCT, VCCD | -0.3 | 4 | V | 2 | ||
| Voltage range at DISABLE, SDA, SCL, CSEL, RSEL, FAULT, BMON, LOS, CAZ2 (upper limit VCC + 0.3V) | -0.3 | V | Maximum printed as VCC + 0.3V | 2 | |||
| Voltage at BIAS (upper limit VCC) | 0 | V | Maximum printed as VCC | 2 | |||
| Current range into FAULT, LOS | -1 | 5 | mA | 2 | |||
| Current range into SDA | -1 | 1 | mA | 2 | |||
| Current into ROUT+, ROUT- | 40 | mA | 2 | ||||
| Current into TOUT+, TOUT- | 60 | mA | 2 | ||||
| Operating junction temperature range | -55 | 150 | °C | 2 | |||
| Storage temperature range | -65 | 160 | °C | 2 | |||
| Lead temperature (soldering) | 300 | °C | soldering, 10s | 2 | |||
| Soldering temperature (reflow) | 260 | °C | 2 | ||||
| High POR threshold | 2.55 | 2.75 | V | 2 | |||
| Low POR threshold | 2.3 | 2.45 | V | IBIAS = IBIASOFF and IMOD = IMODOFF | 2 | ||
| Power-supply current | ICC | 97 | 150 | mA | Includes the CML output current; excludes IBIAS = 6mA, IMOD = 6mA, VDIFF_ROUT = 400mVP-P (Note 1) | 2 | |
| Input data rate | 1.0625 | 10.32 | Gbps | 2 | |||
| Differential input resistance RIN+/RIN- | RIN_DIFF | 75 | 100 | 125 | Ω | RIN+/RIN- | 2 |
| Input sensitivity | VINMIN | 1 | 3 | mVP-P | RATE_SEL = 0 (1.25Gbps) | 2 | |
| Input sensitivity | VINMIN | 3 | 8 | mVP-P | RATE_SEL = 1 (10.32Gbps) | 2 | |
| Input overload | VINMAX | 1.2 | VP-P | 2 | |||
| Input return loss SDD11 | SDD11 | 14 | dB | DUT is powered on, f ≤ 5GHz | 2 | ||
| Input return loss SDD11 | SDD11 | 7 | dB | DUT is powered on, f ≤ 16GHz | 2 | ||
| Input return loss SCC11 | SCC11 | 8 | dB | DUT is powered on, 1GHz < f ≤ 5GHz | 2 | ||
| Differential output resistance | ROUTDIFF | 75 | 100 | 125 | Ω | 2 | |
| CML differential output voltage High | 595 | 800 | 1005 | mVP-P | 5mVP-P ≤ VIN ≤ 1200mVP-P, SET_CML[162] | 3 | |
| CML differential output voltage Medium | 300 | 400 | 515 | mVP-P | 10mVP-P ≤ VIN ≤ 1200mVP-P, SET_CML[80] | 3 | |
| Differential output signal when disabled | 6 | 15 | mVP-P | Outputs AC-coupled, VINMAX applied to input, VDIFF_ROUT = 800mVP-P at 8.5Gbps (Notes 2, 3) | 3 | ||
| Data output transition time (20% to 80%) | tR/tF | 26 | 35 | ps | 10mVP-P ≤ VIN ≤ 1200mVP-P, RATE_SEL = 1, VDIFF_ROUT = 400mVP-P (Notes 2, 3, 4) | 3 | |
| Data output transition time (20% to 80%) | tR/tF | 60 | 100 | ps | 5mVP-P ≤ VIN ≤ 1200mVP-P, RATE_SEL = 0, VDIFF_ROUT = 800mVP-P | 3 | |
| Deterministic jitter | DJ | 4 | 12 | psP-P | 60mVP-P ≤ VIN ≤ 400mVP-P at 10.32Gbps, RATE_SEL = 1, VDIFF_ROUT = 400mVP-P (Notes 2, 3, 5) | 3 | |
| Deterministic jitter | DJ | 20 | psP-P | 5mVP-P ≤ VIN ≤ 1200mVP-P at 1.25Gbps, RATE_SEL = 0, VDIFF_ROUT = 800mVP-P | 3 | ||
| Random jitter | RJ | 1.8 | 2.5 | psRMS | Input = 60mVP-P at 1.25Gbps, RATE_SEL = 0, VDIFF_ROUT = 800mVP-P | 3 | |
| Random jitter | RJ | 0.32 | 0.48 | psRMS | Input = 60mVP-P at 8.5Gbps, RATE_SEL = 1, VDIFF_ROUT = 400mVP-P | 3 | |
| LOS assert sensitivity range | 14 | 77 | mVP-P | 3 | |||
| LOS hysteresis | 1.25 | 2.1 | dB | 10 x log(VDEASSERT/VASSERT) (Note 6) | 3 | ||
| LOS assert/deassert time | 2.3 | 80 | µs | Note 7 | 3 | ||
| Low assert level | 8 | 11 | 14 | mVP-P | SET_LOS[7] (Notes 2, 6) | 3 | |
| Low deassert level | 14 | 18 | 21 | mVP-P | SET_LOS[7] (Notes 2, 6) | 3 | |
| Medium assert level | 39 | 48 | 58 | mVP-P | SET_LOS[32] (Notes 2, 6) | 3 | |
| Medium deassert level | 65 | 81 | 95 | mVP-P | SET_LOS[32] (Notes 2, 6) | 3 | |
| High assert level | 77 | 94 | 112 | mVP-P | SET_LOS[63] (Notes 2, 6) | 3 | |
| High deassert level | 127 | 158 | 182 | mVP-P | SET_LOS[63] (Notes 2, 6) | 3 | |
| Tx differential input voltage | VIN | 0.2 | 2.4 | VP-P | Data rate = 1.0625Gbps | 4 | |
| Tx differential input voltage | VIN | 0.075 | 0.8 | VP-P | Data rate = 10.32Gbps | 4 | |
| Common-mode input voltage | VINCM | 2.75 | V | 4 | |||
| Differential input resistance (Tx) | RIN | 75 | 100 | 125 | Ω | 4 | |
| Maximum modulation-on current into 100Ω differential load | IMODMAX | 12 | mA | Outputs AC-coupled, VCCTO 2.95V | 4 | ||
| Minimum modulation-on current into 100Ω differential load | IMODMIN | 2 | mA | Outputs AC-coupled | 4 | ||
| Maximum bias-on current | IBIASMAX | 15 | mA | Current into BIAS pin | 4 | ||
| Minimum bias-on current | IBIASMIN | 2 | mA | Current into BIAS pin | 4 | ||
| Compliance voltage at BIAS | VBIAS | 0.9 | 2.1 | V | 5 | ||
| Compliance voltage at BMON | VBMON | 0 | 1.8 | V | 5 | ||
| Excessive voltage at BIAS | VBIAS | 0.44 | 0.48 | 0.65 | V | Average voltage, FAULT always occurs for VBIAS 0.44V, FAULT never occurs for VBIAS 0.65V | 5 |
| Maximum VCSEL current in off state | IOFF | 25 | µA | FAULT or DISABLE, VBIAS = VCC | 5 | ||
| DISABLE assert time | t_OFF | 1 | µs | Time from rising edge of DISABLE input signal to IBIAS = IBIASOFF and IMOD = IMODOFF | 5 | ||
| DISABLE negate time | t_ON | 500 | µs | Time from falling edge of DISABLE to IBIAS and IMOD at 90% of steady state when FAULT = 0 before reset | 5 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | PIN NAME FUNCTION 14 TIN- Inverted Transmit Data Input, CML | 14 |
CAD (KiCad official)
- Symbol:
MAX3799ETJ+T - Footprint:
Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm - 3D model: TQFN-32(5x5) (KiCad packages3D, STEP)
- 3D model files:
max3799etj-t-etched.step/max3799etj-t-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);max3799etj-t.step/max3799etj-t.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Maxim Integrated datasheet (36 pp, sha256
1b82f6725275e6be, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).