component
HT7183STNR
Public Made by Adomby adom
Jiaxing Heroic Elec Tech DC-DC Converters, SOT-23-6. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownHT7183STNR
Jiaxing Heroic Elec Tech · DC-DC Converters · SOT-23-6
HT7183STNR from Jiaxing Heroic Elec Tech, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | power_out | Switching node of the converter, connected to the internal power switch (RDS(on) 120 mΩ); the absolute maximum rating on SW is -0.3 V to 20 V, and the inductor should be placed as close as possible to this pin. |
| 2 | GND | power_in | Ground reference for the device; the thermal pad must be soldered to a large ground plane with thermal vias, and the input and output capacitors should be connected to it with low impedance. |
| 3 | FB | input | Voltage feedback input with a 0.6 V reference, where VOUT = 0.6 V × (1 + RUP/RDN) and the RUP/RDN divider should sit as close as possible to this pin; the absolute maximum rating on FB is -0.3 V to 6 V. |
| 4 | EN | input | Enable logic input where a logic high above 1.8 V enables the device and a logic low below 0.6 V puts it into shutdown; it has an internal 800 kΩ pull-down and an absolute maximum rating of -0.3 V to 6 V. |
| 5 | VCC | power_in | Power supply input with a recommended range of 2.6 V to 5.5 V and an absolute maximum of 6 V; the UVLO threshold is 2.4 V rising and 2.2 V falling. |
| 6 | OC | input | Adjustable peak switch current limit, set by a resistor from this pin to GND, with the limit to be kept below 3 A for the SOT23-6 package. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Jiaxing Heroic Elec Tech |
| Package | SOT-23-6 |
| Category | Power Management (PMIC) |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Voltage range (VCC) | VCC | -0.3 | 6 | V | 5 | ||
| Voltage range (SW) | SW | -0.3 | 20 | V | 5 | ||
| Voltage range (EN, FB) | EN, FB | -0.3 | 6 | V | 5 | ||
| Operating temperature range | TA | -40 | 85 | ℃ | 5 | ||
| Operating junction temperature range | TJ | -40 | 150 | ℃ | 5 | ||
| Storage temperature range | TSTG | -50 | 150 | ℃ | 5 | ||
| Supply voltage range | VCC | 2.6 | 5.5 | V | 5 | ||
| Operating temperature | Ta | -40 | 25 | 85 | ℃ | 5 | |
| Operating junction temperature | TJ | -40 | 125 | ℃ | 5 | ||
| Power voltage range | VCC | 2.6 | 5.5 | V | Ta = 25ºC, VIN = 2.6V-5.5V, VOUT=4.5-13.2V, unless otherwise specified | 5 | |
| Under-voltage lockout (UVLO) threshold, rising | VUVLO | 2.4 | V | Rising | 5 | ||
| Under-voltage lockout (UVLO) threshold, falling | VUVLO | 2.2 | V | Falling | 5 | ||
| Quiescent current | IQ | 0.3 | mA | VFB = 1.3V, No switching | 5 | ||
| Shutdown current | ISD | 0.1 | uA | IC disabled, no load, no feedback resistor divider | 5 | ||
| Reference voltage at the FB pin | VREF | 0.6 | V | 5 | |||
| Output overvoltage protection | VOVP | 20 | V | 5 | |||
| EN high threshold voltage | VENH | 1.8 | V | 5 | |||
| EN low threshold voltage | VENL | 0.6 | V | 5 | |||
| EN internal pull-down resistance | REN | 800 | kΩ | 5 | |||
| MOSFET on-resistance | RDS(on) | 120 | mΩ | Including wire bond | 5 | ||
| Operation frequency | Fosc | 800 | kHz | 5 | |||
| Peak switch current limit | ILIM | 3 | A | SOT23-6 | 5 | ||
| Thermal shutdown threshold | TSD | 150 | ℃ | 6 | |||
| Thermal shutdown hysteresis | TSD_HYS | 20 | ℃ | 6 |
CAD (KiCad official)
- Symbol:
HT7183STNR - Footprint:
Package_TO_SOT_SMD:SOT-23-6 - 3D model: SOT-23-6 (KiCad packages3D, STEP)
- 3D model files:
ht7183stnr-etched.step/ht7183stnr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ht7183stnr.step/ht7183stnr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Jiaxing Heroic Elec Tech datasheet (16 pp, sha256
4b3565d3f72e0da9, retrieved 2026-10-18, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).