3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownTD1660
Techcode Semicon · DC-DC Converters · ESOP-8
TD1660 from Techcode Semicon, in a ESOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | output | Switch node. Output from the internal high-side power MOSFET (RDS(ON) typ 250mΩ). Requires a low-VF Schottky rectifier to ground placed close to the pin to reduce switching spikes. Absolute max: -0.5V to VIN+0.5V. |
| 2 | EN | input | Enable input (positive logic). Pull above rising threshold (typ 1.5V, spec 1.3V-2.2V) or leave floating to enable; pull below falling threshold (~1.2V) to shut down. 200mV hysteresis. Absolute max: -0.3V to +5V. |
| 3 | COMP | output | Compensation node. Output of the internal Gm error amplifier; connect an external series R-C (and optional second cap) to set loop pole/zero. COMP is clamped internally between 0.9V and 2.0V; do not drive above 2.6V. |
| 4 | FB | input | Feedback input to the error amplifier. Connect a resistive divider from VOUT to GND; the divider node is compared to the internal 0.8V reference (0.780V-0.820V) to set the regulated output voltage (0.8V to 52V). |
| 5 | GND | power_in | Ground return. Also the exposed thermal pad on the ESOP-8 package - connect to the GND plane for optimal thermal performance. Route close to the output capacitor and away from high-current switch paths. |
| 6 | FREQ | input | Switching-frequency program input. Connect a resistor RFREQ from this pin to GND to set the oscillator frequency, per RFREQ(kΩ) = 100000/fS(kHz) − 5 (e.g. 195kΩ → 500kHz; 150kΩ → ~700kHz). Programmable up to 1MHz. |
| 7 | VIN | power_in | Input supply, 9V to 60V (abs max 60V). Powers the internal control circuitry, bootstrap regulator, and high-side power MOSFET. UVLO rising threshold typ 7.2V (0.5V hysteresis). Place a decoupling capacitor to GND close to this pin. |
| 8 | BST | power_in | Bootstrap. Positive supply for the internal floating high-side MOSFET driver. Connect a bypass capacitor (typ 0.1μF) between BST and SW; internally regulated to ~5V above SW. BST-to-SW abs max +5V. |
| 9 | GND | power_in | Exposed pad; the maker lists it with pin 5 ("5 GND, Exposed pad ... Connect exposed pad to GND plane for optimal thermal performance"). KiCad's SOIC-8-1EP numbers the exposed pad 9. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Techcode Semicon |
| Package | ESOP-8 |
| Category | DC-DC Converters |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage (VIN) | VIN | -0.3 | 60 | V | 4 | ||
| Switch Voltage | VSW | -0.5 | V | 4 | |||
| BST to SW | -0.3 | 5 | V | 4 | |||
| All other pins | -0.3 | 5 | V | 4 | |||
| Junction Temperature | TJ | 150 | ºC | 4 | |||
| Maximum Lead Soldering Temperature | TSDR | 260 | ºC | 10 seconds | 4 | ||
| VIN Supply Voltage (recommended) | VIN | 9 | 60 | V | 4 | ||
| Converter Output Voltage | VOUT | 0.8 | 52 | V | 4 | ||
| Operating Junction Temperature | TJ | -40 | 125 | °C | 4 | ||
| Feedback Voltage | VFB | 0.78 | 0.8 | 0.82 | V | 9V < VIN < 60V | 4 |
| Top Switch RDS(ON) | RDS(ON)-T | 175 | 250 | 330 | mΩ | VBST, VSW = 5V | 4 |
| Current Limit | 2.2 | 4.7 | A | 4 | |||
| Oscillator Frequency | 0.6 | 0.8 | MHz | RFREQ = 150kΩ | 4 | ||
| Shutdown Supply Current | 1 | 3 | μA | VEN < 0.3V | 4 | ||
| EN Up Threshold | 1.3 | 2.2 | V | 5 | |||
| Top Switch Leakage Current | 1 | μA | VEN = 0V, VSW = 0V | 4 | |||
| COMP to Current Sense Transconductance | GCS | 5.7 | A/V | 4 | |||
| Error Amp Voltage Gain | 400 | V/V | 4 | ||||
| Error Amp Transconductance | 120 | μA/A | ICOMP = ±3μA | 4 | |||
| Error Amp Min Source Current | 10 | μA | VFB = 0.7V | 4 | |||
| Error Amp Min Sink Current | -10 | μA | VFB = 0.9V | 4 | |||
| VIN UVLO Threshold | 7.2 | V | 4 | ||||
| VIN UVLO Hysteresis | 0.5 | V | 4 | ||||
| Soft-Start Time | 0.5 | ms | 0V < VFB < 0.8V | 4 | |||
| Minimum Switch On Time | 100 | ns | 4 | ||||
| Quiescent Supply Current | 180 | μA | No load, VFB = 0.9V | 5 | |||
| Thermal Shutdown Hysteresis | 150 | °C | Hysteresis = 20°C | 5 | |||
| Minimum Off Time | 100 | ns | 5 | ||||
| Minimum On Time | 100 | ns | 5 | ||||
| EN Threshold Hysteresis | 200 | mV | 5 |
CAD (KiCad official)
- Symbol:
TD1660 - Footprint:
Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm - 3D model: ESOP-8 (KiCad packages3D, STEP)
- 3D model files:
td1660-etched.step/td1660-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);td1660.step/td1660.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Techcode Semicon datasheet (13 pp, sha256
67a24a62ca900eb4, retrieved 2026-11-16, tier: manufacturer) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).