Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

NCP707CMX300TCG

onsemi · Linear Voltage Regulators (LDO) · XDFN-4-EP(1x1)

NCP707CMX300TCG from onsemi, in a XDFN-4-EP(1x1). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 OUT power_out Regulated output voltage pin; a small ceramic capacitor with a minimum value of 1 µF is needed from this pin to ground to assure stability.
2 GND power_in Power supply ground.
3 EN input Driving EN above 0.9 V turns on the regulator and driving EN below 0.4 V puts the regulator into shutdown mode.
4 IN power_in Input pin; a small 1 µF capacitor is needed from this pin to ground to assure stability.
5 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer onsemi
Package XDFN-4-EP(1x1)
Category Power Supply Chip
Pins 5

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Operating Input Voltage VIN 1.8 5.5 V 3
Output Voltage Accuracy VOUT -2 2 % VOUT + 0.5 V ≤ VIN ≤ 5.5 V, IOUT = 0 − 200 mA 3
Line Regulation RegLINE 400 V/V VOUT + 0.5 V ≤ VIN ≤ 5.5 V, IOUT = 10 mA 3
Load Regulation RegLOAD 10 V/mA IOUT = 0 mA to 200 mA 3
Load Transient TranLOAD 75 mV IOUT = 1 mA to 200 mA or 200 mA to 1 mA in 1 s, COUT = 1 F 3
Dropout Voltage VDO 111 165 mV IOUT = 200 mA, VOUT = 3.0 V 3
Output Current Limit ICL 250 379 500 mA VOUT = 90% VOUT(nom) 3
Ground Current IQ 25 35 µA IOUT = 0 mA 3
Shutdown Current IDIS 0.01 1 µA VEN ≤ 0.4 V, VIN = 5.5 V 3
EN Pin Threshold Voltage, High VEN_HI 0.9 V VEN voltage increasing 3
EN Pin Threshold Voltage, Low VEN_LO 0.4 V VEN voltage decreasing 3
EN Pin Input Current IEN 180 500 nA VEN = 5.5 V 3
Ground Current IGND 105 µA IOUT = 2 mA 3
Ground Current IGND 240 µA IOUT = 200 mA 3
Turn-on Time tON 200 µs COUT = 1.0 µF, from assertion of VEN to 98% VOUT(NOM) 3
Power Supply Rejection Ratio at 100 Hz PSRR 58 dB VIN = 3.6 V, VOUT = 3.1 V, IOUT = 150 mA, f = 100 Hz 3
Power Supply Rejection Ratio at 1 kHz PSRR 70 dB VIN = 3.6 V, VOUT = 3.1 V, IOUT = 150 mA, f = 1 kHz 3
Power Supply Rejection Ratio at 10 kHz PSRR 55 dB VIN = 3.6 V, VOUT = 3.1 V, IOUT = 150 mA, f = 10 kHz 3
Output Noise Voltage VN 22 Vrms VOUT = 3.1 V, VIN = 3.6 V, IOUT = 200 mA, f = 100 Hz to 100 kHz 3
Thermal Shutdown Temperature TSD 160 °C Temperature increasing from TJ = +25°C 3
Thermal Shutdown Hysteresis TSDH 20 °C Temperature falling from TSD 3
Active Output Discharge Resistance (Version C) RDIS 120 Ω VEN < 0.4 V, Version C only 3
Input Voltage (absolute maximum) VIN -0.3 6 V 2
Output Voltage (absolute maximum) VOUT -0.3 V Upper limit printed as VIN + 0.3 V 2
Enable Input Voltage (absolute maximum) VEN -0.3 V Upper limit printed as VIN + 0.3 V 2
Maximum Junction Temperature TJ(MAX) 150 °C 2
Storage Temperature TSTG -55 150 °C 2
Operating Junction Temperature TJ -40 125 °C −40°C ≤ TJ ≤ 125°C 3
Thermal Resistance, Junction-to-Air (XDFN4 1x1 mm) RJA 250 °C/W Single component mounted on 2 oz FR4 PCB with 100 mm² Cu area 2

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper 4 IN Input pin. A small 1 F capacitor is needed from this pin to ground to assure stability. − EPAD Exposed pad should be connected directly to the GND pin. Soldered to a large ground copper plane all 2

CAD (KiCad official)

  • Symbol: NCP707CMX300TCG
  • Footprint: Package_DFN_QFN:OnSemi_XDFN4-1EP_1.0x1.0mm_EP0.52x0.52mm
  • 3D model: XDFN-4-EP(1x1) (KiCad packages3D, STEP)
  • 3D model files: ncp707cmx300tcg-etched.step / ncp707cmx300tcg-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ncp707cmx300tcg.step / ncp707cmx300tcg.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: onsemi datasheet (19 pp, sha256 7d73bc0816b7d56e, retrieved 2026-10-28, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF