Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MCP1612T-ADJI

Microchip Tech · DC-DC Converters · MSOP-8

MCP1612T-ADJI from Microchip Tech, in a MSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VIN power_in Input voltage pin, operating from 2.7V to 5.5V, with a 10 µF bypass capacitor connected between VIN and PGND.
2 VCC power_in Analog input voltage pin that biases internal analog functions, derived by filtering the VIN supply (10 Ω resistor from VIN and 0.1 µF capacitor to ground recommended).
3 SHDN input Shutdown control input where logic-high (>45% of VIN) enables the regulator and logic-low (<15% of VIN) forces shutdown with both switches off.
4 COMP output Transconductance error amplifier output pin where the external RC compensation network is connected for control-loop stabilization.
5 FB input Feedback input connected to the output through an external resistor divider, with a nominal regulation voltage of 0.8V.
6 AGND power_in Analog ground pin to which all small-signal ground returns are tied.
7 PGND power_in Power ground pin for all large-signal ground returns, kept to a small loop area and length to limit switching noise coupling.
8 LX output Buck inductor output (switch node) pin connected directly to the inductor, carrying large signal-level currents with short connections.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package MSOP-8
Category Power Supply Chip
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input Operating Voltage VIN 2.7 5.5 V 4
Input Shutdown Current I(VIN) 0.01 1 µA Shutdown mode (SHDN = GND) 4
Input Quiescent Current I(VIN) 5 7 mA ILOAD = 0 mA 4
Internal Oscillator Frequency FOSC 1.2 1.4 1.6 MHz 4
LX Pin Leakage Current ILX -1 1 µA SHDN = 0V, VIN = 5.5V, LX = 0V, LX = 5.5V 4
Transconductance from FB to COMP gm 35 62 90 µA/V 4
Output Voltage Range VOUT 0.8 V Upper limit printed as VIN 4
Reference Feedback Voltage VFB 0.78 0.8 0.82 V 4
Line Regulation VLINE-REG 0.15 0.5 %/V VIN = 2.7V to 5.5V, ILOAD = 100 mA 4
Undervoltage Lockout UVLO 2.4 2.55 2.7 V Note 2 5
Logic-High Input (SHDN) VIN-HIGH 45 % of VIN 5
Logic-Low Input (SHDN) VIN-LOW 15 % of VIN 5
Storage Temperature Range TA -65 150 °C Continuous 5
Maximum Junction Temperature TJ 150 °C Transient Only 5
Operating Junction Temperature Range TA -40 125 °C Continuous Operation 5
Absolute Max LX to PGND LX -0.3 V -0.3V to (VIN + 0.3V) 4
Absolute Max PGND to AGND PGND to AGND -0.3 0.3 V 4
Absolute Max Storage Temperature -65 150 °C 4
Absolute Max Ambient Temp. with Power Applied -40 85 °C 4
Absolute Max Operating Junction Temperature -40 125 °C 4
RDSon P-Channel RDSon-P 300 mΩ IP = 250 mA 4
RDSon N-Channel RDSon-N 300 mΩ IN = 250 mA 4
Positive Current Limit Threshold +ILX(MAX) 2.3 A 4
Negative Current Limit Threshold -ILX(MAX) -1.4 A 4
Feedback Input Bias Current IVFB 1 nA 4
Load Regulation VLOAD-REG 0.25 % VIN = 4.2V, ILOAD = 100 mA to 1A 4
Undervoltage Lockout Hysteresis UVLO-HYS 200 mV 5
Thermal Shutdown TSHD 160 °C Note 1 5
Thermal Shutdown Hysteresis TSHD-HYS 9 °C 5
Thermal Resistance, 8L-MSOP θJA 208 °C/W Typical 4-layer board interconnecting vias 5

CAD (KiCad official)

  • Symbol: MCP1612T-ADJI
  • Footprint: Package_SO:MSOP-8_3x3mm_P0.65mm
  • 3D model: MSOP-8 (KiCad packages3D, STEP)
  • 3D model files: mcp1612t-adji-etched.step / mcp1612t-adji-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mcp1612t-adji.step / mcp1612t-adji.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (22 pp, sha256 70dd4880465f0ab5, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF