component
F280041PZS
Public Made by Adomby adom
Texas Instruments Microcontroller Units (MCUs/MPUs/SOCs), LQFP-100(14x14). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownF280041PZS
Texas Instruments · Microcontroller Units (MCUs/MPUs/SOCs) · LQFP-100(14x14)
F280041PZS from Texas Instruments, in a LQFP-100(14x14). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GPIO28 | bidirectional | General-purpose I/O 28 with alternate functions including SCIA_RX, EPWM7_A and SD1_D3. |
| 2 | XRSn | bidirectional | Device reset input and watchdog reset output; open-drain with internal pull-up, requires a 2.2kΩ to 10kΩ resistor to VDDIO. |
| 3 | VDDIO | power_in | 3.3V digital I/O supply pin; place a decoupling capacitor of at least 0.1µF on each VDDIO pin. |
| 4 | VDD | power_in | 1.2V digital logic supply pin; TI recommends a total decoupling capacitance of about 20µF near the VDD pins. |
| 5 | VSS | power_in | Digital ground pin that must be connected to the board ground. |
| 6 | A6/PGA5_OF | input | ADC-A analog input 6 that is also the optional PGA-5 output filter node. |
| 7 | B2/C6/PGA3_OF | input | ADC-B analog input 2 multiplexed with ADC-C input 6 and the optional PGA-3 output filter node. |
| 8 | B3/VDAC | input | ADC-B analog input 3 and optional external reference for the on-chip DAC; requires a 1µF capacitor if used as the DAC reference. |
| 9 | A2/B6/PGA1_OF | input | ADC-A analog input 2 multiplexed with ADC-B input 6 and the optional PGA-1 output filter node. |
| 10 | A3 | input | ADC-A analog input 3 that also serves as a CMPSS-1 comparator input. |
| 11 | VDDA | power_in | 3.3V analog supply pin; place a decoupling capacitor of at least 2.2µF to VSSA on each pin. |
| 12 | VSSA | power_in | Analog ground pin. |
| 13 | PGA5_GND | power_in | Kelvin ground reference for PGA-5 input. |
| 14 | PGA1_GND | power_in | Kelvin ground reference for PGA-1 input. |
| 15 | PGA3_GND | power_in | Kelvin ground reference for PGA-3 input. |
| 16 | PGA5_IN | input | Input of programmable gain amplifier PGA-5. |
| 17 | C4 | input | ADC-C analog input 4 that also serves as a CMPSS-5 comparator input. |
| 18 | PGA1_IN | input | Input of programmable gain amplifier PGA-1. |
| 19 | C0 | input | ADC-C analog input 0 that also serves as a CMPSS-1 comparator input. |
| 20 | PGA3_IN | input | Input of programmable gain amplifier PGA-3. |
| 21 | C2 | input | ADC-C analog input 2 that also serves as a CMPSS-3 comparator input. |
| 22 | A1/DACB_OUT | output | ADC-A analog input 1 multiplexed with the buffered DAC-B output. |
| 23 | A0/B15/C15/DACA_OUT | output | ADC-A analog input 0 multiplexed with ADC-B/ADC-C inputs and the buffered DAC-A output. |
| 24 | VREFHIB/VREFHIC | bidirectional | ADC-B and ADC-C high reference voltage; place at least 2.2µF between each and its matching VREFLO pin. |
| 25 | VREFHIA | bidirectional | ADC-A high reference voltage; place at least 2.2µF between this pin and VREFLOA. |
| 26 | VREFLOB/VREFLOC | input | ADC-B and ADC-C low reference voltage. |
| 27 | VREFLOA | input | ADC-A low reference voltage. |
| 28 | C5/PGA6_IN | input | ADC-C analog input 5 multiplexed with the input of PGA-6. |
| 29 | C1 | input | ADC-C analog input 1 that also serves as a CMPSS-2 comparator input. |
| 30 | PGA2_IN | input | Input of programmable gain amplifier PGA-2. |
| 31 | C3/PGA4_IN | input | ADC-C analog input 3 multiplexed with the input of PGA-4. |
| 32 | PGA2_GND/PGA4_GND/PGA6_GND | power_in | Shared Kelvin ground reference for PGA-2, PGA-4 and PGA-6. |
| 33 | VSSA | power_in | Analog ground pin. |
| 34 | VDDA | power_in | 3.3V analog supply pin; place a decoupling capacitor of at least 2.2µF to VSSA. |
| 35 | A5 | input | ADC-A analog input 5 that also serves as a CMPSS-2 comparator input. |
| 36 | A4/B8/PGA2_OF | input | ADC-A analog input 4 multiplexed with ADC-B input 8 and the optional PGA-2 output filter node. |
| 37 | A8/PGA6_OF | input | ADC-A analog input 8 multiplexed with the optional PGA-6 output filter node. |
| 38 | A9 | input | ADC-A analog input 9 that also serves as a CMPSS-6 comparator input. |
| 39 | B4/C8/PGA4_OF | input | ADC-B analog input 4 multiplexed with ADC-C input 8 and the optional PGA-4 output filter node. |
| 40 | A10/B1/C10/PGA7_OF | input | ADC-A analog input 10 multiplexed with ADC-B and ADC-C inputs and the optional PGA-7 output filter node. |
| 41 | B0 | input | ADC-B analog input 0 that also serves as a CMPSS-7 comparator input. |
| 42 | PGA7_GND | power_in | Kelvin ground reference for PGA-7 input. |
| 43 | PGA7_IN | input | Input of programmable gain amplifier PGA-7. |
| 44 | C14 | input | ADC-C analog input 14 that also serves as a CMPSS-7 comparator input. |
| 45 | VSS | power_in | Digital ground pin that must be connected to the board ground. |
| 46 | VDD | power_in | 1.2V digital logic supply pin; requires decoupling capacitors on each VDD pin. |
| 47 | VDDIO | power_in | 3.3V digital I/O supply pin; place a decoupling capacitor of at least 0.1µF on this pin. |
| 48 | FLT2 | unconnected | Flash test pin 2 reserved by TI; must be left unconnected. |
| 49 | FLT1 | unconnected | Flash test pin 1 reserved by TI; must be left unconnected. |
| 50 | GPIO13 | bidirectional | General-purpose I/O 13 with alternate functions including EPWM7_B, CANB_RX and PMBUSA_ALERT. |
| 51 | GPIO12 | bidirectional | General-purpose I/O 12 with alternate functions including EPWM7_A, CANB_TX and SCIB_TX. |
| 52 | GPIO11 | bidirectional | General-purpose I/O 11 with alternate functions including EPWM6_B, SCIB_RX and SPIA_STE. |
| 53 | GPIO33 | bidirectional | General-purpose I/O 33 with alternate functions including I2CA_SCL, LINA_RX and CANA_RX. |
| 54 | GPIO16 | bidirectional | General-purpose I/O 16 with alternate functions including SPIA_SIMO, SCIA_TX and XCLKOUT. |
| 55 | GPIO17 | bidirectional | General-purpose I/O 17 with alternate functions including SPIA_SOMI, SCIA_RX and PMBUSA_SDA. |
| 56 | GPIO24 | bidirectional | General-purpose I/O 24 with alternate functions including EQEP2_A, SCIA_TX and ERRORSTS. |
| 57 | GPIO25 | bidirectional | General-purpose I/O 25 with alternate functions including EQEP2_B, SCIA_RX and FSITXA_D1. |
| 58 | GPIO26 | bidirectional | General-purpose I/O 26 with alternate functions including EQEP2_INDEX, SPIB_CLK and I2CA_SDA. |
| 59 | GPIO27 | bidirectional | General-purpose I/O 27 with alternate functions including EQEP2_STROBE, SPIB_STE and I2CA_SCL. |
| 60 | TCK | input | JTAG test clock input with an internal pull-up resistor. |
| 61 | GPIO37/TDO | output | JTAG test data output TDO by default; GPIO37 when reconfigured. TDO is tri-stated when no JTAG activity; enable pull-up or add external pull-up. |
| 62 | TMS | bidirectional | JTAG test mode select with internal pull-up; add an external 2.2kΩ pull-up to VDDIO recommended. |
| 63 | GPIO35/TDI | input | JTAG test data input TDI by default; GPIO35 when reconfigured. Enable internal pull-up or add external pull-up to avoid a floating input. |
| 64 | GPIO32 | bidirectional | General-purpose I/O 32 with alternate functions including I2CA_SDA, SPIB_CLK and FSIRXA_D0. |
| 65 | GPIO56 | bidirectional | General-purpose I/O 56 with alternate functions including SPIA_CLK, EQEP2_STROBE and SCIB_TX. |
| 66 | GPIO57 | bidirectional | General-purpose I/O 57 with alternate functions including SPIA_STE, EQEP2_INDEX and SCIB_RX. |
| 67 | GPIO58 | bidirectional | General-purpose I/O 58 with alternate functions including OUTPUTXBAR1, SPIB_CLK and LINA_TX. |
| 68 | GPIO18_X2 | bidirectional | General-purpose I/O 18 or crystal oscillator output X2; GPIO use requires INTOSC clocking and a 1kΩ pull-down on X1. |
| 69 | X1 | bidirectional | Crystal oscillator input or single-ended 3.3V clock input; must be configured by software before enabling the crystal oscillator. |
| 70 | VDDIO | power_in | 3.3V digital I/O supply pin; place a decoupling capacitor of at least 0.1µF on this pin. |
| 71 | VDD | power_in | 1.2V digital logic supply pin; requires decoupling capacitors on each VDD pin. |
| 72 | VSS | power_in | Digital ground pin that must be connected to the board ground. |
| 73 | VREGENZ | input | Internal regulator enable with internal pull-down; tie to VSS to enable the internal VREG and to VDDIO for external supply. |
| 74 | GPIO8 | bidirectional | General-purpose I/O 8 with alternate functions including EPWM5_A, SCIA_TX and SPIA_SIMO. |
| 75 | GPIO4 | bidirectional | General-purpose I/O 4 with alternate functions including EPWM3_A, CANA_TX and FSIRXA_CLK. |
| 76 | GPIO3 | bidirectional | General-purpose I/O 3 with alternate functions including EPWM2_B, SPIA_CLK and SCIA_RX. |
| 77 | GPIO2 | bidirectional | General-purpose I/O 2 with alternate functions including EPWM2_A, OUTPUTXBAR1 and SCIA_TX. |
| 78 | GPIO1 | bidirectional | General-purpose I/O 1 with alternate functions including EPWM1_B and I2CA_SCL. |
| 79 | GPIO0 | bidirectional | General-purpose I/O 0 with alternate functions including EPWM1_A and I2CA_SDA. |
| 80 | VDDIO_SW | power_in | 3.3V supply for the internal DC-DC regulator; requires 20µF input capacitance and must be tied to VDDIO. |
| 81 | GPIO23_VSW | bidirectional | General-purpose I/O 23 by default configured as the DC-DC switching output VSW when the internal regulator is enabled. |
| 82 | VSS_SW | power_in | Internal DC-DC regulator ground; must be connected to VSS. |
| 83 | GPIO22_VFBSW | bidirectional | General-purpose I/O 22 by default configured as the DC-DC feedback input VFBSW; connect to the VDD rail near the device when used. |
| 84 | GPIO7 | bidirectional | General-purpose I/O 7 with alternate functions including EPWM4_B, CANB_RX and SPIB_SIMO. |
| 85 | GPIO40 | bidirectional | General-purpose I/O 40 with alternate functions including PMBUSA_SDA, FSIRXA_D0 and EQEP1_A. |
| 86 | VSS | power_in | Digital ground pin that must be connected to the board ground. |
| 87 | VDD | power_in | 1.2V digital logic supply pin; requires decoupling capacitors on each VDD pin. |
| 88 | VDDIO | power_in | 3.3V digital I/O supply pin; place a decoupling capacitor of at least 0.1µF on this pin. |
| 89 | GPIO5 | bidirectional | General-purpose I/O 5 with alternate functions including EPWM3_B, CANA_RX and SPIA_STE. |
| 90 | GPIO9 | bidirectional | General-purpose I/O 9 with alternate functions including EPWM5_B, SCIB_TX and SPIA_CLK. |
| 91 | GPIO39 | bidirectional | General-purpose I/O 39 with alternate functions including CANB_RX and FSIRXA_CLK. |
| 92 | GPIO59 | bidirectional | General-purpose I/O 59 with alternate functions including OUTPUTXBAR2, SPIB_STE and CANB_RX. |
| 93 | GPIO10 | bidirectional | General-purpose I/O 10 with alternate functions including EPWM6_A, CANB_RX and I2CA_SDA. |
| 94 | GPIO34 | bidirectional | General-purpose I/O 34 with alternate functions including OUTPUTXBAR1 and PMBUSA_SDA. |
| 95 | GPIO15 | bidirectional | General-purpose I/O 15 with alternate functions including EPWM8_B, SCIB_RX and SPIB_STE. |
| 96 | GPIO14 | bidirectional | General-purpose I/O 14 with alternate functions including EPWM8_A, SCIB_TX and SPIB_CLK. |
| 97 | GPIO6 | bidirectional | General-purpose I/O 6 with alternate functions including EPWM4_A, SYNCOUT and CANB_TX. |
| 98 | GPIO30 | bidirectional | General-purpose I/O 30 with alternate functions including CANA_RX, SPIB_SIMO and SD1_D4. |
| 99 | GPIO31 | bidirectional | General-purpose I/O 31 with alternate functions including CANA_TX, SPIB_SOMI and SD1_C4. |
| 100 | GPIO29 | bidirectional | General-purpose I/O 29 with alternate functions including SCIA_TX, EPWM7_B and LINA_RX. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | LQFP-100(14x14) |
| Category | Embedded Processors & Controllers |
| Pins | 100 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDDIO 电源电压 (以 VSS 为基准) | VDDIO | -0.3 | 4.6 | V | 以 VSS 为基准 | 58 | |
| VDDA 电源电压 (以 VSSA 为基准) | VDDA | -0.3 | 4.6 | V | 以 VSSA 为基准 | 58 | |
| VDD 电源电压 (以 VSS 为基准) | VDD | -0.3 | 1.5 | V | 以 VSS 为基准 | 58 | |
| VDDIO 和 VDDIO_SW 引脚之间的电压差 | -0.3 | 0.3 | V | 58 | |||
| 输入电压 (3.3V) | VIN | -0.3 | 4.6 | V | (3.3V) | 58 | |
| 输出电压 | VO | -0.3 | 4.6 | V | 58 | ||
| 数字输入钳位电流 (每引脚) | IIK | -20 | 20 | mA | VIN < VSS 或 VIN > VDDIO | 58 | |
| 模拟输入钳位电流 (每引脚) | IIKANALOG | -20 | 20 | mA | VIN < VSSA 或 VIN > VDDA | 58 | |
| 数字输出电流 (每引脚) | IOUT | -20 | 20 | mA | 58 | ||
| 自然通风温度 | TA | -40 | 125 | °C | 58 | ||
| 工作结温 | TJ | -40 | 150 | °C | 58 | ||
| 贮存温度 | Tstg | -65 | 150 | °C | 58 | ||
| 器件电源电压 VDDIO 和 VDDA (启用内部 BOR) | VDDIO/VDDA | 3.3 | 3.63 | V | 启用内部 BOR | 59 | |
| 器件电源电压 VDDIO 和 VDDA (禁用内部 BOR) | VDDIO/VDDA | 2.8 | 3.3 | 3.63 | V | 禁用内部 BOR | 59 |
| 器件电源电压 VDD | VDD | 1.14 | 1.2 | 1.32 | V | 59 | |
| 结温 TJ (S 版本) | TJ | -40 | 125 | °C | S 版本 | 59 | |
| 高电平输入电压 (3.3V) | VIH | 2 | V | (3.3V) | 67 | ||
| 低电平输入电压 (3.3V) | VIL | 0.8 | V | (3.3V) | 67 | ||
| VDDIO 欠压复位电压 | VBOR-VDDIO | 2.81 | 3 | V | 67 | ||
| VDDIO 欠压复位电压 (斜降时) | VBOR-VDDIO-DN | 2.81 | 3 | V | 斜降时, XRSn 释放之后 | 80 | |
| IDD 运行期间的 VDD 电流消耗 | IDD | 61 | 90 | mA | 工作模式, 典型值 Vnom 30℃, 请参阅节 6.5.4 | 61 | |
| IDDIO 运行期间的 VDDIO 电流消耗 | IDDIO | 26 | 45 | mA | 工作模式, 典型值 Vnom 30℃ | 61 | |
| IDDA 运行期间的 VDDA 电流消耗 | IDDA | 12 | 30 | mA | 工作模式, 典型值 Vnom 30℃ | 61 | |
| 器件处于空闲模式时的 VDD 电流消耗 | IDD | 18 | 40 | mA | 空闲模式, CPU 处于空闲模式, 闪存被断电, XCLKOUT 被关闭 | 61 | |
| 器件处于停机模式时的 VDD 电流消耗 | IDD | 0.9 | 20 | mA | 停机模式, CPU 处于停机模式, 闪存被断电, XCLKOUT 被关闭 | 61 | |
| 擦除/编程周期期间的 VDD 电流消耗 | IDD | 40 | 70 | mA | 闪存擦除/编程, SYSCLK 以 100MHz 运行 | 61 | |
| CL1、CL2 负载电容 | CL1, CL2 | 12 | 24 | pF | 94 | ||
| 晶振并联电容 | C0 | 7 | pF | 94 | |||
| fINTOSC 频率 (INTOSC1 和 INTOSC2) | fINTOSC | 9.7 | 10 | 10.3 | MHz | INTOSC1 和 INTOSC2 | 94 |
| 频率稳定性 | fINTOSC-STABILITY | -3 | 3 | % | 95 | ||
| ADCCLK (源自 PERx.SYSCLK) | ADCCLK | 5 | 50 | MHz | 123 | ||
| 采样率 | 3.45 | MSPS | 100MHz SYSCLK | 123 | |||
| 增益误差 (外部基准) | -5 | 5 | LSB | 外部基准 | 124 | ||
| 偏移量误差 | -5 | 5 | LSB | 124 | |||
| INL 误差 | INL | -2 | 2 | LSB | 124 | ||
| DNL 误差 | DNL | -1 | 1 | LSB | 124 | ||
| 缓冲 DAC 偏移量误差 (中点) | -10 | 10 | mV | 中点 | 136 | ||
| 缓冲 DAC 增益误差 | -2.5 | 2.5 | %FSR | 136 | |||
| 缓冲 DAC DNL (已更正端点) | DNL | -1 | 1 | LSB | 已更正端点 | 136 | |
| 缓冲 DAC INL (已更正端点) | INL | -5 | 5 | LSB | 已更正端点 | 136 | |
| 缓冲 DAC 有效输出电压范围下限 | VOUT | 0.3 | V | RL = 5kΩ | 136 | ||
| 比较器以输入为基准的偏移量误差 | -20 | 20 | mV | 低共模, 反相输入设置为 50mV | 143 | ||
| CMPSS DAC 静态偏移量误差 | -25 | 25 | mV | 144 | |||
| CMPSS DAC 静态增益误差 | -2 | 2 | FSR 百分比 | 144 | |||
| PMBus 有效低电平输入电压 | VIL | 0.8 | V | 176 | |||
| PMBus 有效高电平输入电压 | VIH | 2.1 | V | 176 | |||
| PMBus 快速模式 SCL 时钟频率 | fSCL | 10 | 400 | kHz | 176 | ||
| 结至外壳热阻 (PZ 封装) | RΘJC | 7.6 | °C/W | PZ 封装 | 68 | ||
| 结至电路板热阻 (PZ 封装) | RΘJB | 24.2 | °C/W | PZ 封装 | 68 | ||
| 结至大气热阻 (高 k PCB, PZ 封装) | RΘJA | 46.1 | °C/W | 气流 0 lfm | 68 | ||
| VDDIO 欠压复位电压 (VDDIO 中的 VBOR-VDDIO 典型) | VBOR-VDDIO | 3 | V | 67 | |||
| 内部稳压器输出 VVREG | VVREG | 1.2 | V | 内部 VREG 打开 | 67 | ||
| 内部开关稳压器输出 VDC-DC | VDC-DC | 1.2 | V | 内部直流/直流打开 | 67 |
CAD (KiCad official)
- Symbol:
F280041PZS - Footprint:
Package_QFP:LQFP-100_14x14mm_P0.5mm - 3D model: LQFP-100(14x14) (KiCad packages3D, STEP)
- 3D model files:
f280041pzs-etched.step/f280041pzs-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);f280041pzs.step/f280041pzs.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (277 pp, sha256
867e7bb5ada6819c, retrieved 2026-11-02, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).