3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownLT1763CDE-5#TRPBF
Analog Devices · Linear Voltage Regulators (LDO) · DFN-12-EP(3x4)
LT1763CDE-5#TRPBF from Analog Devices, in a DFN-12-EP(3x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | No-connect pin with no connection to any internal circuitry; it may be tied to GND or VIN or left floating. |
| 2 | OUT | power_out | Output supplies power to the load and requires a minimum 3.3µF output capacitor to prevent oscillations. |
| 3 | OUT | power_out | Output supplies power to the load and requires a minimum 3.3µF output capacitor to prevent oscillations. |
| 4 | NC | unconnected | No-connect pin with no connection to any internal circuitry; it may be tied to GND or VIN or left floating. |
| 5 | SENSE/ADJ | input | For the fixed-output LT1763-5 this is the SENSE input to the error amplifier, which should be connected to OUT at the point of optimum regulation, with a 10µA bias current at the nominal output voltage. |
| 6 | BYP | passive | Bypass pin clamped internally to ±0.6V, where a maximum 0.01µF capacitor from the output reduces output noise to a typical 20µVRMS over 10Hz to 100kHz; leave it unconnected if not used. |
| 7 | GND | power_in | Ground pin that should be tied directly to exposed pad pin 13 and to the bottom of the output voltage setting divider. |
| 8 | SHDN | input | Shutdown input where the output is off when pulled low, driven by 5V logic or open-collector logic with a pull-up resistor, and it must be tied to VIN if unused; SHDN pin voltage is rated ±20V. |
| 9 | NC | unconnected | No-connect pin with no connection to any internal circuitry; it may be tied to GND or VIN or left floating. |
| 10 | IN | power_in | Input supplying power to the device, requiring a 1µF to 10µF bypass capacitor when more than six inches from the main input filter; IN pin voltage is rated ±20V. |
| 11 | IN | power_in | Input supplying power to the device, requiring a 1µF to 10µF bypass capacitor when more than six inches from the main input filter; IN pin voltage is rated ±20V. |
| 12 | NC | unconnected | No-connect pin with no connection to any internal circuitry; it may be tied to GND or VIN or left floating. |
| 13 | GND | power_in | Exposed pad is the electrical and thermal ground connection that must be soldered to the PCB ground and tied directly to pin 7. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-12-EP(3x4) |
| Category | Power Supply Chip |
| Pins | 13 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Minimum Operating Voltage (C, I grade) | 1.8 | 2.3 | V | C, I Grade: ILOAD = 500mA | 4 | ||
| Regulated Output Voltage LT1763-5 | 4.95 | 5 | 5.05 | V | VIN = 5.5V, ILOAD = 1mA | 4 | |
| Regulated Output Voltage LT1763-5 (full operating temperature range) | 4.875 | 5 | 5.125 | V | 6V < VIN < 20V, 1mA < ILOAD < 500mA | 4 | |
| Line Regulation LT1763-5 | 1 | 5 | mV | ∆VIN = 5.5V to 20V, ILOAD = 1mA | 4 | ||
| Load Regulation LT1763-5 | 12 | 25 | mV | VIN = 6V, ∆ILOAD = 1mA to 500mA | 4 | ||
| Load Regulation LT1763-5 (full operating temperature range) | 50 | mV | VIN = 6V, ∆ILOAD = 1mA to 500mA | 4 | |||
| Dropout Voltage | 0.13 | 0.19 | V | VIN = VOUT(NOMINAL), ILOAD = 10mA | 4 | ||
| Dropout Voltage (full operating temperature range) | 0.25 | V | VIN = VOUT(NOMINAL), ILOAD = 10mA | 4 | |||
| Dropout Voltage | 0.17 | 0.22 | V | VIN = VOUT(NOMINAL), ILOAD = 50mA | 4 | ||
| Dropout Voltage (full operating temperature range) | 0.32 | V | VIN = VOUT(NOMINAL), ILOAD = 50mA | 4 | |||
| Dropout Voltage | 0.2 | 0.24 | V | VIN = VOUT(NOMINAL), ILOAD = 100mA | 4 | ||
| Dropout Voltage (full operating temperature range) | 0.34 | V | VIN = VOUT(NOMINAL), ILOAD = 100mA | 4 | |||
| Dropout Voltage | 0.3 | 0.35 | V | VIN = VOUT(NOMINAL), ILOAD = 500mA | 4 | ||
| Dropout Voltage (full operating temperature range) | 0.45 | V | VIN = VOUT(NOMINAL), ILOAD = 500mA | 4 | |||
| GND Pin Current | 30 | 75 | µA | VIN = VOUT(NOMINAL), ILOAD = 0mA | 5 | ||
| GND Pin Current | 65 | 120 | µA | VIN = VOUT(NOMINAL), ILOAD = 1mA | 5 | ||
| GND Pin Current | 1.1 | 1.6 | mA | VIN = VOUT(NOMINAL), ILOAD = 50mA | 5 | ||
| GND Pin Current | 2 | 3 | mA | VIN = VOUT(NOMINAL), ILOAD = 100mA | 5 | ||
| GND Pin Current | 5 | 8 | mA | VIN = VOUT(NOMINAL), ILOAD = 250mA | 5 | ||
| GND Pin Current | 11 | 16 | mA | VIN = VOUT(NOMINAL), ILOAD = 500mA | 5 | ||
| Quiescent Current in Shutdown | 0.1 | 1 | µA | VIN = 6V, VSHDN = 0V | 5 | ||
| Ripple Rejection | 50 | 65 | dB | VIN, VOUT = 1.5V (Avg), VRIPPLE = 0.5VP-P, fRIPPLE = 120Hz, ILOAD = 500mA | 5 | ||
| Current Limit (C, I grade) | 520 | mA | C, I Grade: VIN = VOUT(NOMINAL) + 1V or 2.3V (Note 12), ∆VOUT = -0.1V | 5 | |||
| Input Reverse Leakage Current | 1 | mA | VIN = -20V, VOUT = 0V | 5 | |||
| Reverse Output Current LT1763-5 | 10 | 20 | µA | VOUT = 5V, VIN < 5V | 5 | ||
| IN Pin Voltage | -20 | 20 | V | 2 | |||
| OUT Pin Voltage | -20 | 20 | V | 2 | |||
| Input to Output Differential Voltage | -20 | 20 | V | 2 | |||
| SENSE Pin Voltage | -20 | 20 | V | 2 | |||
| BYP Pin Voltage | -0.6 | 0.6 | V | 2 | |||
| SHDN Pin Voltage | -20 | 20 | V | 2 | |||
| Storage Temperature Range (DFN package) | -65 | 150 | °C | DFN package | 2 | ||
| Operating Junction Temperature Range | -40 | 125 | °C | C grade | 2 | ||
| Maximum Junction Temperature (TJMAX) | 125 | °C | DE package | 2 | |||
| Junction-to-Ambient Thermal Resistance (θJA) | 40 | °C/W | DE package; board 2500mm², topside copper 2500mm², backside copper 2500mm² | 16 | |||
| Junction-to-Ambient Thermal Resistance (θJA) | 45 | °C/W | DE package; board 1000mm², topside copper 2500mm², backside copper 2500mm² | 16 | |||
| Junction-to-Ambient Thermal Resistance (θJA) | 50 | °C/W | DE package; board 225mm², topside copper 2500mm², backside copper 2500mm² | 16 | |||
| Junction-to-Ambient Thermal Resistance (θJA) | 60 | °C/W | DE package; board 100mm², topside copper 2500mm², backside copper 2500mm² | 16 | |||
| Junction-to-Case Thermal Resistance (θJC) | 5 | °C/W | DE package | 2 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | COPPER | Table 1. DE Package, 12-Lead DFN COPPER AREA | 16 |
CAD (KiCad official)
- Symbol:
LT1763CDE-5#TRPBF - Footprint:
Package_DFN_QFN:DFN-12-1EP_3x4mm_P0.5mm_EP1.7x3.3mm - 3D model: DFN-12-EP(3x4) (KiCad packages3D, STEP)
- 3D model files:
lt1763cde-5-trpbf-etched.step/lt1763cde-5-trpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt1763cde-5-trpbf.step/lt1763cde-5-trpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (22 pp, sha256
2bc1aa72821928b4, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).