3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownSN6507DGQRQ1
Texas Instruments · Power Management - Specialized · HVSSOP-10
SN6507DGQRQ1 from Texas Instruments, in a HVSSOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW1 | output | Open-drain output of the first power MOSFET (switch 1), typically connected to either outer terminal of the center-tap transformer, with external traces kept short because of large currents. |
| 2 | GND | power_in | Ground connection for the internal control circuits and power MOSFET; pin 2 and pin 9 must be shorted on the PCB for optimized emissions and efficiency. |
| 3 | VCC | power_in | Main supply pin for the power and analog circuits, specified at 3 V to 36 V in the recommended operating conditions, and it sees short high-current pulses during power-switch turn-on and turn-off. |
| 4 | EN/UVLO | input | Enable and undervoltage-lockout programming input; the device switches only when this pin is above the EN/UVLO threshold (1.5 V typical rising) and VCC is above its UVLO threshold, and it stops switching when floating or below the threshold. |
| 5 | DC | input | Duty-cycle control input where a resistor to GND sets the duty cycle; leaving it floating selects the 48% typical default, and duty-cycle control is disabled in SYNC mode. |
| 6 | SR | input | Slew-rate control input where a resistor to GND sets the slew rate of SW1 and SW2 (RSR 4.8 kΩ to 21 kΩ), floating selects the default slew rate, and a short to GND is treated as a fault that stops switching. |
| 7 | CLK | input | External clock input for SYNC mode or frequency-program pin, where a resistor to GND (4 kΩ to 111 kΩ) sets the switching frequency, a short to GND selects the 1 MHz default, and a floating pin stops switching. |
| 8 | SS/ILIM | input | Multifunction soft-start and current-limit pin, where a capacitor to GND (0.05 µF to 10 µF recommended) sets the soft-start time and a resistor to GND (18 kΩ to 261 kΩ) sets the programmable current limit, and both must be present. |
| 9 | GND | power_in | Ground connection for the internal control circuits and power MOSFET; pin 9 and pin 2 must be shorted on the PCB for optimized emissions and efficiency. |
| 10 | SW2 | output | Open-drain output of the second power MOSFET (switch 2), typically connected to either outer terminal of the center-tap transformer, with external traces kept short because of large currents. |
| 11 | PowerPAD | power_in | Exposed thermal pad that must be electrically connected to GND pins 2 and 9 on the printed circuit board for proper operation. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HVSSOP-10 |
| Category | Power Management (PMIC) |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | -0.5 | 60 | V | 4 | ||
| Voltage EN/UVLO | EN/UVLO | -0.5 | V | 4 | |||
| Voltage SS/ILIM, CLK, DC | SS/ILIM, CLK, DC | -0.5 | 6 | V | 4 | ||
| Output switch voltage SW1, SW2 | SW1, SW2 | 85 | V | 4 | |||
| Peak output switch current | I(D1)Pk, I(D2)Pk | 1.6 | A | 4 | |||
| Junction temperature | TJ | -55 | 150 | °C | 4 | ||
| Storage temperature range | Tstg | -65 | 150 | °C | 4 | ||
| VCC Input Voltage | VCC | 3 | 36 | V | 4 | ||
| Output switch current - Primary side | ISW1, ISW2 | 0.4 | A | 3 V < VCC < 6 V | 4 | ||
| Output switch current - Primary side | ISW1, ISW2 | 0.5 | A | 6 V < VCC < 36 V | 4 | ||
| Ambient temperature | TA | -55 | 125 | °C | 4 | ||
| Junction temperature | TJ | -55 | 150 | °C | 4 | ||
| Soft-start capacitor on SS/ILIM pin | CSS | 0.05 | 10 | µF | 4 | ||
| Current limiting resistor on SS/ILIM pin | RILIM | 18 | 261 | kΩ | 4 | ||
| Resistor on SR pin for Slew rate control | RSR | 4.8 | 21 | kΩ | 4 | ||
| Resistor on CLK pin for programmable frequency | RCLK | 4 | 111 | kΩ | 4 | ||
| VIN supply current (not incl. switch drive currents) | Icc | 3 | 4 | mA | 3 V < VCC < 36 V, VEN/UVLO=2.5 V, RL = 50 Ω | 5 | |
| VIN shutdown current | ISHUTDOWN | 0.8 | 2.5 | µA | VEN/UVLO=0 V, RL = 50 Ω | 5 | |
| Leakage current on SS/ILIM pin | ILKG(SS/ILIM) | 0.7 | µA | VEN/UVLO = 0 V, Voltage of SS/ILIM = 5 V | 5 | ||
| VCC positive-going UVLO threshold | VCCUVLO-RISING | 2.8 | 2.9 | V | VCC rising, EN/UVLO is shorted to VCC | 5 | |
| VCC negative-going UVLO threshold | VCCUVLO-FALLING | 2.5 | 2.67 | V | VCC falling, EN/UVLO is shorted to VCC | 5 | |
| VCC UVLO threshold hysteresis | VCCUVLO-HYS | 0.1 | 0.12 | V | EN/UVLO is shorted to VCC | 5 | |
| EN/UVLO positive-going UVLO threshold | ENUVLO-RISING | 1.4 | 1.5 | 1.6 | V | EN/UVLO rising | 5 |
| EN/UVLO negative-going UVLO threshold | ENUVLO-FALLING | 1.25 | 1.35 | 1.45 | V | EN/UVLO falling | 5 |
| EN/UVLO UVLO threshold hysteresis | ENUVLO-HYS | 0.14 | 0.15 | V | 5 | ||
| Average ON time mismatch between SW1 and SW2 | DMM | 0 | % | RL = 50 Ω to VCC, Pull-Up Resistor Test Circuit Configuration | 5 | ||
| Output switch ON resistance | R(ON) | 0.45 | 1 | Ω | VCC = 24 V, ISW1, ISW2 = 0.5 A | 5 | |
| D1, D2 average switching frequency (Default) | FSW | 780 | 1000 | 1296 | kHz | RL = 50 Ω, RCLK = 0 kΩ, Pull-Up Resistor Test Circuit Configuration | 5 |
| External clock frequency on CLK pin | F(SYNC) | 200 | 4000 | kHz | External clock applied on CLK pin for SYNC mode | 5 | |
| CLK pin logic high threshold | VCLK(High) | 1.6 | 1.8 | V | 5 | ||
| CLK pin logic low threshold | VCLK(Low) | 1 | 1.2 | V | 5 | ||
| SS ext capacitor range | CSS Range | 0.05 | 5 | µF | 5 | ||
| SW1 and SW2 current limit | ILIM | 1 | 1.3 | 1.59 | A | RLIM = 18.2 kΩ, 5 V < VCC < 36 V | 5 |
| SW1 and SW2 current limit | ILIM | 0.56 | 0.79 | 1.02 | A | RLIM = 30.1 kΩ, 5 V < VCC < 36 V | 5 |
| SW1 and SW2 current limit | ILIM | 0.06 | 0.1 | 0.14 | A | RLIM = 261 kΩ, 5 V < VCC < 36 V | 5 |
| Input OVLO rising threshold | VCCOVLO-RISING | 36.9 | 38.7 | 40.5 | V | VCC rising | 6 |
| Input OVLO falling threshold | VCCOVLO-FALLING | 36.5 | 38.2 | 40 | V | VCC falling | 6 |
| Input OVLO hysteresis | VCCOVLO-HYS | 0.47 | 0.57 | V | VCC hysteresis voltage | 6 | |
| TSD turn on temperature | TSD+ | 170 | 184 | 198 | °C | TJ rising | 6 |
| TSD turn off temperature | TSD- | 135 | 147 | 159 | °C | TJ falling | 6 |
| TSD hysteresis | TSD-HYST | 32 | 37 | 42 | °C | 6 | |
| Power-up time | tPWRUP | 300 | 400 | µs | CSS = 0 µF, from EN = High to full drive-current available at SW1 and SW2 | 7 | |
| Power-down time | tPWRDN | 30 | µs | CSS = 0 µF, from EN = Low to output MOSFETs off (no current on SW1 and SW2) | 7 | ||
| Junction-to-ambient thermal resistance | RθJA | 48.2 | °C/W | 4 | |||
| Junction-to-case (top) thermal resistance | RθJC(top) | 61.6 | °C/W | 4 | |||
| Junction-to-board thermal resistance | RθJB | 18.4 | °C/W | 4 | |||
| Junction-to-top characterization parameter | ψJT | 1.7 | °C/W | 4 | |||
| Junction-to-board characterization parameter | ψJB | 18.3 | °C/W | 4 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bottom) | 5.8 | °C/W | 4 | |||
| Switch slew rate on SW1 and SW2 | V(SLEW) | 298 | V/µs | RL = 50 Ω to VCC, VCC = 12 V; RSR = 9.6 kΩ (Default), Pull-Up Resistor Test Circuit Configuration | 5 | ||
| Switch slew rate on SW1 and SW2 | V(SLEW) | 369 | V/µs | RL = 50 Ω to VCC, VCC = 12 V; RSR = 9.6 kΩ (Default), Pull-Up Resistor Test Circuit Configuration | 5 | ||
| Switching duty cycle on SW1 and SW2 | Dsw1, Dsw2 | 48 | % | DC pin floating (Default), FSW = 300KHz, Timing Diagram | 6 | ||
| SS ext capacitor charging current | ISS | 275 | µA | 5 | |||
| EN glitch filter | TEN_glitch | 5 | µs | 7 | |||
| Break-before-make time | tBBM | 70 | ns | Measured at 0.5VCC with RL = 50 Ω, FSW = 1 MHz, RSR = 9.6 kΩ (or Default), Timing Diagram | 7 |
CAD (KiCad official)
- Symbol:
SN6507DGQRQ1 - Footprint:
Package_SO:HVSSOP-10-1EP_3x3mm_P0.5mm_EP1.83x1.89mm - 3D model: HVSSOP-10, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.0 mm tall, family nominal (no datasheet A read)). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
sn6507dgqrq1-etched.step/sn6507dgqrq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sn6507dgqrq1.step/sn6507dgqrq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (44 pp, sha256
750f94554cd548d8, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).