3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMLX90371GDC-BCC-300-RE
Melexis · Angle, Linear Position Sensors · SOIC-8
MLX90371GDC-BCC-300-RE from Melexis, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD | power_in | Supply input; the absolute maximum ratings in Table 6 apply, including reverse voltage protection down to -14 V. |
| 2 | Test Input | input | Test input, for test use only; the datasheet recommends connecting it to ground for optimal EMC behavior. |
| 3 | Test | passive | Test pin, for test use only; the datasheet recommends connecting it to ground for optimal EMC behavior. |
| 4 | Not Used | unconnected | Not used; the datasheet recommends connecting it to ground for optimal EMC behavior. |
| 5 | OUT | output | Sensor output, ratiometric analog or PWM; output current is limited to ±30 mA over -1.5 V < VOUT < 40 V per Table 6. |
| 6 | VSSD | power_in | Ground (digital) return for the device. |
| 7 | VDEC | passive | Decoupling pin for the on-chip regulator, requiring an external decoupling capacitor. |
| 8 | VSSA | power_in | Ground (analog) return for the device. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Melexis |
| Package | SOIC-8 |
| Category | Sensors |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VDD | 4.5 | 5 | 5.5 | V | Supply voltage range, general electrical specifications valid -40 to 160 Deg.C | 13 |
| Supply Current (Standard/Legacy mode) | IDD | 6 | 9 | 10 | mA | Standard/Legacy mode, no resistive load at OUT PIN | 13 |
| Start-up Level (rising) | 3.95 | 4.1 | 4.25 | V | 13 | ||
| Start-up Hysteresis | 100 | 200 | 300 | mV | 13 | ||
| PTC Entry Level (rising) | 6.2 | 6.5 | 6.8 | V | IC to be programmed at room temperature | 13 | |
| PTC Entry Level Hysteresis | 400 | 500 | 600 | mV | 13 | ||
| Output Short Circuit Current | Ishort | -25 | -10 | mA | VOUT = 0 V | 13 | |
| Output Short Circuit Current | Ishort | 10 | 25 | mA | VOUT = 5 V or 18 V | 13 | |
| Output Load | RL | 5 | 10 | kΩ | Analog mode | 13 | |
| Output Load | RL | 2 | 10 | kΩ | Digital (PWM) mode | 13 | |
| Analog Saturation Output Level (low) | VsatA_lo | 0.5 | 1 | %VDD | Pull-up load RL ≥ 10 kΩ to 5 V | 13 | |
| Analog Saturation Output Level (low) | VsatA_lo | 3.5 | 5 | %VDD | Pull-up load RL ≥ 5 kΩ to 18 V | 13 | |
| Analog Saturation Output Level (high) | VsatA_hi | 96 | 97 | %VDD | Pull-down load RL ≥ 5 kΩ | 13 | |
| Analog Saturation Output Level (high) | VsatA_hi | 97.5 | 98 | %VDD | Pull-down load RL ≥ 10 kΩ | 13 | |
| Digital (PWM) Output Level (low) | VsatD_lo | 0.5 | 1 | %VDD | Pull-up load RL ≥ 10 kΩ to 5 V | 13 | |
| Digital (PWM) Output Level (low) | VsatD_lo | 3.5 | 5 | %VDD | Pull-up load RL ≥ 5 kΩ to 18 V | 13 | |
| Digital (PWM) Output Level (low) | VsatD_lo | 2.5 | 4 | %VDD | Pull-up load RL ≥ 2 kΩ to 5 V | 13 | |
| Digital (PWM) Output Level (high) | VsatD_hi | 85 | 90 | %VDD | Pull-down load RL ≥ 2 kΩ | 13 | |
| Digital (PWM) Output Level (high) | VsatD_hi | 96 | 97 | %VDD | Pull-down load RL ≥ 5 kΩ | 13 | |
| Digital (PWM) Output Level (high) | VsatD_hi | 97.5 | 98 | %VDD | Pull-down load RL ≥ 10 kΩ | 13 | |
| Supply Voltage (absolute maximum) | VDD | 28 | V | <48h | 12 | ||
| Supply Voltage (absolute maximum) | VDD | 45 | V | <1min | 12 | ||
| Reverse Voltage Protection | VDDREV | -14 | V | At Room Temperature; <48h | 12 | ||
| Positive Output Voltage | VOUT | 18 | V | <48h | 12 | ||
| Output Current | IOUT | -30 | 30 | mA | -1.5V < VOUT < 40V | 12 | |
| Reverse Output Voltage | VOUTREV | -0.3 | V | <48h | 12 | ||
| Operating Temperature | TAMB | -40 | 160 | °C | Refer to the qualification profile | 12 | |
| Junction Temperature | TJUNC | 175 | °C | 12 | |||
| Storage Temperature | TST | -55 | 170 | °C | Refer to the qualification profile | 12 | |
| Magnetic Flux Density | -1 | 1 | T | 12 | |||
| Start-up Time (analog) | τSU | 5 | ms | Analog mode | 16 | ||
| Analog OUT Slew-rate | SR | 200 | V/ms | no load, valid for both rising and falling edge | 16 | ||
| Analog OUT Slew-rate | SR | 120 | V/ms | capacitor load CL = 100 nF, valid for both rising and falling edge | 16 | ||
| Analog OUT Slew-rate | SR | 35 | V/ms | capacitor load CL = 330 nF, valid for both rising and falling edge | 16 | ||
| PWM Frequency | FPWM | 150 | 2000 | Hz | Ck = 18MHz | 17 | |
| PWM Frequency tolerance | ΔFPWM | -5 | 5 | %FPWM | Including thermal drift and aging | 17 | |
| PWM Frequency Thermal Drift | ΔTFPWM | -3 | 3 | %FPWM | 17 | ||
| Digital (PWM) output rise time | 2 | 11 | μs | Push-Pull, CL = 4.7 nF, RL = 4.7kΩ PU | 17 | ||
| Digital (PWM) output fall time | 2 | 11 | μs | Push-Pull, CL = 4.7 nF, RL = 4.7kΩ PU | 17 | ||
| Start-up Time (PWM) | τSU | 5 | ms | PWM mode @1kHz | 17 | ||
| Start-up Time (PWM) | τSU | 15 | ms | PWM mode @150Hz | 17 |
CAD (KiCad official)
- Symbol:
MLX90371GDC-BCC-300-RE - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files:
mlx90371gdc-bcc-300-re-etched.step/mlx90371gdc-bcc-300-re-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mlx90371gdc-bcc-300-re.step/mlx90371gdc-bcc-300-re.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Melexis datasheet (68 pp, sha256
70a96fa19159f008, retrieved 2026-10-28, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).