Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

UCC38C54DR

Texas Instruments · IC · SOIC-8

UCC38C54DR from Texas Instruments, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 COMP output Error amplifier output for loop compensation, internally current limited so forcing COMP to GND commands zero duty cycle.
2 FB input Inverting input of the error amplifier, whose noninverting input is internally trimmed to 2.5 V ±1%.
3 CS input Primary-side current sense input to the PWM comparator, connected to the current sensing resistor, used to terminate OUT conduction.
4 RT/CT bidirectional Oscillator set point: timing resistor to VREF and timing capacitor to GND set the switching frequency, which is half of fOSC on the UCC38C54.
5 GND power_in Ground return for the output driver stage and the logic level controller section.
6 OUT output Totem-pole gate drive output sourcing and sinking up to 1 A peak, at half the oscillator frequency (duty cycle below 50%) and actively held low when VDD is below turn-on threshold.
7 VDD power_in Analog controller bias supply input with 30 V absolute maximum, requiring a 0.1 µF bypass capacitor directly to GND.
8 VREF power_out 5-V reference output (±1%) that charges the timing capacitor through the timing resistor, requiring at least 0.1 µF ceramic bypass to GND and no external voltage applied.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package SOIC-8
Category
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage VDD 30 V 5
Input current IVDD 30 mA 5
Output drive current (peak) -1 1 A 5
Output energy (capacitive load) EOUT 5 µJ 5
Analog input voltage -0.3 6.3 V COMP, CS, FB, RT/CT 5
Output driver voltage OUT -0.3 30 V OUT 5
Reference voltage VREF 7 V 5
Error amplifier output sink current 10 mA COMP 5
Total power dissipation, D package 72.3 °C/W TA = 25°C, D package 5
Lead temperature TLEAD 300 °C soldering, 10 s 5
Operating junction temperature TJ -40 150 °C 5
Storage temperature Tstg -65 150 °C 5
ESD HBM V(ESD) -2500 2500 V Human-body model, ANSI/ESDA/JEDEC JS-001 6
ESD CDM V(ESD) -1500 1500 V Charged-device model, JESD22-C101 6
Input voltage VVDD 28 V 6
Output driver voltage VOUT 28 V 6
Average output driver current IOUT 200 mA 6
Reference output current IOUT(VREF) -20 mA 6
Operating junction temperature TJ 0 85 °C UCC38C5x 6
Junction-to-ambient thermal resistance RθJA 128.9 °C/W D (SOIC) 8 pins 6
Junction-to-case (top) thermal resistance RθJC(top) 71.7 °C/W D (SOIC) 8 pins 6
Junction-to-board thermal resistance RθJB 72.3 °C/W D (SOIC) 8 pins 6
VREF voltage, initial accuracy VVREF 4.95 5 5.05 V TJ = 25°C, IOUT = 1 mA 7
Line regulation 0.2 20 mV 12 V ≤ VVDD ≤ 25 V 7
Load regulation 3 25 mV 1 mA to 20 mA 7
VREF temperature stability 0.2 0.4 mV/°C Specified by design 7
VREF total output variation 4.85 5.15 V Specified by design 7
VREF long term stability 5 25 mV 1000 hours, TJ = 125°C 7
VREF output short circuit (source current) IVREF 30 45 55 mA 7
Oscillator initial accuracy fOSC 50.5 53 55 kHz TJ = 25°C 7
Oscillator voltage stability 0.2 1 % 12 V ≤ VVDD ≤ 25 V 7
Oscillator temperature stability 1 2.5 % TJ(MIN) to TJ(MAX) 7
Oscillator amplitude 1.9 V RT/CT pin peak-to-peak voltage 7
Oscillator discharge current 7.7 8.4 9 mA TJ = 25°C, VRT/CT = 2 V 7
Oscillator discharge current 7.2 8.4 9.5 mA VRT/CT = 2 V 7
Feedback input voltage, initial accuracy VFB 2.475 2.5 2.525 V VCOMP = 2.5 V, TJ = 25°C 7
Feedback input voltage, total variation VFB 2.45 2.5 2.55 V VCOMP = 2.5 V 7
Input bias current (source current) IFB 0.1 2 µA VFB = 5 V 7
Open-loop voltage gain AVOL 65 90 dB 2 V ≤ VOUT ≤ 4 V 7
Unity gain bandwidth 1 1.5 MHz Specified by design 7
Error amplifier output sink current 2 14 mA VFB = 2.7 V, VCOMP = 1.1 V 7
Error amplifier output source current 0.5 1 mA VFB = 2.3 V, VCOMP = 5 V 7
Low-level COMP voltage VOL 0.1 1.1 V VFB = 2.7 V, RCOMP = 15 kΩ COMP to VREF 7
Current sense gain ACS 2.85 3 3.15 V/V 7
Current sense maximum input signal VCS 0.9 1 1.1 V VFB < 2.4 V 7
Current sense input bias current (source current) ICS 0.1 2 µA 7
CS to output delay tD 35 70 ns 7
RDS(on) pulldown VOUT(low) 5.5 15 Ω ISINK = 200 mA 7
RDS(on) pullup VOUT(high) 10 25 Ω ISOURCE = 200 mA 7
Rise time tRISE 25 50 ns TJ = 25°C, COUT = 1 nF 7
Fall time tFALL 20 40 ns TJ = 25°C, COUT = 1 nF 7
Start threshold VDDON 13.5 14.5 15.5 V UCCx8C52, UCCx8C54 8
Minimum operating voltage VDDOFF 8 9 10 V UCCx8C52, UCCx8C54 8
UVLO hysteresis VDDHyst 5.4 5.5 V VDDON - VDDOFF, UCCx8C52, UCCx8C54 8
Maximum duty cycle DMAX 47 48 % UCCx8C54, VFB < 2.4 V 8
Start-up current ISTART-UP 50 75 µA VVDD = VDDON, 0.5 V 8
Operating supply current IVDD 1.3 2 mA VFB = VCS = 0 V 8
Minimum duty cycle DMIN 0 % VFB > 2.6 V 8

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts tin The inductor rising slope (Sn) at the CS pin is calculated with Equation 34. Sn = 34

CAD (KiCad official)

  • Symbol: UCC38C54DR
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOIC-8 (KiCad packages3D, STEP)
  • 3D model files: ucc38c54dr-etched.step / ucc38c54dr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ucc38c54dr.step / ucc38c54dr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (58 pp, sha256 d9b2cab289f0aa82, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF