component
TLD5190QUXUMA1
Public Made by Adomby adom
Infineon Technologies LED Drivers, TQFP-48(7x7). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownTLD5190QUXUMA1
Infineon Technologies · LED Drivers · TQFP-48(7x7)
TLD5190QUXUMA1 from Infineon Technologies, in a TQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | n.c. | unconnected | Not connected; tie to AGND on the layout. |
| 2 | HSGD1 | output | High-side gate driver output 1 drives the top n-channel MOSFET with a voltage equal to VIVCC_EXT superimposed on SWN1; connect to the gate of the external switching MOSFET. |
| 3 | BST1 | bidirectional | Bootstrap capacitor pin for internal biasing and HSGD1 drive; bypass to SWN1 with a capacitor close to the pin and do not leave open. |
| 4 | SWN1 | bidirectional | Switch node 1 swings from a diode voltage drop below ground up to VIN. |
| 5 | PGND1 | power_in | Power ground for the power potential; connect externally close to the chip. |
| 6 | LSGD1 | output | Low-side gate driver output 1 drives the low-side n-channel MOSFET between GND and VIVCC_EXT; connect to the gate of the external switching MOSFET. |
| 7 | LSGD2 | output | Low-side gate driver output 2 drives the low-side n-channel MOSFET between GND and VIVCC_EXT; connect to the gate of the external switching MOSFET. |
| 8 | PGND2 | power_in | Power ground for the power potential; connect externally close to the chip. |
| 9 | SWN2 | bidirectional | Switch node 2 swings from ground up to a diode voltage drop above VOUT. |
| 10 | BST2 | bidirectional | Bootstrap capacitor pin for internal biasing and HSGD2 drive; bypass to SWN2 with a capacitor close to the pin and do not leave open. |
| 11 | HSGD2 | output | High-side gate driver output 2 drives the top n-channel MOSFET with a voltage equal to VIVCC_EXT superimposed on SWN2; connect to the gate of the external switching MOSFET. |
| 12 | n.c. | unconnected | Not connected; tie to AGND on the layout. |
| 13 | FBH | input | Output current feedback positive, non-inverting input (+). |
| 14 | FBL | input | Output current feedback negative, inverting input (-). |
| 15 | n.c. | unconnected | Not connected; tie to AGND on the layout. |
| 16 | IOUTMON | output | Output current monitor producing 200 mV + 8 times VFBH-FBL, equal to 1.4 V at VFBH-FBL = 150 mV. |
| 17 | SWCS | input | Inductor current sense input, non-inverting input (+); route as differential net with SGND on the layout. |
| 18 | SGND | power_in | Inductor current sense ground, inverting input (-); route as differential net with SWCS on the layout. |
| 19 | COMP | output | Compensation network pin; connect an R and C network to the pin for stability and phase margin adjustment. |
| 20 | VFB | input | Voltage loop feedback pin intended to set output protection functions. |
| 21 | VREF | power_in | Voltage reference output supplying an accurate 2 V for standalone analog dimming and LED temperature compensation; bypass with 100 nF close to the pin and do not leave open. |
| 22 | SET | input | Analog current sense adjustment pin; a voltage VSET between 0.2 V and 1.5 V adjusts ILED or VOUT in a linear relation. |
| 23 | TEST1 | passive | Test pin used for Infineon end-of-line test; connect to GND in the application. |
| 24 | PWMI | input | Control input for PWM dimming; digital input 5 V or 3.3 V with integrated pull-down. |
| 25 | TEST2 | passive | Test pin used for Infineon end-of-line test; connect to GND in the application. |
| 26 | VSS | power_in | Digital GPIO ground reference for the GPIO pins. |
| 27 | CLKOUT | output | Clock output carrying the switching oscillator signal to supply SYNC inputs of other DC/DC devices; disabled during overtemperature. |
| 28 | TEST3 | passive | Test pin used for Infineon end-of-line test; connect to GND in the application. |
| 29 | TEST4 | passive | Test pin used for Infineon end-of-line test; connect to GND in the application. |
| 30 | TEST5 | passive | Test pin used for Infineon end-of-line test; connect to GND in the application. |
| 31 | TEST6 | passive | Test pin used for Infineon end-of-line test; connect to GND in the application. |
| 32 | EF2 | output | Open-drain error flag 2, pulled LOW when an open load, overvoltage or overtemperature occurs. |
| 33 | EF1 | output | Open-drain error flag 1, pulled LOW when an output short to GND or overtemperature occurs. |
| 34 | SYNC | input | Synchronization input with integrated pull-down; apply an external clock signal for synchronization. |
| 35 | FREQ | input | Frequency select input; connect an external resistor to GND to set the switching frequency. |
| 36 | INOVLO | input | Input overvoltage protection pin defining an upper VIN threshold and switching the device off on VIN overvoltage; must not be left open. |
| 37 | SPREAD_SPECTRUM | input | Spread spectrum enable pin with integrated pull-down; enables or disables the spread spectrum function for EMC performance. |
| 38 | SOFT_START | output | Soft-start configuration pin; connect a capacitor CSOFT_START to GND to fix the soft start ramp time. |
| 39 | IINMON | output | Input current monitor output producing 20 times VIIN1-IIN2, equal to 1 V at VIIN1-IIN2 = 50 mV. |
| 40 | AGND | power_in | Analog ground reference for the device. |
| 41 | EN/INUVLO | input | Enable and input undervoltage lockout pin with integrated pull-down for low current consumption mode and external UVLO threshold; must not be left open. |
| 42 | IIN1 | input | Input current monitor positive, non-inverting input (+); connect to VIN if the input current monitor is not needed. |
| 43 | IIN2 | input | Input current monitor negative, inverting input (-); connect to VIN if the input current monitor is not needed. |
| 44 | VIN | power_in | Power supply voltage supplying internal biasing of the device. |
| 45 | n.c. | unconnected | Not connected; tie to AGND on the layout. |
| 46 | IVCC | power_out | Internal LDO output used for internal biasing and gate driver supply; bypass with a capacitor close to the pin and do not leave open. |
| 47 | IVCC_EXT | input | External LDO input to alternatively supply the internal gate drivers; must not be left open and connects to IVCC to use the internal LDO. |
| 48 | n.c. | unconnected | Not connected; tie to AGND on the layout. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Infineon Technologies |
| Package | TQFP-48(7x7) |
| Category | Display Modules / LED Drivers / Display Drivers |
| Pins | 48 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage Startup | VVIN(ON) | 4.7 | V | VIN increasing; VEN/INUVLO = HIGH; IVCC = IVCC_EXT = 10 mA; | 15 | ||
| Input Undervoltage switch OFF | VVIN(OFF) | 4.5 | V | VIN decreasing; VEN/INUVLO = HIGH; IVCC = IVCC_EXT = 10 mA; | 15 | ||
| Device operating current | IVIN(ACTIVE) | 4.4 | 6 | mA | ACTIVE mode; CLKOUT freq. 300 KHz; VPWMI = 0 V; | 15 | |
| VIN Sleep mode supply current | IVIN(SLEEP) | 1.5 | µA | VEN/INUVLO = 0 V; VIN = 13.5 V; VIVCC = VIVCC_EXT= 0 V; | 15 | ||
| Input Undervoltage falling Threshold | VEN/INUVLOth | 1.6 | 1.75 | 1.9 | V | 15 | |
| EN/INUVLO input Current LOW | IEN/INUVLO(LOW) | 0.45 | 0.89 | 1.34 | µA | VEN/INUVLO = 0.8 V; | 15 |
| EN/INUVLO input Current HIGH | IEN/INUVLO(HIGH) | 1.1 | 2.2 | 3.3 | µA | VEN/INUVLO = 2 V; | 15 |
| SLEEP mode to ACTIVE time | tACTIVE | 0.7 | ms | VIVCC = VIVCC_EXT; CIVCC = 10 µF; VIN = 13.5 V; | 15 | ||
| V(FBH-FBL) threshold | V(FBH-FBL) | 145.5 | 150 | 154.5 | mV | VSET = 2 V; | 25 |
| V(FBH-FBL) threshold @ analog dimming 10% | V(FBH-FBL)_10 | 10 | 15 | 20 | mV | VSET = 0.32 V; | 25 |
| FBH Bias current @ highside sensing setup | IFBH_HSS | 65 | 110 | 155 | µA | VFBL = 7 V; VFBH - FBL = 150 mV; | 25 |
| FBL Bias current @ highside sensing setup | IFBL_HSS | 17 | 30 | 43 | µA | VFBL = 7 V; VFBH - FBL = 150 mV; | 25 |
| FBH Bias current @ lowside sensing setup | IFBH_LSS | -7.5 | -4 | -2.5 | µA | VFBL = 0 V; VFBH - FBL = 150 mV; | 25 |
| FBL Bias current @ lowside sensing setup | IFBL_LSS | -45 | -30 | -20 | µA | VFBL = 0 V; VFBH - FBL = 150 mV; | 25 |
| Output Monitor Voltage | VIOUTMON | 1.33 | 1.4 | 1.47 | V | VFBH - FBL = 150 mV; | 25 |
| Maximum BOOST Duty Cycle | DBOOST_MAX | 89 | 91 | 93 | % | fsw = 300 kHZ; | 25 |
| Input Current Sense threshold | VIIN1-IIN2 | 46 | 50 | 54 | mV | 25 | |
| Input current Monitor Voltage | VIINMON | 0.95 | 1 | 1.05 | V | VIIN1 - IIN2 = 50 mV; VIIN1 = VVIN(ON) to 55 V; | 25 |
| Switch Peak Over Current Threshold - BOOST | VSWCS_boost | 40 | 50 | 60 | mV | 25 | |
| Switch Peak Over Current Threshold - BUCK | VSWCS_buck | -60 | -50 | -40 | mV | 25 | |
| Soft Start pull up current | ISoft_Start_PU | 22 | 26 | 32 | µA | VSoft_Start = 1 V; | 25 |
| Soft Start pull down current | ISoft_Start_PD | 2.2 | 2.6 | 3.2 | µA | VSoft_Start = 1 V; | 25 |
| Soft Start Latch-OFF Threshold | VSoft_Start_LOFF | 1.65 | 1.75 | 1.85 | V | 26 | |
| Soft Start Reset Threshold | VSoft_Start_RESET | 0.1 | 0.2 | 0.3 | V | 26 | |
| Soft Start Voltage during regulation | VSoft_Start_reg | 1.9 | 2 | 2.1 | V | No Faults | 26 |
| Switching Frequency | fSW | 285 | 300 | 315 | kHz | Tj = 25°C; RFREQ= 37.4 kΩ; | 26 |
| SYNC Frequency | fSYNC | 200 | 700 | kHz | 26 | ||
| SYNC Turn On Threshold | VSYNC,ON | 2 | V | 26 | |||
| SYNC Turn Off Threshold | VSYNC,OFF | 0.8 | V | 26 | |||
| SYNC High Input Current | ISYNC,H | 15 | 30 | 45 | µA | VSYNC = 2.0 V; | 26 |
| SYNC Low Input Current | ISYNC,L | 6 | 12 | 18 | µA | VSYNC = 0.8 V; | 26 |
| Gate Driver undervoltage threshold | VBST1,2-VSWN1,2_UVth | 3.4 | 4 | V | VBST1,2 - VSWN1,2 decreasing; | 26 | |
| HSGD1,2 NMOS driver on-state resistance (Gate Pull Up) | RDS(ON_PU)HS | 1.4 | 2.3 | 3.7 | Ω | VBST1,2 - VSWN1,2 = 5 V; I source = 100 mA; | 26 |
| HSGD1,2 NMOS driver on-state resistance (Gate Pull Down) | RDS(ON_PD)HS | 0.6 | 1.2 | 2.2 | Ω | VBST1,2 - VSWN1,2 = 5 V; I sink = 100 mA; | 26 |
| LSGD1,2 NMOS driver on-state resistance (Gate Pull Up) | RDS(ON_PU)LS | 1.4 | 2.3 | 3.7 | Ω | VIVCC_EXT = 5 V; Isource = 100 mA; | 26 |
| LSGD1,2 NMOS driver on-state resistance (Gate Pull Down) | RDS(ON_PD)LS | 0.4 | 1.2 | 1.8 | Ω | VIVCC_EXT = 5 V; Isink = 100 mA; | 26 |
| HSGD1,2 Gate Driver peak sourcing current | IHSGD1,2_SRC | 380 | mA | VHSGD1,2 - VSWN1,2 = 1 V to 4 V; VBST1,2 - VSWN1,2 = 5 V | 26 | ||
| HSGD1,2 Gate Driver peak sinking current | IHSGD1,2_SNK | 410 | mA | VHSGD1,2 - VSWN1,2 = 4 V to 1 V; VBST1,2 - VSWN1,2 = 5 V | 26 | ||
| PWMI Turn On Threshold | VPWMI,ON | 2 | V | 30 | |||
| PWMI Turn Off Threshold | VPWMI,OFF | 0.8 | V | 30 | |||
| PWMI High Input Current | IPWMI,H | 15 | 30 | 45 | µA | VPWMI = 2.0 V; | 30 |
| PWMI Low Input Current | IPWMI,L | 6 | 12 | 18 | µA | VPWMI = 0.8 V; | 30 |
| Source current on SET Pin | ISET_source | 1 | µA | VSET = 0.2 V to 1.4 V; | 33 | ||
| IVCC Output Voltage | VIVCC | 4.8 | 5 | 5.2 | V | VIN= 13.5 V; 0.1 mA ≤ IIVCC ≤ 50 mA; | 35 |
| Output Current Limitation | ILIM | 70 | 90 | 110 | mA | VIVCC = 4 V; | 35 |
| Drop out Voltage (VIN - VIVCC) | VDR | 200 | 350 | mV | VIN = 5 V; IIVCC = 10 mA; | 35 | |
| IVCC Buffer Capacitor | CIVCC | 10 | µF | 35 | |||
| IVCC_EXT Undervoltage Reset switch OFF Threshold | VIVCC_EXT_RTH,d | 3.7 | 3.9 | 4.1 | V | VIVCC_EXT decreasing; | 35 |
| IVCC Undervoltage Reset switch OFF Threshold | VIVCC_RTH,d | 3.7 | 3.9 | 4.1 | V | VIVCC decreasing; | 35 |
| IVCC and IVCC_EXT Undervoltage Hysteresis | VIVCCX_HYST | 0.3 | 0.33 | 0.36 | V | VIVCC increasing; VIVCC_EXT increasing; | 35 |
| VREF voltage | VREF | 1.94 | 2 | 2.06 | V | 0 ≤ IVREF ≤ 200 µA; | 35 |
| Short to GND threshold | VVFB_S2G | 0.53 | 0.563 | 0.59 | V | VVFB decreasing; | 42 |
| Over Temperature Shutdown | Tj,SD | 160 | 175 | 190 | °C | 42 | |
| VFB Over Voltage Feedback Threshold | VVFB_OVTH | 1.42 | 1.46 | 1.5 | V | 42 | |
| Output Over Voltage Feedback Hysteresis | VVFB_OVTH,HYS | 25 | 40 | 58 | mV | Output Voltage decreasing; | 42 |
| Open Load rising Threshold | VVFB_OL,rise | 1.29 | 1.34 | 1.39 | V | VFBH-FBL = 0 V; | 42 |
| Open Load reference Voltage VFBH-FBL | VFBH_FBL_OL | 15 | 22.5 | mV | VFB = 1.4 V; | 42 | |
| Open Load falling Threshold | VVFB_OL,fall | 1.23 | 1.28 | 1.33 | V | VFBH-FBL = 0 V; | 42 |
| Input Overvoltage rising Threshold | VINOVLOth | 1.9 | 2 | 2.1 | V | 42 | |
| Input Overvoltage Threshold Hysteresis | VINOVLO(hyst) | 18 | 40 | 62 | mV | 42 |
CAD (KiCad official)
- Symbol:
TLD5190QUXUMA1 - Footprint:
Package_QFP:TQFP-48_7x7mm_P0.5mm - 3D model: TQFP-48(7x7) (KiCad packages3D, STEP)
- 3D model files:
tld5190quxuma1-etched.step/tld5190quxuma1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tld5190quxuma1.step/tld5190quxuma1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Infineon Technologies datasheet (59 pp, sha256
a11dab213dca0565, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).