Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

SST26VF040AT-80E

Microchip Tech · NOR FLASH · SOIC-8

SST26VF040AT-80E from Microchip Tech, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 CE# input Chip Enable: the device is enabled by a high-to-low transition on CE#, and CE# must remain low for the duration of any command sequence or of the command/data input sequence for write operations.
2 SO/SIO1 bidirectional Serial Data Output in SPI mode (default after Power-on Reset or hardware Reset), shifted out on the falling edge of SCK; functions as SIO1 in SQI mode, where it is latched on the rising edge of SCK and is high-impedance during Reset.
3 WP#/SIO2 bidirectional Write-Protect used with the WPEN and IOC bits in the Configuration register to prohibit writes to the Block Protection register, and it only works in SPI single-bit and dual-bit Read mode; functions as SIO2 in quad mode.
4 Vss power_in Ground reference for the device.
5 SI/SIO0 bidirectional Serial Data Input in SPI mode (default after Power-on Reset or hardware Reset), latched on the rising edge of SCK; functions as SIO0 in SQI mode, configured by the Enable Quad I/O (EQIO) command.
6 SCK input Serial Clock: commands, addresses, or input data are latched on the rising edge, and output data is shifted out on the falling edge.
7 RESET#/HOLD#/SIO3 bidirectional Multiplexed pin: RESET# (requires Configuration register bit 6 set to 1) must be driven low for a minimum of TRST to reset the device; HOLD# (factory default, pauses serial communication in SPI single-bit and dual-bit Read modes) must be tied high when not in use; functions as SIO3 in quad mode.
8 VDD power_in Power supply voltage; the device operates from a single power supply of 2.3V-3.6V for write operations, and 2.7V-3.6V or 2.3V-3.6V for read operations.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package SOIC-8
Category Memory
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Read Current IDDR1 8 15 mA VDD=VDD Max, CE#=0.1VDD/0.9VDD @40 MHz, SO open 42
Program and Erase Current IDDW 25 mA VDD Max 42
Standby Current ISB1 15 30 µA CE#=VDD, VIN=VDD or VSS 42
Standby Current at 125°C ISB2 50 µA CE#=VDD, VIN=VDD or VSS at 125°C 42
Deep Power-Down Current IDPD1 8 20 µA CE#=VDD, VIN=VDD or VSS 42
Deep Power-Down Current at 125°C IDPD2 30 µA CE#=VDD, VIN=VDD or VSS at 125°C 42
Input Leakage Current ILI 2 µA VIN=GND to VDD, VDD=VDD Max 42
Output Leakage Current ILO 2 µA VOUT=GND to VDD, VDD=VDD Max 42
Input Low Voltage VIL 0.8 V VDD=VDD Min 42
Input High Voltage VIH 0.7 VDD VDD=VDD Max; printed as 0.7 VDD 42
Output Low Voltage VOL 0.2 V IOL=100 µA, VDD=VDD Min 42
Output High Voltage VOH -0.2 V Printed as VDD-0.2 V (offset from VDD); IOH=-100 µA, VDD=VDD Min 42
Output Pin Capacitance COUT 8 pF VOUT=0V, TA=25°C, f=1 MHz 42
Input Capacitance CIN 6 pF VIN=0V, TA=25°C, f=1 MHz 42
Endurance NEND 100000 cycles JEDEC A117 and AEC-Q100-005 42
Data Retention TDR 100 years JEDEC A103 and AEC-Q100-005 42
Latch Up ILTH 100 mA Printed as 100 + IDD; JEDEC 78 and AEC-Q100-004 42
Sector Erase TSE 25 ms VDD=2.3V-3.6V 42
Block Erase TBE 25 ms VDD=2.3V-3.6V 42
Chip Erase TSCE 50 ms VDD=2.3V-3.6V 42
Page Program TPP 1.5 ms VDD=2.3V-3.6V 42
Program Security ID TPSID 1.5 ms VDD=2.3V-3.6V 42
Write Suspend Latency TWS 25 µs VDD=2.3V-3.6V 42
Configuration Register Write Latency TCONFIG 25 ms VDD=2.3V-3.6V 43
Serial Clock Frequency FCLK 80 MHz 80 MHz column, VDD=2.3V-3.6V 44
Serial Clock Period TCLK 12.5 ns 80 MHz column, VDD=2.3V-3.6V 44
Serial Clock High Time TSCKH 5.5 ns 80 MHz column, VDD=2.3V-3.6V 44
Serial Clock Low Time TSCKL 5.5 ns 80 MHz column, VDD=2.3V-3.6V 44
Serial Clock Rise Time (slew rate) TSCKR 0.1 V/ns 80 MHz column; max rise/fall may be limited by TSCKH/TSCKL 44
Serial Clock Fall Time (slew rate) TSCKF 0.1 V/ns 80 MHz column; max rise/fall may be limited by TSCKH/TSCKL 44
CE# Active Setup Time TCES 5 ns 80 MHz column, relative to SCK 44
CE# Active Hold Time TCEH 5 ns 80 MHz column, relative to SCK 44
CE# Not Active Setup Time TCHS 5 ns 80 MHz column, relative to SCK 44
CE# Not Active Hold Time TCHH 5 ns 80 MHz column, relative to SCK 44
CE# High Time TCPH 12.5 ns 80 MHz column 44
CE# High-to-High Z Output TCHZ 12.5 ns 80 MHz column 44
HOLD# Low Setup Time THLS 5 ns 80 MHz column 44
HOLD# High Setup Time THHS 5 ns 80 MHz column 44
HOLD# Low Hold Time THLH 5 ns 80 MHz column 44
HOLD# High Hold Time THHH 5 ns 80 MHz column 44
HOLD# Low-to-High Z Output THZ 8 ns 80 MHz column 44
HOLD# High-to-Low Z Output TLZ 8 ns 80 MHz column 44
Data In Setup Time TDS 3 ns 80 MHz column 44
Data In Hold Time TDH 4 ns 80 MHz column 44
Output Hold from SCK Change TOH 0 ns 80 MHz column 44
Output Valid from SCK TV 8 ns 80 MHz column; printed 8/5 ns for 30 pF/10 pF load 44
VDD Minimum to Read Operation TPU-READ 100 µs Power-up 40
VDD Minimum to Write Operation TPU-WRITE 100 µs Power-up 40
Power-Down Duration TPD 100 ms Power-down 40
VDD Off VOFF 0.3 V 0 V recommended 40
Supply Voltage VDD VDD 2.3 3.6 V Extended operating range 40
Ambient Temperature (Extended) TA -40 125 °C Extended range; max operating frequency 80 MHz 40
Temperature Under Bias TBIAS -55 125 °C Under bias 40
Storage Temperature TSTG -65 150 °C 40
DC Voltage on Any Pin to Ground VPIN -0.5 0.5 V Printed as -0.5V to VDD+0.5V (max is offset from VDD) 40
Transient Voltage on Any Pin to Ground VPIN-T -2 2 V <20 ns; printed as -2.0V to VDD+2.0V (max is offset from VDD) 40
Package Power Dissipation Capability PD 1 W TA=25°C 40

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts tin 8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm (.150 In.) Body [SOIC] A A2 49

CAD (KiCad official)

  • Symbol: SST26VF040AT-80E
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOIC-8 (KiCad packages3D, STEP)
  • 3D model files: sst26vf040at-80e-etched.step / sst26vf040at-80e-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); sst26vf040at-80e.step / sst26vf040at-80e.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (73 pp, sha256 20b7245e058de3f5, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF