Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LIS2DW12TR

STMicroelectronics · Accelerometers · LGA-12

LIS2DW12TR from STMicroelectronics, in a LGA-12. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SCL/SPC input I²C serial clock (SCL) in I²C mode and SPI serial port clock (SPC) in SPI mode.
2 CS input Selects the interface: 1 enables I²C with SPI idle, 0 selects SPI with I²C disabled, and the pin is internally pulled up (20.4 kΩ typ. at 3.6 V Vdd_IO).
3 SDO/SA0 bidirectional SPI serial data output (SDO) or I²C least significant bit of the device address (SA0), internally pulled up.
4 SDA/SDI/SDO bidirectional I²C serial data (SDA), SPI serial data input (SDI), or 3-wire interface serial data output (SDO).
5 NC unconnected Internally not connected; can be tied to VDD, VDDIO, or GND.
6 GND power_in 0 V supply.
7 RES passive Reserved pin; connect to GND.
8 GND power_in 0 V supply.
9 VDD power_in Core power supply, operating range 1.62 V to 3.6 V; decoupling capacitors (100 nF ceramic, 10 µF aluminum) should be placed as near as possible to this pin.
10 VDD_IO power_in Power supply for the I/O pins, which can remain powered while VDD is removed without blocking the communication bus.
11 INT2 bidirectional Interrupt pin 2, also the clock input when single data conversion on demand is selected.
12 INT1 output Interrupt pin 1, programmable through the I²C/SPI interface.

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package LGA-12
Category Sensors
Pins 12

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage Vdd 1.62 1.8 3.6 V 7
I/O pins supply voltage Vdd_IO 1.62 V 7
Supply current in high-performance mode IddHR 90 µA @ ODR range 12.5 Hz - 1600 Hz, 14-bit 7
Supply current in low-power mode IddLP 5 µA ODR 100 Hz 7
Supply current in low-power mode IddLP 3 µA ODR 50 Hz 7
Supply current in low-power mode IddLP 1 µA ODR 12.5 Hz 7
Supply current in low-power mode IddLP 0.38 µA ODR 1.6 Hz 7
Supply current in power-down Idd_PD 50 nA 7
Digital low-level output voltage VOL 0.2 V IOL = 4 mA 7
Operating temperature range Top -40 85 °C 8
Temperature offset Toff -15 15 °C 8
Zero-g level offset accuracy Toff -20 20 mg 6
Zero-g offset change vs. temperature TCO -0.2 0.2 mg/°C 6
Self-test positive difference ST 70 1500 mg 6
Supply voltage Vdd -0.3 4.8 V 12
I/O pins supply voltage Vdd_IO -0.3 4.8 V 12
Input voltage on any control pin Vin -0.3 V CS, SCL/SPC, SDA/SDI/SDO, SDO/SA0 12
Acceleration (powered) APOW 3000 g any axis, powered, Vdd = 1.8 V, 0.5 ms 12
Acceleration (powered) APOW 10000 g any axis, powered, Vdd = 1.8 V, 0.2 ms 12
Acceleration (unpowered) AUNP 3000 g any axis, unpowered, 0.5 ms 12
Acceleration (unpowered) AUNP 10000 g any axis, unpowered, 0.2 ms 12
Operating temperature range TOP -40 85 °C 12
Storage temperature range TSTG -40 125 °C 12
Electrostatic discharge protection ESD 2 kV HBM 12
SPI clock cycle tc(SPC) 100 ns 9
SPI clock frequency fc(SPC) 10 MHz 9
CS setup time tsu(CS) 6 ns 9
CS hold time th(CS) 8 ns 9
SDI input setup time tsu(SI) 12 ns 9
SDI input hold time th(SI) 15 ns 9
SDO valid output time tv(SO) 50 ns 9
SDO output hold time th(SO) 9 ns 9
SDO output disable time tdis(SO) 50 ns 9
Temperature sensor output change vs. temperature TSDr 1 LSB/°C 8-bit resolution 8
Temperature sensor output change vs. temperature TSDr 16 LSB/°C 12-bit resolution 8
Sensitivity change vs. temperature TCS 0.01 %/°C 6

CAD (KiCad official)

  • Symbol: LIS2DW12TR
  • Footprint: Package_LGA:LGA-12_2x2mm_P0.5mm
  • 3D model: LGA-12, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.7 mm tall, datasheet A, max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: lis2dw12tr-etched.step / lis2dw12tr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lis2dw12tr.step / lis2dw12tr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (65 pp, sha256 5208623aa91c63a3, retrieved 2026-11-12, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF