3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLT8609IMSE#PBF
Analog Devices · DC-DC Converters · MSOP-10-EP
LT8609IMSE#PBF from Analog Devices, in a MSOP-10-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BST | power_out | Provides a drive voltage higher than the input voltage to the topside power switch, so a 0.1µF boost capacitor must be placed as close as possible to the IC and no resistor may be placed in series with this pin. |
| 2 | SW | power_out | Output of the internal power switches that connects to the inductor and boost capacitor, and this node should be kept small on the PCB for good performance. |
| 3 | INTVCC | power_out | Internal 3.5V regulator bypass pin with a maximum output current of 20mA that varies between 2.8V and 3.5V, to be decoupled to power ground with at least a 1µF low ESR ceramic capacitor and not loaded with external circuitry. |
| 4 | RT | passive | A resistor tied between RT and ground sets the switching frequency. |
| 5 | SYNC | input | External clock synchronization input that is grounded for low-ripple Burst Mode operation at low output loads, tied to a clock source to synchronize, left floating for pulse-skipping mode without spread spectrum, or tied to INTVCC or a voltage between 3.2V and 5.0V for pulse-skipping mode with spread spectrum modulation. |
| 6 | FB | input | Feedback pin of the adjustable output parts that the device regulates to 0.782V, with the feedback resistor divider tap connected to this pin. |
| 7 | TR/SS | input | Output tracking and soft-start pin where a voltage below 0.782V forces FB to follow the TR/SS voltage and an internal 2µA pull-up from INTVCC sets the output ramp rate, and it is pulled to ground through a 300Ω MOSFET during shutdown and fault conditions. |
| 8 | PG | output | Open-drain power good output that stays low until FB is within ±8.5% of the final regulation voltage with no fault conditions, and is valid when VIN is above 3.2V regardless of the EN/UV state. |
| 9 | VIN | power_in | Supplies current to the internal circuitry and the internal topside power switch, has an absolute maximum rating of 42V, and must be locally bypassed with the input capacitor positive terminal placed as close as possible to the VIN pins. |
| 10 | EN/UV | input | Shutdown pin that disables the part when low and enables it when high, with a hysteretic threshold of 1.05V rising and 1.00V falling, and it should be tied to VIN if the shutdown feature is not used. |
| 11 | GND | power_in | Exposed pad that must be connected to the negative terminal of the input capacitor and soldered to the PCB to lower the thermal resistance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-10-EP |
| Category | Power Management |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Minimum Input Voltage | 2.7 | 3 | 3.2 | V | full temp range (l) | 4 | |
| VIN Quiescent Current (LT8609/LT8609A), VEN/UV = 0V, VSYNC = 0V | 1 | 4 | µA | VEN/UV = 0V, VSYNC = 0V | 4 | ||
| VIN Quiescent Current (LT8609/LT8609A), VEN/UV = 2V, Not Switching, VSYNC = 0V | 1.7 | 12 | µA | VEN/UV = 2V, Not Switching, VSYNC = 0V, full temp range (l) | 4 | ||
| VIN Current in Regulation (LT8609/LT8609A), 100µA load | 46 | 90 | µA | VIN = 6V, VOUT = 2.7V, Output Load = 100µA, full temp range (l) | 4 | ||
| VIN Current in Regulation (LT8609/LT8609A), 1mA load | 480 | 700 | µA | VIN = 6V, VOUT = 2.7V, Output Load = 1mA, full temp range (l) | 4 | ||
| Feedback Reference Voltage (LT8609/LT8609A E/I/H-Grade), 25°C row | 0.778 | 0.782 | 0.786 | V | VIN = 6V, ILOAD = 100mA | 4 | |
| Feedback Reference Voltage (LT8609/LT8609A E/I/H-Grade), full temp range | 0.77 | 0.782 | 0.794 | V | VIN = 6V, ILOAD = 100mA, full temp range (l) | 4 | |
| Feedback Voltage Line Regulation (LT8609/LT8609A) | 0.004 | 0.02 | %/V | VIN = 4.0V to 40V, full temp range (l) | 4 | ||
| Feedback Pin Input Current | -20 | 20 | nA | VFB = 1.0V, full temp range (l) | 4 | ||
| Minimum On-Time, SYNC = 0V | 45 | 75 | ns | ILOAD = 1.5A, SYNC = 0V, full temp range (l) | 4 | ||
| Minimum On-Time, SYNC = 1.9V | 45 | 60 | ns | ILOAD = 1.5A, SYNC = 1.9V, full temp range (l) | 4 | ||
| Minimum Off Time | 90 | 130 | ns | 4 | |||
| Oscillator Frequency (LT8609/LT8609A), RT = 221k | 155 | 200 | 245 | kHz | RT = 221k, ILOAD = 0.5A, full temp range (l) | 5 | |
| Oscillator Frequency (LT8609/LT8609A), RT = 60.4k | 640 | 700 | 760 | kHz | RT = 60.4k, ILOAD = 0.5A, full temp range (l) | 5 | |
| Oscillator Frequency (LT8609/LT8609A), RT = 18.2k | 1.925 | 2 | 2.075 | MHz | RT = 18.2k, ILOAD = 0.5A, full temp range (l) | 5 | |
| Top Power NMOS Current Limit | 3.4 | 4.5 | 5.7 | A | full temp range (l) | 5 | |
| EN/UV Pin Threshold, EN/UV Rising | 0.99 | 1.05 | 1.11 | V | EN/UV Rising, full temp range (l) | 5 | |
| EN/UV Pin Current (LT8609/LT8609A) | -20 | 20 | nA | VEN/UV = 2V, full temp range (l) | 5 | ||
| PG Upper Threshold Offset from VFB (LT8609/LT8609A) | 5 | 8.5 | 13 | % | VFB Rising, full temp range (l) | 5 | |
| PG Lower Threshold Offset from VFB (LT8609/LT8609A) | 5 | 8.5 | 13 | % | VFB Falling, full temp range (l) | 5 | |
| PG Leakage | -200 | 200 | nA | VPG = 42V, full temp range (l) | 5 | ||
| PG Pull-Down Resistance | 550 | 1200 | Ω | VPG = 0.1V | 5 | ||
| Sync Low Input Voltage (LT8609/LT8609A) | 0.4 | 0.9 | V | full temp range (l) | 5 | ||
| Sync High Input Voltage (LT8609/LT8609A) | 2.7 | 3.2 | V | INTVCC = 3.5V, full temp range (l) | 5 | ||
| TR/SS Source Current | 1 | 2 | 3 | µA | full temp range (l) | 5 | |
| TR/SS Pull-Down Resistance | 300 | 900 | Ω | Fault Condition, TR/SS = 0.1V | 5 | ||
| Spread Spectrum Modulation Frequency (LT8609/LT8609A) | 1 | 3 | 6 | kHz | VSYNC = 3.3V | 5 | |
| FB, TR/SS pin voltage (absolute maximum) | 4 | V | FB, TR/SS | 2 | |||
| SYNC, VOUT pin voltage (absolute maximum) | 6 | V | SYNC, VOUT | 2 | |||
| Operating Junction Temperature Range (LT8609I) | -40 | 125 | °C | LT8609I/LT8609AI/LT8609BI | 2 | ||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Thermal Resistance, Junction-to-Ambient (MSE package) | θJA | 40 | °C/W | 10-Lead Plastic MSOP (MSE package) | 2 |
CAD (KiCad official)
- Symbol:
LT8609IMSE#PBF - Footprint:
Package_SO:MSOP-10-1EP_3x3mm_P0.5mm_EP1.68x1.88mm - 3D model: MSOP-10-EP (KiCad packages3D, STEP)
- 3D model files:
lt8609imse-pbf-etched.step/lt8609imse-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt8609imse-pbf.step/lt8609imse-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (30 pp, sha256
bb514bf594e97238, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).