3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownHG24C04CM
HGSEMI · EEPROM · SOP-8
HG24C04CM from HGSEMI, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | No connect pin; the datasheet pin diagram shows pin 1 as NC and gives no function for it. |
| 2 | E1 | input | Device address input that can be tied to VCC or GND in any combination, and is internally pulled down to GND if left floating. |
| 3 | E2 | input | Device address input that can be tied to VCC or GND in any combination, and is internally pulled down to GND if left floating. |
| 4 | GND | power_in | Ground reference for the power supply, to be connected to system ground. |
| 5 | SDA | bidirectional | Serial data pin, an open-drain bidirectional input/output used to transfer data to and from the device. |
| 6 | SCL | input | Serial clock input that controls data flow, with input data latched on the rising edge and output data clocked out on the falling edge of SCL. |
| 7 | WP | input | Write protection input that makes the memory read-only when tied to VCC, enables writes when tied to GND, and is internally pulled down to GND if left floating. |
| 8 | VCC | power_in | Device power supply pin, with a supply range of 1.7V to 5.5V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | HGSEMI |
| Package | SOP-8 |
| Category | Memory |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Read supply current at 1MHz, VCC=1.7V | ICC1 | 0.1 | mA | VCC=1.7V, Read at 1MHz | 18 | ||
| Read supply current at 400kHz, VCC=5.5V | ICC1 | 0.4 | mA | VCC=5.5V, Read at 400 kHz | 18 | ||
| Read supply current at 1MHz, VCC=5.5V | ICC1 | 0.5 | mA | VCC=5.5V, Read at 1MHz | 18 | ||
| Write supply current | ICC2 | 1 | mA | VCC=5.5V, Write at 400 kHz | 18 | ||
| Standby current | ISB | 1 | μA | VCC = 1.7V, VIN = VCC or GND | 18 | ||
| Input leakage current | ILI | 1 | μA | VIN = VCC or GND | 18 | ||
| Output leakage current | ILO | 1 | μA | VOUT = VCC or GND | 18 | ||
| Input low-level voltage (SDA, SCL) | VIL | -0.5 | 0.3 | V | Max printed as 0.3*VCC | 18 | |
| Input high-level voltage (SDA, SCL) | VIH | 0.7 | 5.5 | V | Min printed as 0.7*VCC; max printed as VCC+0.5 (value shown is the VCC max of 5.5 V range, not the +0.5 offset) | 18 | |
| Low-level output voltage | VOL1 | 0.4 | V | VCC > 2V, IOL= 3mA | 18 | ||
| Low-level output voltage | VOL2 | 0.2 | V | VCC ≤ 2V, IOL= 2mA | 18 | ||
| Clock frequency, SCL (Fast) | fSCL | 400 | kHz | Fast, VCC = 1.7V to 5.5V | 19 | ||
| Clock frequency, SCL (High Speed) | fSCL | 1000 | kHz | High Speed, VCC = 1.7V to 5.5V | 19 | ||
| Clock pulse width low (Fast) | tLOW | 1300 | ns | Fast, VCC = 1.7V to 5.5V | 19 | ||
| Clock pulse width low (High Speed) | tLOW | 600 | ns | High Speed, VCC = 1.7V to 5.5V | 19 | ||
| Clock pulse width high (Fast) | tHIGH | 600 | ns | Fast, VCC = 1.7V to 5.5V | 19 | ||
| Clock pulse width high (High Speed) | tHIGH | 260 | ns | High Speed, VCC = 1.7V to 5.5V | 19 | ||
| SDA rise time (Fast) | tR | 300 | ns | Fast; ensured by characterization only (note 1) | 19 | ||
| SDA rise time (High Speed) | tR | 300 | ns | High Speed; ensured by characterization only (note 1) | 19 | ||
| SDA(Out) fall time (Fast) | tF | 300 | ns | Fast; ensured by characterization only (note 1) | 19 | ||
| SDA(Out) fall time (High Speed) | tF | 100 | ns | High Speed; ensured by characterization only (note 1) | 19 | ||
| Start hold time (Fast) | tHD.STA | 600 | ns | Fast, VCC = 1.7V to 5.5V | 19 | ||
| Start hold time (High Speed) | tHD.STA | 250 | ns | High Speed, VCC = 1.7V to 5.5V | 19 | ||
| Start setup time (Fast) | tSU.STA | 600 | ns | Fast, VCC = 1.7V to 5.5V | 19 | ||
| Start setup time (High Speed) | tSU.STA | 250 | ns | High Speed, VCC = 1.7V to 5.5V | 19 | ||
| Stop setup time (Fast) | tSU.STO | 600 | ns | Fast, VCC = 1.7V to 5.5V | 19 | ||
| Stop setup time (High Speed) | tSU.STO | 250 | ns | High Speed, VCC = 1.7V to 5.5V | 19 | ||
| Bus free time between Stop and Start (Fast) | tBUF | 1300 | ns | Fast, VCC = 1.7V to 5.5V | 19 | ||
| Bus free time between Stop and Start (High Speed) | tBUF | 500 | ns | High Speed, VCC = 1.7V to 5.5V | 19 | ||
| Data in hold time (Fast) | tHD.DI | 0 | ns | Fast, VCC = 1.7V to 5.5V | 19 | ||
| Data in hold time (High Speed) | tHD.DI | 0 | ns | High Speed, VCC = 1.7V to 5.5V | 19 | ||
| Data in setup time (Fast) | tSU.DAT | 100 | ns | Fast, VCC = 1.7V to 5.5V | 19 | ||
| Data in setup time (High Speed) | tSU.DAT | 50 | ns | High Speed, VCC = 1.7V to 5.5V | 19 | ||
| Data out hold time (Fast) | tHD.DAT | 50 | ns | Fast, VCC = 1.7V to 5.5V | 19 | ||
| Data out hold time (High Speed) | tHD.DAT | 50 | ns | High Speed, VCC = 1.7V to 5.5V | 19 | ||
| SCL low to data out valid (Fast) | tAA | 100 | 900 | ns | Fast, VCC = 1.7V to 5.5V | 19 | |
| SCL low to data out valid (High Speed) | tAA | 50 | 500 | ns | High Speed, VCC = 1.7V to 5.5V | 19 | |
| WP pin setup time (Fast) | tSU.WP | 1200 | ns | Fast, VCC = 1.7V to 5.5V | 19 | ||
| WP pin setup time (High Speed) | tSU.WP | 600 | ns | High Speed, VCC = 1.7V to 5.5V | 19 | ||
| WP pin hold time (Fast) | tHD.WP | 1200 | ns | Fast, VCC = 1.7V to 5.5V | 19 | ||
| WP pin hold time (High Speed) | tHD.WP | 600 | ns | High Speed, VCC = 1.7V to 5.5V | 19 | ||
| Write cycle time | tWR | 5 | ms | 19 | |||
| Noise suppression time | tI | 50 | ns | 19 | |||
| Power-On Reset Time | tPOR | 10 | ms | 6 | |||
| Power-On Reset Voltage | VPOR | 1.5 | V | 6 | |||
| Brown-out Reset Voltage | VBOR | 0.8 | V | 6 | |||
| Time from Power-On to First Command | tINIT | 10 | ms | 6 | |||
| Warm Power Cycle Off Time | tPOFF | 1 | ms | 6 | |||
| Input/output capacitance (SDA) | CI/O | 8 | pF | VI/O = 0V; TA = +25°C, fC = 1MHz | 20 | ||
| Input capacitance (other pins) | CIN | 6 | pF | VIN = 0V; TA = +25°C, fC = 1MHz | 20 | ||
| Data retention | DR | 200 | year | TA = +25°C | 20 | ||
| Ambient temperature with power applied | TA | -40 | 105 | °C | 18 | ||
| Storage temperature | TSTG | -65 | 150 | °C | 18 | ||
| Supply voltage | VCC | -0.5 | 6 | V | 18 | ||
| Voltage on input pins | VIN | -0.5 | 6 | V | 18 | ||
| Electrostatic pulse (human body model) | VESD | 6000 | V | 18 | |||
| Lead temperature (soldering, 10 seconds) | TL | 260 | °C | 10 seconds soldering | 18 | ||
| Supply voltage | VCC | 1.7 | 5.5 | V | Operating range TA = -40°C to +105°C | 18 | |
| Ambient operating temperature range | TA | -40 | 105 | °C | VCC = 1.7V to 5.5V | 18 |
CAD (KiCad official)
- Symbol:
HG24C04CM - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOP-8 (KiCad packages3D, STEP)
- 3D model files:
hg24c04cm-etched.step/hg24c04cm-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);hg24c04cm.step/hg24c04cm.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: HGSEMI datasheet (27 pp, sha256
8bd31d1acd5458af, retrieved 2026-10-28, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text+vision), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).