component

TPIC46L02DBR

Public Made by Adom

by adom

Texas Instruments Gate Drivers, SSOP-28-208mil. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.

componentmotor driver icstpic46l02dbrfactory-2.0.0extractor-text
Overview Files Discover Packages Releases Dependencies Issues Breadcrumbs Pull Requests Activity

3D Model

Open in new tab ↗
Loads on click. Unloads only if this page sits in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads on click. Unloads only if this page sits in the background.

PCB Footprint

Open full view ↗
Loads on click. Unloads only if this page sits in the background.

Datasheet

Open in new tab ↗
Loads on click. Unloads only if this page sits in the background.
Download PDF
Contents

README

markdown

TPIC46L02DBR

Texas Instruments · Gate Drivers · SSOP-28-208mil

TPIC46L02DBR from Texas Instruments, in a SSOP-28-208mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 FLT output Open-drain fault flag output for shorted-load, open-load, over-battery voltage, and under-battery voltage faults; requires external pullup resistor.
2 VCOMPEN input Fault reference voltage selector input; connect to GND for internal 1.25-V reference or to VCC for external VCOMP reference.
3 VCOMP input External fault reference voltage input for shorted- and open-load fault detection.
4 IN0 input Parallel gate driver input for GATE0; CMOS-compatible with hysteresis.
5 IN1 input Parallel gate driver input for GATE1; CMOS-compatible with hysteresis.
6 IN2 input Parallel gate driver input for GATE2; CMOS-compatible with hysteresis.
7 IN3 input Parallel gate driver input for GATE3; CMOS-compatible with hysteresis.
8 IN4 input Parallel gate driver input for GATE4; CMOS-compatible with hysteresis.
9 IN5 input Parallel gate driver input for GATE5; CMOS-compatible with hysteresis.
10 CS input Chip select input; high-to-low transition enables SDO and latches fault data, low-to-high transition transfers serial data to output buffer.
11 SDO tri_state 3-state serial data output for fault data and cascaded operation; taken to high-impedance state when CS is high.
12 SDI input Serial data input for output control data clocked into the serial register; setup time 10 ns before SCLK rising edge, hold time 10 ns after.
13 SCLK input Serial clock input that clocks the shift register; serial data clocked on falling edge.
14 VCC power_in Logic supply voltage input; recommended operating range 4.5 V to 5.5 V.
15 GND power_in Ground and substrate connection.
16 GATE5 output Gate drive output derived from VBAT supply; internal clamps prevent voltage from exceeding FET VGS rating.
17 DRAIN5 input FET drain input used for open-load and short-circuit fault detection and inductive transient protection; voltage range −0.3 V to 60 V.
18 GATE4 output Gate drive output derived from VBAT supply; internal clamps prevent voltage from exceeding FET VGS rating.
19 DRAIN4 input FET drain input used for open-load and short-circuit fault detection and inductive transient protection; voltage range −0.3 V to 60 V.
20 DRAIN3 input FET drain input used for open-load and short-circuit fault detection and inductive transient protection; voltage range −0.3 V to 60 V.
21 GATE3 output Gate drive output derived from VBAT supply; internal clamps prevent voltage from exceeding FET VGS rating.
22 GATE2 output Gate drive output derived from VBAT supply; internal clamps prevent voltage from exceeding FET VGS rating.
23 DRAIN2 input FET drain input used for open-load and short-circuit fault detection and inductive transient protection; voltage range −0.3 V to 60 V.
24 DRAIN1 input FET drain input used for open-load and short-circuit fault detection and inductive transient protection; voltage range −0.3 V to 60 V.
25 GATE1 output Gate drive output derived from VBAT supply; internal clamps prevent voltage from exceeding FET VGS rating.
26 DRAIN0 input FET drain input used for open-load and short-circuit fault detection and inductive transient protection; voltage range −0.3 V to 60 V.
27 GATE0 output Gate drive output derived from VBAT supply; internal clamps prevent voltage from exceeding FET VGS rating.
28 VBAT power_in Battery supply voltage input; recommended operating range 8 V to 24 V.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package SSOP-28-208mil
Category Motor Driver ICs
Pins 28

CAD (KiCad official)

  • Symbol: TPIC46L02DBR
  • Footprint: Package_SO:SSOP-28_5.3x10.2mm_P0.65mm
  • 3D model: SSOP-28-208mil (KiCad packages3D, STEP)
  • 3D model files: tpic46l02dbr-etched.step / tpic46l02dbr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tpic46l02dbr.step / tpic46l02dbr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (25 pp, sha256 3c3669b56023cbd2, retrieved 2026-10-07, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF