component
TPS61006DGSR
Public Made by Adomby adom
Texas Instruments DC-DC Converters, VSSOP-10-0.5mm. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownTPS61006DGSR
Texas Instruments · DC-DC Converters · VSSOP-10-0.5mm
TPS61006DGSR from Texas Instruments, in a VSSOP-10-0.5mm. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | Chip-enable input: the converter is switched on when EN is high and switched off (shutdown) when EN is connected to ground. |
| 2 | COMP | passive | Error-amplifier compensation pin; connect an R-C-C network here to set the frequency response of the control loop. |
| 3 | FB | unconnected | Feedback input for adjustable output only (TPS61000); for the fixed-output TPS61006 this pin must be left unconnected. |
| 4 | GND | power_in | Ground pin. |
| 5 | VOUT | power_out | Output voltage; for the fixed-output versions the integrated resistive divider is connected to this pin. |
| 6 | VBAT | power_in | Supply pin for the converter; the device starts into a full load from supply voltages as low as 0.9 V and operates down to 0.8 V. |
| 7 | SW | input | Switch input pin; the node between the inductor and the anode of the rectifier diode connects to this pin, with absolute maximum SW voltage of VOUT + 0.7 V. |
| 8 | NC/FBGND | unconnected | Not connected on the TPS61006; it serves as the ground pin for the feedback resistor divider on the TPS61007 only. |
| 9 | LBI | input | Low-battery detector input; LBO is pulled low when LBI drops below the 500 mV threshold, and LBI must be tied to GND or VBAT if unused and must not be left floating. |
| 10 | LBO | output | Open-drain low-battery detector output that is pulled low when LBI falls below 500 mV; a pull-up resistor should be connected between LBO and VOUT. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VSSOP-10-0.5mm |
| Category | Power Supply Chip |
| Pins | 10 |
CAD (KiCad official)
- Symbol:
TPS61006DGSR - Footprint:
Package_SO:MSOP-10_3x3mm_P0.5mm - 3D model: VSSOP-10-0.5mm (KiCad packages3D, STEP)
- 3D model files:
tps61006dgsr-etched.step/tps61006dgsr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps61006dgsr.step/tps61006dgsr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (31 pp, sha256
2cac6e085a4ce051, retrieved 2026-10-08, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).