component
CM1003-CPD
Public Made by Adomby adom
iCM(创芯微) Battery Management, DFN-6L(1.6x1.9). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownCM1003-CPD
iCM(创芯微) · Battery Management · DFN-6L(1.6x1.9)
CM1003-CPD from iCM(创芯微), in a DFN-6L(1.6x1.9). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | No internal connection; leave unconnected. |
| 2 | CO | output | Charge MOSFET control terminal: CO goes high in normal operation and switches low to turn off charging on overcharge (delay TOC 1000 ms typ) or charge overcurrent (VCHA -0.060 V typ, delay TCHA 16 ms typ). |
| 3 | DO | output | Discharge MOSFET control terminal: DO goes high in normal operation and switches low to turn off discharging on overdischarge (VOD 2.500 V typ, delay TOD 64 ms typ), discharge overcurrent (VEC 0.060 V typ, delay TEC 16 ms typ) or load short circuit (VSHORT 0.165 V typ, delay TSHORT 280 µs typ). |
| 4 | VSS | power_in | Power ground, connected to the negative terminal of the supply (battery); the reference for all detection thresholds. |
| 5 | VDD | power_in | Power supply input, connected to the positive terminal of the supply (battery); the absolute maximum VDD to VSS voltage is VSS-0.3 V to VSS+8.0 V. |
| 6 | VM | input | Charge/discharge current sense terminal, connected to the negative terminal of the charger or load; absolute voltage range is VDD-28 V to VDD+0.3 V. |
| 7 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | iCM(创芯微) |
| Package | DFN-6L(1.6x1.9) |
| Category | Power Management (PMIC) |
| Pins | 7 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 正常工作电流 (Normal operating current) | IOPE | 0.9 | 1.5 | 3 | μA | Ta=+25°C; VDD=3.5V, VVM=0V | 7 |
| 休眠电流 (Power-down current) | IPDN | 50 | nA | Ta=+25°C; VDD=VVM=1.5V | 7 | ||
| 过充电保护电压 (Overcharge detection voltage) | VOC | 4.5 | 4.52 | 4.54 | V | Ta=+25°C; VDD=3.5 → 4.8V | 7 |
| 过充电解除电压 (Overcharge release voltage) | VOCR | 4.275 | 4.32 | 4.365 | V | Ta=+25°C; VDD=4.8 → 3.5V | 7 |
| 过放电保护电压 (Overdischarge detection voltage) | VOD | 2.45 | 2.5 | 2.55 | V | Ta=+25°C; VDD=3.5 → 2.0V | 7 |
| 过放电解除电压 (Overdischarge release voltage) | VODR | 2.8 | 2.9 | 3 | V | Ta=+25°C; VDD=2.0 → 3.5V | 7 |
| 放电过流保护电压 (Discharge overcurrent detection voltage) | VEC | 0.055 | 0.06 | 0.065 | V | Ta=+25°C; VM-VSS=0 → 0.30V | 7 |
| 短路保护电压 (Load short-circuit detection voltage) | VSHORT | 0.152 | 0.165 | 0.178 | V | Ta=+25°C; VM-VSS=0 → 1.5V | 7 |
| 充电过流保护电压 (Charge overcurrent detection voltage) | VCHA | -0.065 | -0.06 | -0.055 | V | Ta=+25°C; VSS-VM=0 → 0.30V | 7 |
| 放电过流解除电压, offset from VDD (Discharge overcurrent release voltage) | VRIOV | -1.4 | -1 | -0.6 | V | Ta=+25°C | 7 |
| 过充电保护延时 (Overcharge detection delay) | TOC | 700 | 1000 | 1300 | ms | Ta=+25°C; VDD=3.5 → 4.8V | 7 |
| 过放电保护延时 (Overdischarge detection delay) | TOD | 44.8 | 64 | 83.2 | ms | Ta=+25°C; VDD=3.5 → 2.0V | 7 |
| 放电过流保护延时 (Discharge overcurrent detection delay) | TEC | 11.2 | 16 | 20.8 | ms | Ta=+25°C; VM-VSS=0 →VEC+0.1V | 7 |
| 充电过流保护延时 (Charge overcurrent detection delay) | TCHA | 11.2 | 16 | 20.8 | ms | Ta=+25°C; VSS-VM=0 → 0.30V | 7 |
| 短路保护延时 (Load short-circuit detection delay) | TSHORT | 140 | 280 | 504 | μs | Ta=+25°C; VM-VSS=0 → 1.5V | 7 |
| VDD端子-VM端子间电阻 (VDD-VM internal resistance) | RVMC | 750 | 1500 | 3000 | kΩ | Ta=+25°C; VDD=1.8V, VVM=0V | 7 |
| VM端子-VSS端子间电阻 (VM-VSS internal resistance) | RVMS | 10 | 20 | 30 | kΩ | Ta=+25°C; VDD=3.5V, VVM=1.0V | 7 |
| CO端子电阻“H” (CO output resistance, high) | RCOH | 5 | 10 | 20 | kΩ | Ta=+25°C | 7 |
| CO端子电阻“L” (CO output resistance, low) | RCOL | 5 | 10 | 20 | kΩ | Ta=+25°C | 7 |
| DO端子电阻“H” (DO output resistance, high) | RDOH | 5 | 10 | 20 | kΩ | Ta=+25°C | 7 |
| DO端子电阻“L” (DO output resistance, low) | RDOL | 5 | 10 | 20 | kΩ | Ta=+25°C | 7 |
| 禁止向0V电池充电的电池电压 (0V battery charge inhibit voltage) | V0IN | 0.9 | 1.2 | 1.5 | V | Ta=+25°C; 禁止向0V电池充电功能 | 7 |
| 正常工作电流 (Normal operating current) | IOPE | 0.6 | 1.5 | 5 | μA | Ta=-20°C~+60°C; VDD=3.5V, VVM=0V | 8 |
| 休眠电流 (Power-down current) | IPDN | 150 | nA | Ta=-20°C~+60°C; VDD=VVM=1.5V | 8 | ||
| 过充电保护电压 (Overcharge detection voltage) | VOC | 4.48 | 4.52 | 4.56 | V | Ta=-20°C~+60°C; VDD=3.5 → 4.8V | 8 |
| 过充电解除电压 (Overcharge release voltage) | VOCR | 4.245 | 4.32 | 4.395 | V | Ta=-20°C~+60°C; VDD=4.8 → 3.5V | 8 |
| 过放电保护电压 (Overdischarge detection voltage) | VOD | 2.42 | 2.5 | 2.58 | V | Ta=-20°C~+60°C; VDD=3.5 → 2.0V | 8 |
| 过放电解除电压 (Overdischarge release voltage) | VODR | 2.78 | 2.9 | 3.02 | V | Ta=-20°C~+60°C; VDD=2.0 → 3.5V | 8 |
| 放电过流保护电压 (Discharge overcurrent detection voltage) | VEC | 0.05 | 0.06 | 0.07 | V | Ta=-20°C~+60°C; VM-VSS=0 → 0.30V | 8 |
| 短路保护电压 (Load short-circuit detection voltage) | VSHORT | 0.139 | 0.165 | 0.191 | V | Ta=-20°C~+60°C; VM-VSS=0 → 1.5V | 8 |
| 充电过流保护电压 (Charge overcurrent detection voltage) | VCHA | -0.07 | -0.06 | -0.05 | V | Ta=-20°C~+60°C; VSS-VM=0 → 0.30V | 8 |
| 放电过流解除电压, offset from VDD (Discharge overcurrent release voltage) | VRIOV | -1.6 | -1 | -0.4 | V | Ta=-20°C~+60°C | 8 |
| 过充电保护延时 (Overcharge detection delay) | TOC | 500 | 1000 | 2000 | ms | Ta=-20°C~+60°C; VDD=3.5 → 4.8V | 8 |
| 过放电保护延时 (Overdischarge detection delay) | TOD | 32 | 64 | 128 | ms | Ta=-20°C~+60°C; VDD=3.5 → 2.0V | 8 |
| 放电过流保护延时 (Discharge overcurrent detection delay) | TEC | 8 | 16 | 32 | ms | Ta=-20°C~+60°C; VM-VSS=0 →VEC+0.1V | 8 |
| 充电过流保护延时 (Charge overcurrent detection delay) | TCHA | 8 | 16 | 32 | ms | Ta=-20°C~+60°C; VSS-VM=0 → 0.30V | 8 |
| 短路保护延时 (Load short-circuit detection delay) | TSHORT | 112 | 280 | 616 | μs | Ta=-20°C~+60°C; VM-VSS=0 → 1.5V | 8 |
| VDD端子-VM端子间电阻 (VDD-VM internal resistance) | RVMC | 500 | 1500 | 6000 | kΩ | Ta=-20°C~+60°C; VDD=1.8V, VVM=0V | 8 |
| VM端子-VSS端子间电阻 (VM-VSS internal resistance) | RVMS | 7.5 | 20 | 40 | kΩ | Ta=-20°C~+60°C; VDD=3.5V, VVM=1.0V | 8 |
| CO端子电阻“H” (CO output resistance, high) | RCOH | 2.5 | 10 | 30 | kΩ | Ta=-20°C~+60°C | 8 |
| CO端子电阻“L” (CO output resistance, low) | RCOL | 2.5 | 10 | 30 | kΩ | Ta=-20°C~+60°C | 8 |
| DO端子电阻“H” (DO output resistance, high) | RDOH | 2.5 | 10 | 30 | kΩ | Ta=-20°C~+60°C | 8 |
| DO端子电阻“L” (DO output resistance, low) | RDOL | 2.5 | 10 | 30 | kΩ | Ta=-20°C~+60°C | 8 |
| 禁止向0V电池充电的电池电压 (0V battery charge inhibit voltage) | V0IN | 0.6 | 1.2 | 1.8 | V | Ta=-20°C~+60°C; 禁止向0V电池充电功能 | 8 |
| VDD-VSS输入电压 (VDD-VSS input voltage; range VSS-0.3 to VSS+8.0) | VDD | -0.3 | 8 | V | Ta=+25°C (unless noted) | 6 | |
| VM输入端子电压 (VM input terminal voltage; range VDD-28 to VDD+0.3) | VVM | -28 | 0.3 | V | Ta=+25°C (unless noted) | 6 | |
| CO输出端子电压 (CO output terminal voltage; range VVM-0.3 to VDD+0.3) | VCO | -0.3 | 0.3 | V | Ta=+25°C (unless noted) | 6 | |
| DO输出端子电压 (DO output terminal voltage; range VSS-0.3 to VDD+0.3) | VDO | -0.3 | 0.3 | V | Ta=+25°C (unless noted) | 6 | |
| 工作温度范围 (Operating temperature range) | TOPR | -40 | 85 | °C | 6 | ||
| 储存温度范围 (Storage temperature range) | TSTG | -55 | 125 | °C | 6 |
CAD (KiCad official)
- Symbol:
CM1003-CPD - Footprint:
Package_DFN_QFN:DFN-6-1EP_2x1.6mm_P0.5mm_EP1.15x1.3mm - 3D model: DFN-6L(1.6x1.9), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.9 mm nominal QFN height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files:
cm1003-cpd-etched.step/cm1003-cpd-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);cm1003-cpd.step/cm1003-cpd.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: iCM(创芯微) datasheet (21 pp, sha256
8ae589e6fa45f392, retrieved 2026-10-17, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).