Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

BMP581

Bosch Sensortec · Pressure Sensors · LGA-10(2x2)

BMP581 from Bosch Sensortec, in a LGA-10(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.

Pinout

Pin Name Type Function
1 VDDIO power_in Digital interface supply VDDIO, connected to the host interface supply.
2 SCK input Serial clock input, used in both SPI 4-wire and SPI 3-wire modes.
3 VSS power_in Ground; all VSS pins must be connected to GND.
4 SDI bidirectional Serial data input in SPI 4-wire mode and bidirectional SDI/SDO data pad in SPI 3-wire mode; it must be tied to low or high and not left floating.
5 SDO bidirectional Serial data output in SPI 4-wire mode; in SPI 3-wire mode it must be left floating (DNC).
6 CSB input Chip select input, active low.
7 INT output Interrupt output to the host INT input; it may be connected to GND or left unconnected only with INT_CONFIG.int_en disabled or the recommended settings.
8 VSS power_in Ground; all VSS pins must be connected to GND.
9 VSS power_in Ground; all VSS pins must be connected to GND.
10 VDD power_in Analog supply VDD for the sensor.

Key specifications

Parameter Value
Manufacturer Bosch Sensortec
Package LGA-10(2x2)
Category Sensors
Pins 10

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Relative pressure accuracy Ap_rel -0.4 0.4 Pa 900, 1100 hPa, 25 °C, 1 kPa steps 8
Absolute pressure accuracy Ap_abs -30 30 Pa 300, 1100 hPa, -5, 65 °C, including TCO 8
Absolute accuracy pressure (full range) Ap_abs_full_range -75 75 Pa 300, 1100 hPa, -40, 85 °C, incl. solder drift, TCO after qualification 9
Offset temperature coefficient TCO -0.5 0.5 Pa/K 300, 1100 hPa, -5, 65 °C, 10 K steps 9
Long term drift ∆Pstab_long -10 10 Pa Drift during 1 year 9
Short term drift ∆Pstab_short -1.5 1.5 Pa Drift during 24 h at constant pressure and temperature 9
Solder drift -30 30 Pa 5x reflow soldering after storage in standard conditions (25 °C / 100 kPa) 9
Absolute accuracy temperature At_abs -0.5 0.5 K -5 .. 55°C 10
Absolute accuracy temperature full range At_abs_full -0.5 0.5 K -40 .. 85°C 10
Pressure noise low power Vp_low_power 0.78 0.95 PaRMS OSR set to lowest power 8
Pressure noise high resolution Vp_hi_res 0.21 0.25 PaRMS OSR set to high resolution 8
Power supply voltage VDD 1.71 3.6 V 10
Power supply voltage I/Os VDDIO 1.08 3.6 V 10
Supply ramp time t_VDDramp & t_VDDIOramp 0.01 10 ms 10% to 90% of target voltage 10
Operational temperature range TOP_full -40 85 °C 10
ODR accuracy -10 10 % -40..85°C 10
Power-up time t_powup 2 ms Time to first communication after both VDD > VDDmin and VDDIO > VDDIOmin 10
Start-up time from STANDBY t_startup 3 ms Time from mode change to start of measurement 11
Start-up time from DEEP STANDBY tstartup_deep 4 ms Time from mode change to start of measurement 11
Re-configuration time treconf 3 ms Time from configuration change in NORMAL or CONTINUOUS mode to start of first measurement 11
Re-configuration time (deep) treconf_deep 4 ms Time from configuration change in NORMAL or CONTINUOUS mode to start of first measurement 11
Time to standby tstandby 2.5 ms Time from any mode to STANDBY 11
Soft reset duration tsoft_res 2 ms Time from trigger of soft reset until device ready 11
I3C interface clock fi3C 0.1 12.5 12.9 MHz @ VDDIO > 1.62 V - Normal Mode & Fast Mode @ Cbus < 550pF - Fast Mode + @Cbus > 100pF 11
SPI interface clock fspi 12 MHz @ VDDIO ≥ 1.62 V, Cbus ≤ 80 pF 4-wire/ 3-wire; modes 0 and 3 11
SPI interface clock low voltage fspi_lowv 7 MHz @ VDDIO ≤ 1.62 V, Cbus ≤ 40 pF 4-wire/ 3-wire; modes 0 and 3 11
Peak current ipeak 260 μA maximum DC current 12
Deep Standby current 0.55 μA 25 °C and VDDIO=VDD=1.8 V 12
Deep Standby current 1.5 μA 55 °C and VDDIO=VDD=1.8 V 12
Standby current 1 μA 25 °C and VDDIO=VDD=1.8 V 12
Standby current 3.5 μA 55 °C and VDDIO=VDD=1.8 V 12
Current consumption low power mode 1.3 μA OSR set to lowest power, Low Power Mode ODR=1 Hz 25 °C 12
INT pulse length tint_pulse 90 105 121 μs Pulse length in pulsed mode 12
INT minimum deassert time tint_deassert 90 105 121 μs Minimum time between INT pin assert 12
Maximum output rate (ODR) 489 Hz in CONTINUOUS mode, pressure and temperature measured 12
Output data rate (ODR) range 0.125 240 Hz in NORMAL mode 12
Pull-up resistance at CSB pin RPU_CSB 74 100 131 kOhm I2C mode, relevant for interface mode selection 13
Storage temperature -40 125 °C ≤ 65 % r.h. Standard conditions: + 25°C and 40% r.h. 13
Supply voltage VDD -0.3 4.3 V 13
Max voltage at I/O pins VSSIO -0.3 V Max voltage at I/O pins, VSSIO-0.3 V to VDDIO + 0.3 V 13

CAD (Adom-generated)

  • Symbol: BMP581
  • Footprint: Adom_Gen:BOSCH_SENSORTECH_BMP581_1a03d8
  • 3D model: generated to fit the land (STEP)
  • 3D model files: bmp581-etched.step / bmp581-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); bmp581.step / bmp581.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Bosch Sensortec datasheet (75 pp, sha256 ddcf4202c4fdf2ab, retrieved 2026-11-17, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land.

Datasheet PDF