3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownSY5867FAC
Silergy Corp · LED Drivers · SO-8
SY5867FAC from Silergy Corp, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Ground pin of the converter, which is the reference for the internal circuit and for the signal and setting pins. |
| 2 | ISET | passive | Source current setting pin that is a 1.5V voltage source, with the DIMI source current set by IDIMI = 5×1.5 / RISET. |
| 3 | VLOW | passive | Zero coordinate setting pin that sets the lowest input voltage corresponding to 0% duty, with a setting range of 0 to VISET. |
| 4 | FSET | passive | Dimming frequency setting pin, where an external capacitor sets the frequency of the DIMO PWM output through a 20uA charge and discharge current. |
| 5 | DIMI | bidirectional | Dimming input accepting a 0/1~10V analog signal, a resistor or a PWM signal, with the ISET-set source current flowing out of this pin for passive dimmers. |
| 6 | DIMO | output | Dimming output pin that outputs a PWM signal to drive an opto-coupler or dimmable IC for isolated dimming. |
| 7 | HLCLP | passive | High and low clamp mode setting pin, where a voltage above 100mV during start-up selects low clamp mode and otherwise high clamp mode is used. |
| 8 | VIN | power_in | Power supply pin for the IC, with a turn-on threshold of 8.4V to 10.2V and a recommended operating voltage up to 55V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Silergy Corp |
| Package | SO-8 |
| Category | Display Modules / LED Drivers / Display Drivers |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Absolute maximum VIN voltage | VIN | -0.3 | 58 | V | 4 | ||
| Absolute maximum IIN current | IIN | 10 | mA | 4 | |||
| Absolute maximum ISET, FSET, VLOW voltage | -0.3 | 3.6 | V | 4 | |||
| Absolute maximum DIMI, DIMO voltage | 0.3 | 20 | V | 4 | |||
| Power dissipation SO8 | 0.8 | W | TA = 25°C | 4 | |||
| Maximum junction temperature | 125 | °C | 4 | ||||
| Lead temperature soldering | 260 | °C | 10 sec soldering | 4 | |||
| Storage temperature range | -65 | 150 | °C | 4 | |||
| Recommended VIN operating range | VIN | 55 | V | VVIN,ON~55V | 4 | ||
| Junction temperature range | -40 | 125 | °C | 4 | |||
| Package thermal resistance junction-to-ambient SO8 | θJA | 88 | °C/W | SO8 | 4 | ||
| Package thermal resistance junction-to-case SO8 | θJC | 45 | °C/W | SO8 | 4 | ||
| VIN voltage range | VVIN | 55 | V | VVIN_ON | 5 | ||
| VIN turn-on threshold | VVIN_ON | 8.4 | 9.2 | 10.2 | V | 5 | |
| VIN over voltage protection | VVIN_OVP | 52 | 55 | 59 | V | 5 | |
| Range of minimum dimming voltage | VLOW_Range | 0 | V | 5 | |||
| Ref voltage of ISET | VISET | 1.45 | 1.5 | 1.55 | V | 5 | |
| MAX DIMI source current | ISR_MAX | 1.85 | 2 | 2.15 | mA | ISET=3.75K | 5 |
| Maximum dimming voltage | VHIGH | 9.2 | 9.5 | 9.8 | V | 5 | |
| Max duty of PWM | DPWM_MAX | 99 | % | note 3 | 5 | ||
| Thermal shut down temperature | TSD | 145 | °C | 5 | |||
| PWM ON voltage threshold | VPWM_ON | 2.3 | V | 5 | |||
| PWM OFF voltage threshold | VPWM_OFF | 0.8 | V | 5 |
CAD (KiCad official)
- Symbol:
SY5867FAC - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SO-8 (KiCad packages3D, STEP)
- 3D model files:
sy5867fac-etched.step/sy5867fac-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sy5867fac.step/sy5867fac.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Silergy Corp datasheet (15 pp, sha256
4d43a00d0b297dc2, retrieved 2026-10-27, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusoff(skipped (clean text read)), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).