component
EG1252L
Public Made by Adomby adom
EG Micro AC-DC Controllers And Regulators, SOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownEG1252L
EG Micro · AC-DC Controllers And Regulators · SOP-8
EG1252L from EG Micro, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | FB | input | Feedback input: the PWM duty cycle is set by this pin's voltage together with the current-sense signal, with FB open-circuit voltage 5.3 V (typ.) and FB-to-GND short-circuit current 1.2 mA (typ.). |
| 2 | BO | input | Input voltage detection pin for input undervoltage protection, with a protection voltage VBO of 0.95 V and an internal 9 µA pull-down current source active when VBO is below 0.9 V. |
| 3 | CS | input | Current-sense input that reads the voltage across the external sense resistor for cycle-by-cycle overcurrent limiting, with Vcs(max) of 0.92 V min, 1 V typ and 1.08 V max and 250 ns leading-edge blanking. |
| 4 | RI | passive | Frequency-setting pin: an external resistor from RI to GND sets the switching frequency per Fosc(kHz) = 4200 / RI(kΩ), with an RI open-circuit voltage of 2 V. |
| 5 | GND | power_in | Chip ground. |
| 6 | OUT | output | Gate drive output for the power MOSFET, with a maximum of VCC + 0.3 V, a high-level output of 13 V (typ.) at 20 mA source and a low-level output of 0.3 V at 20 mA sink. |
| 7 | VCC | power_in | Supply pin with a 30 V absolute maximum, a 32 V (typ.) zener clamp at 10 mA, and 2.3 mA (typ.) operating current. |
| 8 | RT | input | Over-temperature protection pin: an external NTC thermistor sets the trip point, with an 80 µA internal current source flowing out of RT, protection entering at 1 V and releasing above 1.1 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | EG Micro |
| Package | SOP-8 |
| Category | Power Management (PMIC) |
| Pins | 8 |
CAD (KiCad official)
- Symbol:
EG1252L - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOP-8 (KiCad packages3D, STEP)
- 3D model files:
eg1252l-etched.step/eg1252l-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);eg1252l.step/eg1252l.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: EG Micro datasheet (11 pp, sha256
0ccb14070c4fa207, retrieved 2026-10-09, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).