3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMCP1824T-1802E
Microchip Tech · Linear Voltage Regulators (LDO) · SOT-23-5
MCP1824T-1802E from Microchip Tech, in a SOT-23-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Input voltage supply with an operating range of 2.1V to 6.0V; an input capacitor of 1 µF to 10 µF is recommended, especially when the source is remote or a battery. |
| 2 | GND | power_in | Ground pin that should be tied to an electrically quiet circuit ground for best noise and PSRR, and conducts only the LDO ground current. |
| 3 | SHDN | input | Active-low shutdown control input: a logic-high enables the LDO output and a logic-low disables it, pulling PWRGD low and reducing quiescent current to a typical 0.1 µA. |
| 4 | PWRGD | output | Open-drain power good output that indicates the output is within 92% (typical) of regulation, with a fixed 110 µs (typical) delay after power-up. |
| 5 | VOUT | power_out | Regulated LDO output that requires a minimum output capacitance of 1.0 µF for stability. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOT-23-5 |
| Category | Power Supply Chip |
| Pins | 5 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Operating Voltage | VIN | 2.1 | 6 | V | 7 | ||
| Output Voltage Range | VOUT | 0.8 | 5 | V | 7 | ||
| Voltage Regulation (fixed output, 2.5% tolerance option) | VOUT | -2.5 | 2.5 | % | Note 2; printed as VR - 2.5% to VR + 2.5%, VR = 1.8V | 8 | |
| Input Quiescent Current | Iq | 120 | 220 | µA | IL = 0 mA, VOUT = 0.8V to 5.0V | 7 | |
| Input Quiescent Current for SHDN Mode | ISHDN | 0.1 | 3 | µA | SHDN = GND | 7 | |
| Maximum Continuous Output Current | IOUT | 300 | mA | VIN = 2.1V to 6.0V; VR = 0.8V to 5.0V | 7 | ||
| Line Regulation | ΔVOUT/(VOUT x ΔVIN) | -0.17 | 0.05 | 0.17 | %/V | (Note 1) ≤ VIN ≤ 6V | 7 |
| Load Regulation | ΔVOUT/VOUT | -1 | 0.5 | 1 | % | IOUT = 1 mA to 300 mA; Note 4 | 7 |
| Dropout Voltage | VDROPOUT | 200 | 320 | mV | Note 5, IOUT = 300 mA, VIN(MIN) = 2.1V | 7 | |
| Maximum Pulsed Output Duty Cycle | IPULSE_DUTY | 60 | % | VIN = 2.1V to 6.0V, VR = 0.8V to 5.0V, IOUT = 500 mA, Period < 10 ms | 8 | ||
| Maximum Pulsed Output Period | IPULSE_PERIOD | 10 | ms | VIN = 2.1V to 6.0V, VR = 0.8V to 5.0V, IOUT = 500 mA | 8 | ||
| PWRGD Input Voltage Operating Range | VPWRGD_VIN | 1 | 6 | V | TA = +25°C | 8 | |
| PWRGD Input Voltage Operating Range | VPWRGD_VIN | 1.2 | 6 | V | TA = -40°C to +125°C | 8 | |
| PWRGD Threshold Voltage (Referenced to VOUT) | VPWRGD_TH | 89 | 92 | 95 | %VOUT | Falling Edge; VOUT < 2.5V Fixed, VOUT = Adj. | 8 |
| PWRGD Threshold Hysteresis | VPWRGD_HYS | 1 | 2 | 3 | %VOUT | 8 | |
| PWRGD Output Voltage Low | VPWRGD_L | 0.05 | 0.4 | V | IPWRGD SINK = 1.2 mA, ADJ = 0V | 8 | |
| PWRGD Output Current Sink Capability | IPWRGD | 1.2 | 6 | mA | VPWRGD = 0.200V | 8 | |
| Shutdown Input Logic High | VSHDN-HIGH | 45 | %VIN | VIN = 2.1V to 6.0V | 9 | ||
| Shutdown Input Logic Low | VSHDN-LOW | 15 | %VIN | VIN = 2.1V to 6.0V | 9 | ||
| SHDN Input Leakage Current | SHDNILK | -0.1 | 0.001 | 0.1 | µA | VIN = 6V, SHDN =VIN, SHDN = GND | 9 |
| PWRGD Leakage | PWRGD_LK | 1 | nA | VPWRGD = VIN = 6.0V | 8 | ||
| PWRGD Time Delay | TPG | 110 | µs | Rising Edge, RPULLUP = 10 kΩ | 8 | ||
| Detect Threshold to PWRGD Active Time Delay | TVDET-PWRGD | 200 | µs | VOUT = VPWRGD_TH + 50 mV to VPWRGD_TH - 50 mV | 9 | ||
| Output Delay From SHDN | TOR | 100 | µs | SHDN = GND to VIN, VOUT = GND to 95% VR | 9 | ||
| Output Noise | eN | 2 | µV/√Hz | IOUT = 200 mA, f = 1 kHz, COUT = 10 µF (X7R Ceramic), VOUT = 2.5V | 9 | ||
| Power Supply Ripple Rejection Ratio | PSRR | 55 | dB | f = 100 Hz, IOUT = 10 mA, VINAC = 200 mV pk-pk, CIN = 0 µF | 9 | ||
| Thermal Shutdown Temperature | TSD | 150 | °C | IOUT = 100 µA, VOUT = 1.8V, VIN = 2.8V | 9 | ||
| Thermal Shutdown Hysteresis | ΔTSD | 10 | °C | IOUT = 100 µA, VOUT = 1.8V, VIN = 2.8V | 9 | ||
| Operating Junction Temperature Range | TJ | -40 | 125 | °C | Steady State | 10 | |
| Maximum Junction Temperature | TJ | 150 | °C | Transient | 10 | ||
| Storage Temperature Range | TA | -65 | 150 | °C | 10 | ||
| Thermal Resistance, 5LD SOT-23, junction to ambient | θJA | 256 | °C/W | EIA/JEDEC JESD51-751-7, 4 Layer Board | 10 | ||
| Thermal Resistance, 5LD SOT-23, junction to case | θJC | 81 | °C/W | EIA/JEDEC JESD51-751-7, 4 Layer Board | 10 |
CAD (KiCad official)
- Symbol:
MCP1824T-1802E - Footprint:
Package_TO_SOT_SMD:SOT-23-5 - 3D model: SOT-23-5 (KiCad packages3D, STEP)
- 3D model files:
mcp1824t-1802e-etched.step/mcp1824t-1802e-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mcp1824t-1802e.step/mcp1824t-1802e.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (34 pp, sha256
dda3986a6bed8be8, retrieved 2026-10-26, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).