3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMCP4561-104E
Microchip Tech · Digital Potentiometers · MSOP-8
MCP4561-104E from Microchip Tech, in a MSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | HVC/A0 | input | High Voltage Command / Address 0: the A0 address bit is latched at POR/BOR, and the voltage on this pin selects a High Voltage command when HVC/A0 = VIHH. |
| 2 | SCL | input | I2C serial clock input; the device is a slave and accepts only external clock signals. |
| 3 | SDA | bidirectional | I2C serial data I/O; an open-drain N-channel driver. |
| 4 | VSS | power_in | Device ground reference (ground). |
| 5 | P0A | passive | Potentiometer 0 Terminal A, fixed connection to the Full-Scale wiper value (0x100 for 8-bit or 0x80 for 7-bit devices); voltage must be between VSS and VDD. |
| 6 | P0W | passive | Potentiometer 0 wiper terminal, the adjustable terminal of the digital potentiometer; voltage must be between VSS and VDD, and it supports both positive and negative current. |
| 7 | P0B | passive | Potentiometer 0 Terminal B, fixed connection to the Zero Scale wiper value (0x00); voltage must be between VSS and VDD, and it supports both positive and negative current. |
| 8 | VDD | power_in | Positive power supply input, relative to VSS; performance may not meet the data sheet specifications while VDD is below Vmin (2.7V). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | MSOP-8 |
| Category | Data Converters |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Resistance RAB | RAB | 80 | 100 | 120 | k | -104 devices (Note 1) | 5 |
| Resistance tolerance | RAB | -20 | 20 | % | -104 device, printed ±20% | 5 | |
| Supply voltage VDD | VDD | 2.7 | 5.5 | V | Device characteristics specified | 4 | |
| Supply voltage VDD (serial interface only) | VDD | 1.8 | 2.7 | V | Serial interface only | 4 | |
| HVC pin voltage range | VHV | 12.5 | V | VDD ≥ 4.5V | 4 | ||
| VDD start voltage to ensure wiper reset | VBOR | 1.65 | V | RAM retention voltage (VRAM) < VBOR | 4 | ||
| Supply current, serial interface active, 3.4 MHz | IDD | 600 | µA | Serial Interface Active, HVC/A0 = VIH (or VIL), Write all 0's to Volatile Wiper 0, VDD = 5.5V, FSCL = 3.4 MHz | 4 | ||
| Supply current, serial interface active, 100 kHz | IDD | 250 | µA | Serial Interface Active, HVC/A0 = VIH (or VIL), Write all 0's to Volatile Wiper 0, VDD = 5.5V, FSCL = 100 kHz | 4 | ||
| EE write current | IDD | 575 | µA | EE Write Current (Write Cycle) (Nonvolatile device only), VDD = 5.5V, FSCL = 400 kHz, Write all 0's to Nonvolatile Wiper 0, SCL = VIL or VIH | 4 | ||
| Serial interface inactive current | Istandby | 2.5 | 5 | µA | Serial Interface Inactive (Stop condition, SCL = SDA = VIH), Wiper = 0, VDD = 5.5V, HVC/A0 = VIH | 4 | |
| Wiper resistance RW | RW | 75 | 160 | Ω | VDD = 5.5 V, IW = 2.0 mA, code = 00h | 5 | |
| Wiper resistance RW | RW | 75 | 300 | Ω | VDD = 2.7 V, IW = 2.0 mA, code = 00h | 5 | |
| Full-scale error (8-bit, 100 k) | VWFSE | -0.5 | -0.1 | LSb | 100 k 8-bit 3.0V ≤ VDD ≤ 5.5V | 7 | |
| Zero-scale error (8-bit, 100 k) | VWZSE | 0.1 | 0.5 | LSb | 100 k 8-bit 3.0V ≤ VDD ≤ 5.5V | 7 | |
| Potentiometer integral non-linearity (8-bit) | INL | -1 | 0.5 | 1 | LSb | 8-bit 3.0V ≤ VDD ≤ 5.5V, MCP4XX1 devices only (Note 2) | 7 |
| Potentiometer differential non-linearity (8-bit) | DNL | -0.5 | 0.25 | 0.5 | LSb | 8-bit 3.0V ≤ VDD ≤ 5.5V, MCP4XX1 devices only (Note 2) | 7 |
| Maximum current through terminal A, W or B (full scale) | IT | 2.5 | mA | Terminal A IAW, W = Full-Scale (FS) | 6 | ||
| Maximum current terminal A to B (RAB min 80000) | IAB | 0.069 | mA | IAB, VB = 0V, VA = 5.5V, RAB(MIN) = 80000 | 6 | ||
| Pull-up current, internal VDD | IPU | 1.75 | mA | Internal VDD pull-up, VIHH pull-down, VDD = 5.5V, VIHH = 12.5V | 12 | ||
| Output low voltage (SDA) | VOL | 0.4 | V | VDD ≥ 2.0V, IOL = 3 mA | 12 | ||
| High-voltage input entry voltage | VIHHEN | 8.5 | 12.5 | V | Threshold for WiperLock Technology | 11 | |
| High-voltage limit | VMAX | 12.5 | V | Pin can tolerate VMAX or less. | 11 | ||
| Input leakage current | IIL | -1 | 1 | µA | VIN = VDD and VIN = VSS | 12 | |
| EEPROM programming write cycle time | tWC | 5 | 10 | ms | 12 | ||
| I2C clock frequency, standard mode | FSCL | 0 | 100 | kHz | Cb = 400 pF, 1.8V - 5.5V | 13 | |
| I2C clock frequency, fast mode | FSCL | 0 | 400 | kHz | Cb = 400 pF, 2.7V - 5.5V | 13 | |
| I2C clock frequency, high-speed 1.7 | FSCL | 0 | 1.7 | MHz | Cb = 400 pF, 4.5V - 5.5V | 13 | |
| I2C clock frequency, high-speed 3.4 | FSCL | 0 | 3.4 | MHz | Cb = 100 pF, 4.5V - 5.5V | 13 | |
| Voltage on VDD with respect to VSS | VDD | -0.6 | 7 | V | With respect to VSS | 3 | |
| Voltage on HVC/A0, A1, A2, SCL, SDA and WP | -0.6 | 12.5 | V | With respect to VSS | 3 | ||
| Input clamp current | IIK | -20 | 20 | mA | VI < 0, VI > VDD, VI > VPP ON HV pins | 3 | |
| Output clamp current | IOK | -20 | 20 | mA | VO < 0 or VO > VDD | 3 | |
| Maximum output current sunk by any output pin | 25 | mA | 3 | ||||
| Maximum output current sourced by any output pin | 25 | mA | 3 | ||||
| Maximum current out of VSS pin | 100 | mA | 3 | ||||
| Maximum current into VDD pin | 100 | mA | 3 | ||||
| Maximum current into PxA, PxW and PxB pins | -2.5 | 2.5 | mA | 3 | |||
| Storage temperature | -65 | 150 | °C | 3 | |||
| Ambient temperature with power applied | -40 | 125 | °C | 3 | |||
| Maximum junction temperature | TJ | 150 | °C | 3 | |||
| Soldering temperature of leads (10 seconds) | 300 | °C | 10 seconds | 3 | |||
| ESD protection (HBM) | 4 | kV | HBM | 3 | |||
| ESD protection (MM) | 300 | V | MM | 3 | |||
| Specified and operating temperature range | TA | -40 | 125 | °C | Extended temperature range | 17 | |
| Thermal resistance, 8L-MSOP | θJA | 211 | °C/W | 17 | |||
| Nominal resistance tempco | RAB/T | 150 | ppm/°C | TA = -40°C to +125°C | 5 | ||
| Ratiometric tempco | VWB/T | 15 | ppm/°C | Code = Mid-scale (80h or 40h) | 5 | ||
| Leakage current into A, W or B | IWL | 100 | nA | MCP4XX1 PxA = PxW = PxB = VSS | 6 | ||
| Bandwidth -3 dB (100 k, 8-bit) | BW | 100 | kHz | 100 k 8-bit Code = 80h, load = 30 pF | 8 | ||
| Pull-up current, HVC pin | IPU | 170 | µA | HVC pin, VDD = 5.5V, VHVC = 3V | 12 | ||
| HVC pull-up/pull-down resistance | RHVC | 16 | k | VDD = 5.5V, VHVC = 3V | 12 | ||
| Pin capacitance | CIN, COUT | 10 | pF | fC = 3.4 MHz | 12 |
CAD (KiCad official)
- Symbol:
MCP4561-104E - Footprint:
Package_SO:MSOP-8_3x3mm_P0.65mm - 3D model: MSOP-8 (KiCad packages3D, STEP)
- 3D model files:
mcp4561-104e-etched.step/mcp4561-104e-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mcp4561-104e.step/mcp4561-104e.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (102 pp, sha256
ad484e84f5bc6a00, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).