3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownTAS5508CPAGR
Texas Instruments · Audio Interface ICs · TQFP-64(10x10)
TAS5508CPAGR from Texas Instruments, in a TQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VRA_PLL | power_out | Internally regulated 1.8-V PLL analog supply reference; a low-ESR capacitor to AVSS_PLL is required and it must not be used to power external devices. |
| 2 | PLL_FLT_RET | passive | PLL external filter return, connected through an RC network to the PLL filter inputs. |
| 3 | PLL_FLTM | passive | PLL negative input, connected to the PLL filter return via an RC network. |
| 4 | PLL_FLTP | passive | PLL positive input, connected to the PLL filter return via an RC network. |
| 5 | AVSS | power_in | Analog ground. |
| 6 | AVSS | power_in | Analog ground. |
| 7 | VRD_PLL | power_out | Internally regulated 1.8-V PLL digital supply reference; a low-ESR capacitor to AVSS_PLL is required and it must not be used to power external devices. |
| 8 | AVSS_PLL | power_in | Analog ground for the PLL, which should reference the same ground as DVSS with ground noise minimized for low PLL jitter. |
| 9 | AVDD_PLL | power_in | 3.3-V analog power supply for the PLL, to be bypassed to AVSS_PLL with a low-ESR capacitor for low PLL jitter. |
| 10 | VBGAP | power_out | Band-gap voltage reference (internally regulated 1.2 V) with a typical 1-nF low-ESR capacitor to AVSS_PLL; it must not be used to power external devices. |
| 11 | RESET | input | Active-low system reset input with pull-up and 5-V tolerance; a logic low asynchronously restores default conditions, sets VALID low and places the PWM in hard mute. |
| 12 | HP_SEL | input | Headphone/speaker selector input with pull-up and 5-V tolerance; logic low selects the headphone (speakers off) and logic high selects the speakers (headphone off). |
| 13 | PDN | input | Active-low power-down input with pull-up and 5-V tolerance; a logic low powers down all logic and stops all clocks, with a 100-ms recovery time. |
| 14 | MUTE | input | Active-low soft mute input of the outputs with pull-up and 5-V tolerance; logic low mutes the outputs with a noiseless volume ramp. |
| 15 | DVDD | power_in | 3.3-V digital power supply. |
| 16 | DVSS | power_in | Digital ground. |
| 17 | VR_DPLL | power_out | Internally regulated 1.8-V digital PLL supply reference; a low-ESR capacitor to ground is required and it must not be used to power external devices. |
| 18 | OSC_CAP | passive | Oscillator capacitor connection for the crystal oscillator circuit. |
| 19 | XTL_OUT | output | 1.8-V output drive to the external 13.5-MHz fundamental-mode crystal (HCM49 recommended). |
| 20 | XTL_IN | input | 1.8-V oscillator input port for the external 13.5-MHz fundamental-mode crystal (HCM49 recommended); XTL_IN and XTL_OUT are the only LVCMOS terminals on the device. |
| 21 | RESERVED | passive | Reserved terminal; connect to digital ground. |
| 22 | RESERVED | passive | Reserved terminal; connect to digital ground. |
| 23 | RESERVED | passive | Reserved terminal; connect to digital ground. |
| 24 | SDA | bidirectional | I2C serial-control data input/output with 5-V tolerance. |
| 25 | SCL | bidirectional | I2C serial-control clock input/output with 5-V tolerance. |
| 26 | LRCLK | input | Serial-audio left/right clock (sampling-rate clock) input with 5-V tolerance. |
| 27 | SCLK | input | Serial-audio data shift clock input with 5-V tolerance. |
| 28 | SDIN4 | input | Serial-audio data input 4 with pull-down and 5-V tolerance; supports four stereo data formats at up to 64 Fs. |
| 29 | SDIN3 | input | Serial-audio data input 3 with pull-down and 5-V tolerance; supports four stereo data formats at up to 64 Fs. |
| 30 | SDIN2 | input | Serial-audio data input 2 with pull-down and 5-V tolerance; supports four stereo data formats at up to 64 Fs. |
| 31 | SDIN1 | input | Serial-audio data input 1 with pull-down and 5-V tolerance; supports four stereo data formats at up to 64 Fs. |
| 32 | PSVC | output | Power-supply volume control PWM output. |
| 33 | VR_DIG | power_out | Internally regulated 1.8-V digital core supply reference; a 4.7-mF low-ESR capacitor to DVSS is specified and it must not be used to power external devices. |
| 34 | DVSS | power_in | Digital ground. |
| 35 | DVSS | power_in | Digital ground. |
| 36 | DVDD | power_in | 3.3-V digital power supply. |
| 37 | BKND_ERR | input | Active-low back-end error input with pull-up; a logic low for at least 5 MCLK cycles places the PWM outputs in the hard-mute (M) state without changing system parameters. |
| 38 | DVSS | power_in | Digital ground. |
| 39 | VALID | output | Active-high output indicating the validity of the PWM outputs. |
| 40 | PWM_M_1 | output | PWM 1 output (differential negative). |
| 41 | PWM_P_1 | output | PWM 1 output (differential positive). |
| 42 | PWM_M_2 | output | PWM 2 output (differential negative). |
| 43 | PWM_P_2 | output | PWM 2 output (differential positive). |
| 44 | PWM_M_3 | output | PWM 3 output (differential negative). |
| 45 | PWM_P_3 | output | PWM 3 output (differential positive). |
| 46 | PWM_M_4 | output | PWM 4 output (differential negative). |
| 47 | PWM_P_4 | output | PWM 4 output (differential positive). |
| 48 | VR_PWM | power_out | Internally regulated 1.8-V PWM digital core supply reference; a low-ESR capacitor to DVSS_PWM is required and it must not be used to power external devices. |
| 49 | PWM_M_7 | output | PWM 7 (lineout L) output (differential negative). |
| 50 | PWM_P_7 | output | PWM 7 (lineout L) output (differential positive). |
| 51 | PWM_M_8 | output | PWM 8 (lineout R) output (differential negative). |
| 52 | PWM_P_8 | output | PWM 8 (lineout R) output (differential positive). |
| 53 | DVSS_PWM | power_in | Digital ground for the PWM section. |
| 54 | DVDD_PWM | power_in | 3.3-V digital power supply for the PWM section. |
| 55 | PWM_M_5 | output | PWM 5 output (differential negative). |
| 56 | PWM_P_5 | output | PWM 5 output (differential positive). |
| 57 | PWM_M_6 | output | PWM 6 output (differential negative). |
| 58 | PWM_P_6 | output | PWM 6 output (differential positive). |
| 59 | PWM_HPML | output | PWM left-channel headphone output (differential negative). |
| 60 | PWM_HPPL | output | PWM left-channel headphone output (differential positive). |
| 61 | PWM_HPMR | output | PWM right-channel headphone output (differential negative). |
| 62 | PWM_HPPR | output | PWM right-channel headphone output (differential positive). |
| 63 | MCLK | input | 3.3-V master clock input with pull-down and 5-V tolerance; the input frequency can range from 4 MHz to 50 MHz. |
| 64 | RESERVED | passive | Reserved terminal; connect to digital ground. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TQFP-64(10x10) |
| Category | Interface |
| Pins | 64 |
CAD (KiCad official)
- Symbol:
TAS5508CPAGR - Footprint:
Package_QFP:TQFP-64_10x10mm_P0.5mm - 3D model: TQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
tas5508cpagr-etched.step/tas5508cpagr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tas5508cpagr.step/tas5508cpagr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (110 pp, sha256
28c65c2b268608ad, retrieved 2026-10-11, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).