component
F280048PMQR
Public Made by Adomby adom
Texas Instruments Microcontrollers (MCU/MPU/SOC), LQFP-64(10x10). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownF280048PMQR
Texas Instruments · Microcontrollers (MCU/MPU/SOC) · LQFP-64(10x10)
F280048PMQR from Texas Instruments, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GPIO29 | bidirectional | General-purpose I/O 29 with multiplexed SCI-A TX, ePWM7_B, LIN-A RX, SPI-B STE and ERRORSTS functions. |
| 2 | GPIO28 | bidirectional | General-purpose I/O 28 with multiplexed SCI-A RX, ePWM7_A, LIN-A TX, SPI-B CLK and ERRORSTS functions. |
| 3 | XRSn | bidirectional | Device reset input and watchdog reset output, open-drain with internal pull-up; connect a 2.2 kΩ to 10 kΩ resistor to VDDIO. |
| 4 | VDD | power_in | 1.2 V digital logic supply pin; place a decoupling capacitor of about 20 µF total near the VDD pins. |
| 5 | VSS | power_in | Digital ground pin, must be connected to the board ground. |
| 6 | A6/PGA5_OF | passive | ADC-A analog input 6, also PGA-5 output filter pin. |
| 7 | B2/C6/PGA3_OF | passive | ADC-B analog input 2 and ADC-C input 6, also PGA-3 output filter pin. |
| 8 | B3/VDAC | passive | ADC-B analog input 3 and optional external reference for the on-chip DAC, with a fixed 100 pF capacitor to VSSA. |
| 9 | A2/B6/PGA1_OF | passive | ADC-A analog input 2, ADC-B input 6, and PGA-1 output filter pin. |
| 10 | PGA1_GND,PGA3_GND,PGA5_GND | power_in | PGA ground Kelvin reference pins for PGA-1, PGA-3 and PGA-5, tied to VSSA. |
| 11 | C4/PGA5_IN | passive | ADC-C analog input 4 and PGA-5 input. |
| 12 | C0/PGA1_IN | passive | ADC-C analog input 0 and PGA-1 input. |
| 13 | C2/PGA3_IN | passive | ADC-C analog input 2 and PGA-3 input. |
| 14 | A1/DACB_OUT | passive | ADC-A analog input 1 and buffered DAC-B output. |
| 15 | A0/B15/C15/DACA_OUT | passive | ADC-A analog input 0, ADC-B input 15, ADC-C input 15, and buffered DAC-A output. |
| 16 | VREFHIA,VREFHIB,VREFHIC | bidirectional | ADC high reference voltage; externally driven in external reference mode, device-driven in internal mode, with at least 2.2 µF to the matching VREFLO pin. |
| 17 | VREFLOA,VREFLOB,VREFLOC | input | ADC low reference voltage, connected to VSSA. |
| 18 | C1/PGA2_IN | passive | ADC-C analog input 1 and PGA-2 input. |
| 19 | C3/PGA4_IN | passive | ADC-C analog input 3 and PGA-4 input. |
| 20 | PGA2_GND,PGA4_GND,PGA6_GND | power_in | PGA ground Kelvin reference pins for PGA-2, PGA-4 and PGA-6, tied to VSSA. |
| 21 | VSSA | power_in | Analog ground pin. |
| 22 | VDDA | power_in | 3.3 V analog supply pin; place a decoupling capacitor of at least 2.2 µF to VSSA. |
| 23 | A4/B8/PGA2_OF | passive | ADC-A analog input 4, ADC-B input 8, and PGA-2 output filter pin. |
| 24 | B4/C8/PGA4_OF | passive | ADC-B analog input 4, ADC-C input 8, and PGA-4 output filter pin. |
| 25 | A10/B1/C10/PGA7_OF | passive | ADC-A input 10, ADC-B input 1, ADC-C input 10, and PGA-7 output filter pin. |
| 26 | VSS | power_in | Digital ground pin, must be connected to the board ground. |
| 27 | VDD | power_in | 1.2 V digital logic supply pin; requires decoupling capacitors on each VDD pin. |
| 28 | VDDIO | power_in | 3.3 V digital I/O supply pin; place at least 0.1 µF decoupling capacitor on each VDDIO pin. |
| 29 | FLT2 | unconnected | Flash test pin 2 reserved by TI; must be left unconnected. |
| 30 | FLT1 | unconnected | Flash test pin 1 reserved by TI; must be left unconnected. |
| 31 | GPIO11 | bidirectional | General-purpose I/O 11 with multiplexed ePWM6_B, SCI-B RX, EQEP1_B, SPI-A STE and FSI RX functions. |
| 32 | GPIO33 | bidirectional | General-purpose I/O 33 with multiplexed I2C-A SCL, SPI-B STE, LIN-A RX, CAN-A RX and FSI RX clock functions. |
| 33 | GPIO16 | bidirectional | General-purpose I/O 16 with multiplexed SPI-A SIMO, CAN-B TX, ePWM5_A, SCI-A TX and XCLKOUT functions. |
| 34 | GPIO17 | bidirectional | General-purpose I/O 17 with multiplexed SPI-A SOMI, CAN-B RX, ePWM5_B, SCI-A RX and SDFM-1 clock functions. |
| 35 | GPIO24 | bidirectional | General-purpose I/O 24 with multiplexed OUTPUTXBAR1, EQEP2_A, ePWM8_A, SPI-B SIMO and ERRORSTS functions. |
| 36 | TCK | input | JTAG test clock input with internal pull-up. |
| 37 | GPIO37/TDO | tri_state | General-purpose I/O 37, default function JTAG TDO, tri-stated when JTAG is inactive; enable pull-up or external pull-up to avoid a floating input. |
| 38 | TMS | bidirectional | JTAG test mode select input with internal pull-up; add an external 2.2 kΩ pull-up to VDDIO. |
| 39 | GPIO35/TDI | input | General-purpose I/O 35, default function JTAG TDI input; enable internal pull-up or add an external pull-up to avoid a floating input. |
| 40 | GPIO32 | bidirectional | General-purpose I/O 32 with multiplexed I2C-A SDA, SPI-B CLK, ePWM8_B, LIN-A TX and CAN-A TX functions. |
| 41 | GPIO18_X2 | bidirectional | General-purpose I/O 18, also crystal oscillator output X2; usable as GPIO only when the system is clocked from INTOSC and X1 has an external pull-down of about 1 kΩ. |
| 42 | X1 | input | Crystal oscillator input or single-ended 3.3 V clock input; must be configured by software before enabling the crystal oscillator. |
| 43 | VDDIO | power_in | 3.3 V digital I/O supply pin; place at least 0.1 µF decoupling capacitor on each VDDIO pin. |
| 44 | VDD | power_in | 1.2 V digital logic supply pin; requires decoupling capacitors on each VDD pin. |
| 45 | VSS | power_in | Digital ground pin, must be connected to the board ground. |
| 46 | VREGENZ | input | Internal regulator enable with internal pull-down; connect to VSS to enable the internal VREG, or to VDDIO to use an external VDD supply. |
| 47 | GPIO8 | bidirectional | General-purpose I/O 8 with multiplexed ePWM5_A, CAN-B TX, ADCSOCAO, SCI-A TX, SPI-A SIMO and I2C-A SCL functions. |
| 48 | GPIO4 | bidirectional | General-purpose I/O 4 with multiplexed ePWM3_A, OUTPUTXBAR3, CAN-A TX and FSI RX clock functions. |
| 49 | GPIO3 | bidirectional | General-purpose I/O 3 with multiplexed ePWM2_B, OUTPUTXBAR2, PMBus-A SCL, SPI-A CLK, SCI-A RX and FSI RX functions. |
| 50 | GPIO2 | bidirectional | General-purpose I/O 2 with multiplexed ePWM2_A, OUTPUTXBAR1, PMBus-A SDA, SCI-A TX and FSI RX functions. |
| 51 | GPIO1 | bidirectional | General-purpose I/O 1 with multiplexed ePWM1_B and I2C-A SCL functions. |
| 52 | GPIO0 | bidirectional | General-purpose I/O 0 with multiplexed ePWM1_A and I2C-A SDA functions. |
| 53 | VDDIO_SW | power_in | 3.3 V supply for the internal DC-DC regulator; requires a 20 µF bulk input capacitor and must be tied to VDDIO. |
| 54 | GPIO23_VSW | bidirectional | General-purpose I/O 23, default DC-DC switch output VSW when the internal regulator is enabled; about 100 pF internal capacitance. |
| 55 | VSS_SW | power_in | Internal DC-DC regulator ground; must be tied to VSS. |
| 56 | GPIO22_VFBSW | bidirectional | General-purpose I/O 22, default DC-DC feedback VFBSW when the internal regulator is enabled; connect to the node where L(VSW) meets VDD. |
| 57 | GPIO7 | bidirectional | General-purpose I/O 7 with multiplexed ePWM4_B, OUTPUTXBAR5, EQEP1_B, CAN-B RX, SPI-B SIMO and FSI TX clock functions. |
| 58 | VSS | power_in | Digital ground pin, must be connected to the board ground. |
| 59 | VDD | power_in | 1.2 V digital logic supply pin; requires decoupling capacitors on each VDD pin. |
| 60 | VDDIO | power_in | 3.3 V digital I/O supply pin; place at least 0.1 µF decoupling capacitor on each VDDIO pin. |
| 61 | GPIO5 | bidirectional | General-purpose I/O 5 with multiplexed ePWM3_B, OUTPUTXBAR3, CAN-A RX, SPI-A STE and FSI TX functions. |
| 62 | GPIO9 | bidirectional | General-purpose I/O 9 with multiplexed ePWM5_B, SCI-B TX, OUTPUTXBAR6, EQEP1_INDEX, SCI-A RX and SPI-A CLK functions. |
| 63 | GPIO10 | bidirectional | General-purpose I/O 10 with multiplexed ePWM6_A, CAN-B RX, ADCSOCBO, EQEP1_A, SCI-B TX, SPI-A SOMI and I2C-A SDA functions. |
| 64 | GPIO6 | bidirectional | General-purpose I/O 6 with multiplexed ePWM4_A, OUTPUTXBAR4, SYNCOUT, EQEP1_A, CAN-B TX and SPI-B SOMI functions. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | LQFP-64(10x10) |
| Category | Embedded Processors & Controllers |
| Pins | 64 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage VDDIO referenced to VSS | VDDIO | -0.3 | 4.6 | V | 58 | ||
| Supply voltage VDDA referenced to VSSA | VDDA | -0.3 | 4.6 | V | 58 | ||
| Supply voltage VDD referenced to VSS | VDD | -0.3 | 1.5 | V | 58 | ||
| Voltage difference between VDDIO and VDDIO_SW pins | -0.3 | 0.3 | V | 58 | |||
| Input voltage (3.3V) | VIN | -0.3 | 4.6 | V | 58 | ||
| Output voltage | VO | -0.3 | 4.6 | V | 58 | ||
| Digital input clamp current per pin | IIK | -20 | 20 | mA | VIN < VSS or VIN > VDDIO | 58 | |
| Analog input clamp current per pin | IIKANALOG | -20 | 20 | mA | VIN < VSSA or VIN > VDDA | 58 | |
| Total input clamp current, all inputs | IIKTOTAL | -20 | 20 | mA | VIN < VSS/VSSA or VIN > VDDIO/VDDA | 58 | |
| Digital output current per pin | IOUT | -20 | 20 | mA | 58 | ||
| Natural ventilation temperature | TA | -40 | 125 | °C | Natural ventilation | 58 | |
| Operating junction temperature | TJ | -40 | 150 | °C | 58 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 58 | ||
| Device supply voltage VDDIO and VDDA | VDDIO, VDDA | 3.3 | 3.63 | V | Internal BOR enabled | 59 | |
| Device supply voltage VDDIO and VDDA | VDDIO, VDDA | 2.8 | 3.3 | 3.63 | V | Internal BOR disabled | 59 |
| Device supply voltage VDD | VDD | 1.14 | 1.2 | 1.32 | V | 59 | |
| Natural ventilation temperature, Q version (AEC Q100 qualified) | TA | -40 | 125 | °C | Q version (AEC Q100 qualified) | 59 | |
| Buffered DAC output voltage range | VOUT | 0.3 | V | RL = 5kΩ | 136 | ||
| Buffered DAC output voltage range | VOUT | 0.6 | V | RL = 1kΩ | 136 | ||
| Low-level output voltage VOL | VOL | 0.4 | V | IOL=IOL MAX | 67 | ||
| Low-level output voltage VOL | VOL | 0.2 | V | IOL = 100µA | 67 | ||
| High-level input voltage (3.3V) | VIH | 2 | V | (3.3V) | 67 | ||
| Low-level input voltage (3.3V) | VIL | 0.8 | V | (3.3V) | 67 | ||
| Internal regulator output | VVREG | 1.14 | 1.2 | 1.32 | V | 80 | |
| Crystal load capacitance | CL1, CL2 | 12 | 24 | pF | 93 | ||
| Crystal shunt capacitance | C0 | 7 | pF | 93 | |||
| INTOSC1 and INTOSC2 frequency | fINTOSC | 9.7 | 10 | 10.3 | MHz | 94 | |
| Internal oscillator frequency stability | -3 | 3 | % | 95 | |||
| ADC clock frequency ADCCLK | ADCCLK | 5 | 50 | MHz | 123 | ||
| ADC offset error | -5 | 2 | 5 | LSB | 124 | ||
| ADC gain error, external reference | -5 | 3 | 5 | LSB | External reference | 124 | |
| ADC integral nonlinearity INL | INL | -2 | 1 | 2 | LSB | 124 | |
| ADC differential nonlinearity DNL | DNL | -1 | 0.5 | 1 | LSB | 124 | |
| Buffered DAC load regulation | -1 | 1 | mV/V | 136 | |||
| Buffered DAC offset error | -10 | 10 | mV | Midpoint | 136 | ||
| Buffered DAC gain error | -2.5 | 2.5 | FSR 百分比 | 136 | |||
| Buffered DAC differential nonlinearity DNL | DNL | -1 | 0.4 | 1 | LSB | Corrected endpoints | 136 |
| Buffered DAC integral nonlinearity INL | INL | -5 | 2 | 5 | LSB | Corrected endpoints | 136 |
| PMBus low-level input voltage VIL | VIL | 0.8 | V | 176 | |||
| PMBus high-level input voltage VIH | VIH | 2.1 | V | 176 | |||
| PMBus low-level output voltage VOL | VOL | 0.4 | V | Ipullup = 4mA | 176 | ||
| PMBus SCL clock frequency, fast mode | fSCL | 10 | 400 | kHz | Fast mode | 176 | |
| PMBus SCL clock frequency, standard mode | fSCL | 10 | 100 | kHz | Standard mode | 177 |
CAD (KiCad official)
- Symbol:
F280048PMQR - Footprint:
Package_QFP:LQFP-64_10x10mm_P0.5mm - 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
f280048pmqr-etched.step/f280048pmqr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);f280048pmqr.step/f280048pmqr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (277 pp, sha256
867e7bb5ada6819c, retrieved 2026-11-05, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).