3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownIS31FL3739-GRLS4-TR
ISSI(Integrated Silicon Solution) · LED Drivers · SOP-24-300mil
IS31FL3739-GRLS4-TR from ISSI(Integrated Silicon Solution), in a SOP-24-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW2 | output | Switch power source for matrix row 2 (scanned high-side switch, active high when LED on). |
| 2 | SW1 | output | Switch power source for matrix row 1 (scanned high-side switch, active high when LED on). |
| 3 | VCC | power_in | Power supply, 2.7V to 5.5V (absolute max 6.0V), decoupled with capacitors close to the pin. |
| 4 | GND | power_in | Ground. |
| 5 | ISET | passive | Current setting pin; an external RISET resistor to ground (10kΩ typical) sets the CSx output current. |
| 6 | SDA | bidirectional | I2C serial data line, bidirectional open-drain requiring a pull-up resistor (also selectable as AD address connection). |
| 7 | SCL | input | I2C serial clock input, up to 1MHz. |
| 8 | SDB | input | Shutdown input; the chip shuts down when pulled low and a rising edge resets the I2C interface. |
| 9 | AD | input | I2C address setting; connect to GND, SCL, SDA or VCC to set address bits A2:A1. |
| 10 | CS1 | output | Current sink output 1, up to about 35mA with RISET=10kΩ. |
| 11 | CS2 | output | Current sink output 2, up to about 35mA with RISET=10kΩ. |
| 12 | CS3 | output | Current sink output 3, up to about 35mA with RISET=10kΩ. |
| 13 | CS4 | output | Current sink output 4, up to about 35mA with RISET=10kΩ. |
| 14 | CS5 | output | Current sink output 5, up to about 35mA with RISET=10kΩ. |
| 15 | GND | power_in | Ground. |
| 16 | CS6 | output | Current sink output 6, up to about 35mA with RISET=10kΩ. |
| 17 | CS7 | output | Current sink output 7, up to about 35mA with RISET=10kΩ. |
| 18 | SW9/CS8 | output | Switch power source SW9 (7×9 mode) or current sink output CS8 (8×n mode). |
| 19 | SW8 | output | Switch power source for matrix row 8. |
| 20 | SW7 | output | Switch power source for matrix row 7. |
| 21 | SW6 | output | Switch power source for matrix row 6. |
| 22 | SW5 | output | Switch power source for matrix row 5. |
| 23 | SW4 | output | Switch power source for matrix row 4. |
| 24 | SW3 | output | Switch power source for matrix row 3. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | ISSI(Integrated Silicon Solution) |
| Package | SOP-24-300mil |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 24 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | 2.7 | 5.5 | V | 5 | ||
| Quiescent power supply current | ICC | 2 | 3 | mA | VSDB= VCC, all LEDs off | 5 | |
| Shutdown current | ISD | 3 | 5 | µA | VSDB= 0V | 5 | |
| Shutdown current (software) | ISD | 3 | 5 | µA | SDB= VCC, Configuration Register written "0000 0000" | 5 | |
| Maximum constant current of CSx | IOUT | 31.5 | 35 | 38.5 | mA | RISET= 10kΩ, GCC= "100 0000", SL= 0xFF | 5 |
| Average current on each LED | ILED | 4.22 | mA | RISET= 10kΩ, GCC= "100 0000", SL= 0xFF, n= 8, Duty= 1/8.29 | 5 | ||
| Current switch headroom voltage SWx | VHR | 500 | 550 | mV | ISWITCH= 600mA RISET= 10kΩ, GCC= "100 0000", SL= 0xFF | 5 | |
| Current sink headroom voltage CSx | VHR | 400 | 500 | mV | ISINK= 34mA, RISET= 10kΩ, GCC= "100 0000", SL= 0xFF | 5 | |
| Period of scanning | tSCAN | 22 | 30 | 46 | µs | B2h= "0x01" (PWM frequency= 32kHz) | 5 |
| Non-overlap blanking time during scan | tNOL1 | 0.3 | 0.8 | 1.2 | µs | B2h= "0x01" (PWM frequency= 32kHz) | 5 |
| Delay total time for CS1 to CS8 | tNOL2 | 0.1 | 0.27 | 0.4 | µs | B2h= "0x01" (PWM frequency= 32kHz) | 5 |
| Logic 0 input voltage | VIL | 0.4 | V | VCC= 2.7V~5.5V, LGC= "0" | 5 | ||
| Logic 1 input voltage | VIH | 1.4 | V | VCC= 2.7V~5.5V, LGC= "0" | 5 | ||
| Logic 0 input voltage | VIL | 0.6 | V | VCC= 2.7V~5.5V, LGC= "1" | 5 | ||
| Logic 1 input voltage | VIH | 2.4 | V | VCC= 2.7V~5.5V, LGC= "1" | 5 | ||
| Input schmitt trigger hysteresis | VHYS | 0.2 | V | VCC= 3.6V, LGC= "0", LGC= "1" | 5 | ||
| Logic 0 input current | IIL | 5 | nA | SDB= L, VINPUT= L (Note 5) | 5 | ||
| Logic 1 input current | IIH | 5 | nA | SDB= L, VINPUT= H (Note 5) | 5 | ||
| Supply voltage | VCC | -0.3 | 6 | V | 5 | ||
| Voltage at any input pin | -0.3 | 6 | V | -0.3V ~ VCC+0.3V | 5 | ||
| Maximum junction temperature | TJMAX | 150 | °C | 5 | |||
| Storage temperature range | TSTG | -65 | 150 | °C | 5 | ||
| Operating temperature range | TA=TJ | -40 | 125 | °C | 5 | ||
| Package thermal resistance, junction to ambient | θJA | 41 | °C/W | 4 layer standard test PCB based on JESD 51-2A | 5 | ||
| ESD (HBM) | -8 | 8 | kV | 5 | |||
| ESD (CDM) | -750 | 750 | V | 5 | |||
| Serial-clock frequency (Fast Mode) | fSCL | 400 | kHz | Fast Mode | 6 | ||
| Serial-clock frequency (Fast Mode Plus) | fSCL | 1000 | kHz | Fast Mode Plus | 6 |
CAD (KiCad official)
- Symbol:
IS31FL3739-GRLS4-TR - Footprint:
Package_SO:SOP-24_7.5x15.4mm_P1.27mm - 3D model: SOP-24-300mil, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 2.65 mm nominal SOIC height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files:
is31fl3739-grls4-tr-etched.step/is31fl3739-grls4-tr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);is31fl3739-grls4-tr.step/is31fl3739-grls4-tr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: ISSI(Integrated Silicon Solution) datasheet (22 pp, sha256
c32010e928a5cb65, retrieved 2026-10-30, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).