Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

TPD3S716QDBQRQ1

Texas Instruments · Surge Suppressors · SSOP-16-150mil

TPD3S716QDBQRQ1 from Texas Instruments, in a SSOP-16-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 NC unconnected No connect; leave floating or connect to ground, and do not connect to VBUS_CON.
2 VBUS_CON output Connect to USB connector VBUS; provides IEC 61000-4-2 ESD protection, and the pin withstands −0.3 V to 18 V per the absolute maximum ratings.
3 VBUS_CON output Connect to USB connector VBUS; provides IEC 61000-4-2 ESD protection, and the pin withstands −0.3 V to 18 V per the absolute maximum ratings.
4 GND power_in Ground; connect to PCB ground plane.
5 VD- bidirectional Connect to USB connector D-; provides IEC 61000-4-2 ESD protection and is rated −0.3 V to 18 V per the absolute maximum ratings.
6 VD+ bidirectional Connect to USB connector D+; provides IEC 61000-4-2 ESD protection and is rated −0.3 V to 18 V per the absolute maximum ratings.
7 VEN input Active-low enable input; drive low to enable the VBUS path and high to disable it, with a recommended voltage range of 0 V to 5.9 V.
8 DEN input Active-low enable input; drive low to enable the data path and high to disable it, with a recommended voltage range of 0 V to 5.9 V.
9 VIN power_in Connect to 3.3-V I/O; controls the OVP threshold for VD+/VD-, with a recommended supply range of 3 V to 3.6 V.
10 FLT output Open-drain fault output that is pulled low when a fault occurs; absolute maximum −0.3 V to 7 V and VOL of 0.4 V max at 3 mA.
11 D+ bidirectional Connect to the internal transceiver D+ pin.
12 D- bidirectional Connect to the internal transceiver D- pin.
13 GND power_in Ground; connect to PCB ground plane.
14 VBUS_SYS input Connect to internal VBUS plane; recommended internal supply DC voltage is 4.75 V to 5.9 V.
15 VBUS_SYS input Connect to internal VBUS plane; recommended internal supply DC voltage is 4.75 V to 5.9 V.
16 IADJ input Connect to a resistor to GND to set the current limit threshold; RADJ is specified at a minimum of 57 kΩ.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package SSOP-16-150mil
Category TVS/Fuse/Board Level Protection
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VBUS_CON Supply voltage from USB connector -0.3 18 V 4
VBUS_SYS Internal Supply DC voltage Rail on the PCB -0.3 6 V 4
VD+, VD- Voltage range from connector-side USB data lines -0.3 18 V 4
D+, D- Voltage range for internal USB data lines -0.3 V max printed as VIN + 0.3 V 4
VIN Voltage range for VIN supply input -0.3 4 V 4
Voltage on enable pin DEN DEN 7 V 4
Voltage on enable pin VEN VEN 7 V 4
IBUS Maximum DC output current on VBUS_CON pin IBUS 2.4 A 4
Voltage range for IADJ pin VIADJ -0.3 V max printed as VVBUS_SYS + 0.3 V 4
Voltage range for the FLT pin VFLT -0.3 7 V 4
TA Operating free air temperature TA -40 125 °C 4
TSTG Storage temperature TSTG -65 150 °C 4
VBUS_CON Supply voltage from USB connector (recommended) 5.9 V 4
VBUS_SYS Internal supply DC voltage Rail on the PCB (recommended) 4.75 5.9 V 4
VD+, VD- Voltage range from connector-side USB data lines (recommended) 0 V max printed as VIN + 0.3 V 4
D+, D- Voltage range for internal USB data lines (recommended) 0 V max printed as VIN + 0.3 V 5
VIN Voltage range for VIN supply VIN 3 3.6 V 5
IBUS Current through VBUS switch IBUS 2.4 A 5
VEN, DEN Voltage range for enable VEN, DEN 0 5.9 V 5
CSYS Input capacitance VBUS_SYS pin CSYS 100 µF 5
CLOAD Output load capacitance VBUS_CON pin CLOAD 1 µF 5
CVIN VIN capacitance VIN pin CVIN 1 µF 5
RADJ Resistance of RADJ resistor IADJ pin RADJ 57 kΩ 5
VBUS sleep current consumption IVBUS_SLEEP 45 150 µA Measured at VBUS_SYS pin, VEN = 5 V, DEN = 5 V 5
VBUS operating current consumption IVBUS 285 380 µA Measured at VBUS_SYS pin 5
Leakage current for VIN IVIN 12 20 µA Measured at VIN pin, VIN = 3.6 V 5
Leakage into VBUS_SYS while shorted to battery and powered on ION(LEAK) 225 300 µA Measured flowing into VBUS_SYS pin, VBUS_SYS = 5 V, VBUS_CON = 18 V 5
Leakage out of data path while shorted to battery and unpowered ID(OFF_LEAK) -1 1 µA Measured flowing out of D+ or D- pins, VBUS_SYS = 0 V, VD+ or VD- = 18 V, VIN = 0 V, D+/D- = 0 V 5
Leakage out of data path while shorted to battery and powered on ID(ON_LEAK) -1 1 µA Measured flowing out of D+ or D- pins, VBUS_SYS = 5 V, VD+ or VD- = 18 V, VIN = 3.3 V, D+/D- = 0 V 5
Undervoltage lockout rising for VIN VUVLO(RISING) 2.6 2.7 2.9 V Ramp VIN up until VBUS and Data FETs turn on, VEN = 0 V, DEN = 0 V 6
Undervoltage lockout falling for VIN VUVLO(FALLING) 2.5 2.6 2.8 V Ramp VIN down until VBUS and Data FETs turn off, VEN = 0 V, DEN = 0 V 6
Overcurrent limit VBUS ILIM 505 620 mA RADJ = 280 kΩ ± 1%; progressively load VBUS_CON until device asserts FLT 6
Overcurrent limit VBUS ILIM 0.905 1.1 A RADJ = 158 kΩ ± 1%; progressively load VBUS_CON until device asserts FLT 6
Overcurrent limit VBUS ILIM 1.005 1.2 A RADJ = 143 kΩ ± 1%; progressively load VBUS_CON until device asserts FLT 6
Overcurrent limit VBUS ILIM 1.505 1.8 A RADJ = 93.1 kΩ ± 1%; progressively load VBUS_CON until device asserts FLT 6
Overcurrent limit VBUS ILIM 1.8 2.16 A RADJ = 76.8 kΩ ± 1%; progressively load VBUS_CON until device asserts FLT 6
Overcurrent limit VBUS ILIM 2.105 2.57 A RADJ = 66.5 kΩ ± 1%; progressively load VBUS_CON until device asserts FLT 6
Overcurrent limit VBUS ILIM 2.405 2.93 A RADJ = 57.6 kΩ ± 1%; progressively load VBUS_CON until device asserts FLT 6
Overcurrent limit VBUS ILIM 550 700 850 mA IADJ = GND; progressively load VBUS_CON until device asserts FLT 6
Overcurrent limit VBUS ILIM 1.1 1.4 1.7 A IADJ = VBUS_SYS; progressively load VBUS_CON until device asserts FLT 6
The rising over-temperature protection shutdown threshold TSD(RISING) 150 165 180 ℃ VBUS_SYS = 5 V, VEN = 0 V, DEN = 0 V, no load on VBUS_CON; TA stepped up until FLT asserted 6
The falling over-temperature protection shutdown threshold TSD(FALLING) 125 130 142 ℃ VBUS_SYS = 5 V, VEN = 0 V, DEN = 0 V, no load on VBUS_CON; TA stepped down until FLT deasserted 6
The over-temperature protection shutdown threshold hysteresis TSD(HYST) 10 35 55 ℃ TSD(RISING), TSD(FALLING) 6
Input overvoltage protection threshold VBUS_CON rising VOVP(RISING) 5.6 5.8 6 V Increase VBUS_CON from 5 V to 7 V; measure when FLT is asserted 6
Input overvoltage protection threshold VBUS_CON falling VOVP(FALLING) 5.52 5.75 5.98 V Decrease VBUS_CON from 7 V to 5 V; measure when FLT is deasserted 6
Reverse supply detection threshold rising VBUS_CON, VBUS_SYS VREV_SUPPLY(RISING) 140 200 260 mV VBUS_SYS = 5 V; increase VBUS_CON from VBUS_SYS to VBUS_SYS + 300 mV; 25°C ≤ TA ≤ 125°C 6
Reverse supply detection threshold falling VBUS_CON, VBUS_SYS VREV_SUPPLY(FALLING) 70 120 165 mV VBUS_SYS = 5 V; decrease VBUS_CON from VBUS_SYS + 300 mV to VBUS_SYS; 25°C ≤ TA ≤ 125°C 6
Undervoltage lockout rising for VBUS_SYS VUVLO(SYS_RISING) 3.1 3.3 3.6 V VBUS_SYS voltage rising from 0 V to 5 V 7
VBUS_SYS UVLO Hysteresis VHYS(UVLO_SYS) 50 75 100 mV Difference between rising and falling UVLO thresholds on VBUS_SYS 7
Undervoltage lockout falling for VBUS_SYS VUVLO(SYS_FALLING) 3 3.2 3.5 V VBUS_SYS voltage falling from 5 V to 2.9 V 7
Short-to-ground comparator rising threshold VBUS_CON VSHRT(RISING) 2.5 2.6 2.7 V Increase VBUS_CON from 0 V until device transitions from short-circuit to over-current mode 7
Short-to-ground comparator falling threshold VBUS_CON VSHRT(FALLING) 2.4 2.5 2.6 V VBUS_SYS = 5 V; VIN = 3.3 V; VEN = 0 V, DEN = 0 V; decrease VBUS_CON from 5 V until transition to short-circuit mode 7
Short-to-ground current source VBUS_CON ISHRT 150 350 mA Current sourced from VBUS_SYS when device is in short-circuit mode 7
On Resistance between D+ and VD+ or D- and VD- RON 4 6.5 Ω Measure between D+ and VD+ or D- and VD-, voltage between 0 V and 0.4 V 7
On Resistance flatness RON(Flat) 0.2 1 Ω Measure between D+ and VD+ or D- and VD-, sweep voltage between 0 V and 0.4 V 7
Output discharge resistance R(DISCHARGE) 18 30 kΩ VEN = 5 V, DEN = 5 V, VBUS_CON = 5 V; measure current flow to ground 7
VBUS path ON resistance RON 63 135 mΩ VBUS_CON = 5 V, IOUT = 1.5 A 7
OVP Response time VBUS tOVP_response 2 4 µs Measured from OVP condition to FET turnoff 8
Junction-to-ambient thermal resistance θJA 98.8 °C/W 5
Junction-to-ambient thermal resistance (custom layout) θJA(Custom) 57 °C/W See Layout Optimized for Thermal Performance section 5

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper signal pins when possible. Another key strategy is to maximize the copper weight of the PCB metal layers. This 24

CAD (KiCad official)

  • Symbol: TPD3S716QDBQRQ1
  • Footprint: Package_SO:SSOP-16_3.9x4.9mm_P0.635mm
  • 3D model: SSOP-16-150mil (KiCad packages3D, STEP)

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (33 pp, sha256 3c73efd1fb7bad2b, retrieved 2026-11-11, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF