component
SPL06-001
Public Made by Adomby adom
Goertek Pressure Sensors, LGA-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownSPL06-001
Goertek · Pressure Sensors · LGA-8
SPL06-001 from Goertek, in a LGA-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table and the footprint is an Adom_Gen land derived from the manufacturer drawing; the 3D model is generated to fit it.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Ground pin; connect to the system ground (Figure 8 to Figure 10 application circuits show GND tied to the system ground). |
| 2 | CSB | input | Chip select, active low, with an integrated pull-up; tie to GND for SPI 3-wire, SPI 4-wire and interrupt modes, and tie to VDDIO when I2C is used (not used in I2C). |
| 3 | SDA | bidirectional | Serial data line: data in/out for SPI 3-wire and I2C, and data in only for SPI 4-wire. |
| 4 | SCK | input | Serial clock input for the serial interface (labelled SCL in the I2C application circuit of Figure 8); SPI and I2C timing values are given in Tables 5 and 6, with a maximum I2C clock of 3.4 MHz and a maximum SPI clock of 10 MHz. |
| 5 | SDO | bidirectional | Function depends on interface mode: not used for SPI 3-wire, interrupt output for SPI 3-wire with interrupt, serial data out for SPI 4-wire, and least significant bit of the device address (0x76 when pulled to GND, 0x77 by default) for I2C, which can also carry the interrupt in I2C with interrupt. |
| 6 | VDDIO | power_in | Digital supply voltage for digital blocks and the I/O interface, 1.2 V to 3.6 V. |
| 7 | GND | power_in | Ground pin; connect to the system ground. |
| 8 | VDD | power_in | Supply voltage for analog blocks, 1.7 V to 3.6 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Goertek |
| Package | LGA-8 |
| Category | Sensors |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage temperature | -40 | 125 | °C | 6 | |||
| Supply Voltage | 4 | V | All pins | 6 | |||
| Voltage at all IO Pins | 4 | V | All pins | 6 | |||
| ESD rating | -2 | 2 | kV | JESD22-A114 | 6 | ||
| Overpressure | 10000 | hPa | 6 | ||||
| Operating temperature | TA | -40 | 25 | 85 | °C | Operational | 6 |
| Operating temperature (full accuracy) | TA | 0 | 25 | 65 | °C | Full accuracy | 6 |
| Operating Pressure | P | 300 | 1100 | hPa | 6 | ||
| Supply voltage | VDD | 1.7 | 3.6 | V | 6 | ||
| Interface supply voltage | VDDIO | 1.2 | 3.6 | V | 6 | ||
| Supply current, Low Power | Idd | 3 | 5 | uA | 1 Hz | 6 | |
| Supply current, Standard | Idd | 11 | 15 | uA | 1 Hz | 6 | |
| Supply current, High precision | Idd | 40 | 50 | uA | 1 Hz | 6 | |
| Peak current | Ipeak | 400 | 500 | uA | During conversion | 6 | |
| Standby current | Iddsbm | 1 | uA | 6 | |||
| Relative accuracy pressure | P_R | -6 | 6 | Pa | 950…1050hPa, +25…+40°C | 7 | |
| Relative accuracy pressure | P_R | -0.5 | 0.5 | m | 950…1050hPa, +25…+40°C | 7 | |
| Absolute accuracy pressure | P_A | -1 | 1 | hPa | 300...1100hPa, 0…+65℃ | 7 | |
| Noise in pressure, Low Power mode | P_Noise | 2 | 5 | PaRMS | Low Power mode | 7 | |
| Noise in pressure, Standard mode | P_Noise | 0.5 | 1.2 | PaRMS | Standard mode | 7 | |
| Noise in pressure, High precision mode | P_Noise | 0.3 | 0.6 | PaRMS | High precision mode | 7 | |
| Offset temperature coefficient (pressure) | TCO | -0.5 | 0.5 | Pa/K | 1000hPa, +25…+40°C | 7 | |
| Offset temperature coefficient (altitude) | TCO | -4.2 | 4.2 | cm/K | 1000hPa, +25…+40°C | 7 | |
| Absolute accuracy temperature | -3 | 1 | 3 | °C | 0…+65℃ | 7 | |
| Pressure/Temperature measurement rate | f | 1 | 128 | Hz | 7 | ||
| Pressure measurement time, Low Power mode | t | 5 | 8 | ms | Low Power mode | 7 | |
| Pressure measurement time, Standard mode | t | 28 | 35 | ms | Standard mode | 7 | |
| Pressure measurement time, High precision mode | t | 105 | 115 | ms | High precision mode | 7 | |
| Long term stability | -1 | 1 | hPa | 12 month | 7 | ||
| Supply voltage ramp-up time | tvddup | 0.001 | 5 | ms | Time for supply voltage to reach 90% of final value | 7 | |
| Serial data clock (I2C) | fI2C | 3.4 | MHz | For I2C | 7 | ||
| Serial data clock (SPI) | fSPI | 10 | MHz | For SPI | 7 | ||
| Time to sensor ready | TSensor_rdy | 12 | ms | SENSOR_RDY bit set when sensor is ready | 7 | ||
| Time to coefficients available | TCoef_rdy | 40 | ms | COEF_RDY bit set when coefficients can be read out | 7 |
CAD (Adom-generated)
- Symbol:
SPL06-001 - Footprint:
Adom_Gen:Goertek_SPL06_8b15d6 - 3D model: generated to fit the land (STEP)
- 3D model files:
spl06-001-etched.step/spl06-001-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);spl06-001.step/spl06-001.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Goertek datasheet (38 pp, sha256
2e502c4bb35ed3b8, retrieved 2026-11-10, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing. 3D model generated to fit that land.