LTC2965IMS#PBF from Analog Devices, in a MSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin	Name	Type	Function
1	VIN	power_in	Voltage monitor and supply input connected to an internal high-value resistive divider; the output is pulled low if VIN falls below the UVLO threshold minus hysteresis, and output logic is not guaranteed below 1.2V.
2	NC	unconnected	No internal connection; this unconnected pin sits between high-voltage and low-voltage pins to help maintain PCB trace clearance.
3	NC	unconnected	No internal connection; this unconnected pin sits between high-voltage and low-voltage pins to help maintain PCB trace clearance.
4	NC	unconnected	No internal connection; this unconnected pin sits between high-voltage and low-voltage pins to help maintain PCB trace clearance.
5	NC	unconnected	No internal connection; this unconnected pin sits between high-voltage and low-voltage pins to help maintain PCB trace clearance.
6	REF	power_out	Buffered reference output at VREF with respect to GND; bypass with a maximum of 1nF unless a damping resistor is used.
7	INH	input	High comparator reference input whose voltage is multiplied by the range setting to set the VIN rising threshold; keep it within the common-mode range VCM (0.35V to 2.45V) or tie it to GND to enable built-in hysteresis.
8	INL	input	Low comparator reference input whose voltage is multiplied by the range setting to set the VIN falling threshold; keep it within VCM or tie it to GND to enable built-in hysteresis, since oscillation occurs if INL is greater than INH unless built-in hysteresis is enabled.
9	PS	input	Polarity select input; connect to REF or to a voltage above VTH for an inverting output with respect to VIN, or to GND for a noninverting output.
10	RS	input	Range select input; connect to GND for the 10x range (RS = L) or to REF for the 40x range (RS = H).
11	GND	power_in	Device ground, the reference for all voltages on the part.
12	NC	unconnected	No internal connection; this unconnected pin sits between high-voltage and low-voltage pins to help maintain PCB trace clearance.
13	NC	unconnected	No internal connection; this unconnected pin sits between high-voltage and low-voltage pins to help maintain PCB trace clearance.
14	NC	unconnected	No internal connection; this unconnected pin sits between high-voltage and low-voltage pins to help maintain PCB trace clearance.
15	NC	unconnected	No internal connection; this unconnected pin sits between high-voltage and low-voltage pins to help maintain PCB trace clearance.
16	OUT	output	Comparator output with a high-voltage active pull-down and a gated 500kΩ pull-up to an internal supply of 3.5V to 5V; it can be externally pulled up to 100V and is pulled low during UVLO.

Key specifications

Parameter	Value
Manufacturer	Analog Devices
Package	MSOP-16
Category	Power Management ICs
Pins	16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter	Symbol	Min	Typ	Max	Unit	Conditions	Page
VIN Input Supply Operating Range	VIN	3.5		100	V	Over full operating temperature range (l)	3
VIN Monitor Range	VMON	3.5		98	V		3
VIN Input Supply Current	IVIN	3	7	15	µA	VIN = 100V, 40x; over full operating temperature range (l)	3
Undervoltage Lockout	VUVLO			3	V	VIN rising; over full operating temperature range (l)	3
Undervoltage Lockout Hysteresis			70		mV	VIN falling	3
Comparator Common Mode Voltage	VCM	0.35		2.45	V	Over full operating temperature range (l)	3
VIN Error Voltage at 96V	VERR	-1360		1360	mV	INH = VREF, 40x; over full operating temperature range (l)	3
VIN Error Voltage at 96V	VERR	-400		400	mV	0.35V ≤ INH ≤ 2.4V, 40x; over full operating temperature range (l)	3
VIN Error Voltage at 24V	VERR	-315		315	mV	INH = VREF, 10x; over full operating temperature range (l)	3
VIN Error Voltage at 24V	VERR	-75		75	mV	0.35V ≤ INH ≤ 2.4V, 10x; over full operating temperature range (l)	3
Comparator Offset Voltage	VOS	-3		3	mV	INH = 0.35V, 10x; over full operating temperature range (l)	3
Internal Resistive Divider Range Error	AVERR	-0.4		0.4	%	INH = 2.4V, Range = 10x, 40x; over full operating temperature range (l)	3
Comparator Built-in Hysteresis	VHYS	14	22	30	mV	INH = GND, INL rising, VIN = 24V; over full operating temperature range (l)	3
Comparator Built-in Hysteresis	VHYS	-30	-22	-14	mV	INL = GND, INH falling, VIN = 24V; over full operating temperature range (l)	3
Built-in Hysteresis Enable Threshold	VHYTH	100		175	mV	Over full operating temperature range (l)	3
VIN to OUT Comparator Propagation Delay	tPD		40	80	µs	Overdrive = 10%, OUT falling, 10x; INH = GND, INL = 1.2V; over full operating temperature range (l)	3
Input Leakage Current (INH, INL)	IIN(LKG)	-1		1	nA	V = 1.2V, I-Grade; over full operating temperature range (l)	3
Reference Output Voltage	VREF	2.378	2.402	2.426	V	IREF ≤ 100µA, VIN ≥ 3.5V; over full operating temperature range (l)	3
Select Input Threshold	VTH	0.4		1.4	V	RS, PS; over full operating temperature range (l)	3
Input Leakage Current	ILKG	-100		100	nA	V = 2.4V; RS, PS; over full operating temperature range (l)	3
Voltage Output Low	VOL			100	mV	VIN = 1.25V, I = 10µA; over full operating temperature range (l)	3
Voltage Output Low	VOL			400	mV	VIN = 3.5V, I = 500µA; over full operating temperature range (l)	3
Voltage Output High	VOH	2	2.375	2.75	V	VIN = 3.5V, I = -1µA; over full operating temperature range (l)	3
Voltage Output High	VOH	2.8	3	4	V	VIN ≥ 4.5V, I = -1µA; over full operating temperature range (l)	3
Output Current High	IOH	-15	-7.5	-5	µA	V = GND, VIN = 3.5V; over full operating temperature range (l)	3
Leakage Current, Output High	IO(LKG)	-250		250	nA	V = 100V, VIN = 6V; over full operating temperature range (l)	3
Absolute Maximum VIN Input Voltage	VIN	-0.3		140	V	Input Voltages	2
Absolute Maximum PS, RS Input Voltage	PS, RS	-0.3		6	V	Input Voltages	2
Absolute Maximum INH, INL Input Voltage	INH, INL	-0.3		6	V	Input Voltages	2
Absolute Maximum OUT Voltage	OUT	-0.3		140	V	Output Voltages	2
Absolute Maximum VIN Average Current	VIN	-20			mA	Average current	2
Absolute Maximum OUT Average Current	OUT	-5		5	mA	Average current (±5mA)	2
Absolute Maximum REF Average Current	REF	-5		5	mA	Average current (±5mA)	2
Absolute Maximum INH, INL Average Current	INH, INL	-1			mA	Average current	2
Operating Ambient Temperature Range (LTC2965I)	TA	-40		85	°C	Grade I (IMS#PBF)	2
Storage Temperature Range	TSTG	-65		150	°C		2
Maximum Junction Temperature	TJMAX			150	°C		2
Thermal Resistance, Junction to Ambient (MS16)	θJA		120		°C/W	16-Lead MSOP package	2

CAD (KiCad official)

Symbol: LTC2965IMS#PBF
Footprint: Package_SO:MSOP-16_3x4.039mm_P0.5mm
3D model: MSOP-16 (KiCad packages3D, STEP)
3D model files: ltc2965ims-pbf-etched.step / ltc2965ims-pbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ltc2965ims-pbf.step / ltc2965ims-pbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

Datasheet: Analog Devices datasheet (18 pp, sha256 a4223d1da4bb030d, retrieved 2026-10-30, tier: manufacturer)
Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF

LTC2965IMS#PBF

Verified LTC2965IMS#PBF

Verification log 1 record

3D Model

Symbol & Footprint

Schematic Symbol

PCB Footprint

Datasheet

README