component
PFS154-S16
Public Made by Adomby adom
PADAUK Tech Microcontrollers (MCU/MPU/SOC), SOP-16. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownPFS154-S16
PADAUK Tech · Microcontrollers (MCU/MPU/SOC) · SOP-16
PFS154-S16 from PADAUK Tech, in a SOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PB4/TM2PWM/PG0PWM | bidirectional | Port B bit 4 digital input or two-state output with optional pull-up, Timer2 output or PWMG0 output; digital input must be disabled via pbdier bit 4 when used as analog input. |
| 2 | PB5/TM3PWM/PG0PWM | bidirectional | Port B bit 5 digital input or two-state output with optional pull-up, Timer3 output or PWMG0 output; can wake the system unless pbdier bit 5 is 0. |
| 3 | PB6/TM3PWM/CIN2-/PG1PWM | bidirectional | Port B bit 6 digital I/O with optional pull-up, comparator minus input 2, Timer3 output or PWMG1 output; disable digital input via pbdier bit 6 when used as analog input. |
| 4 | PB7/TM3PWM/CIN3-/PG1PWM | bidirectional | Port B bit 7 digital I/O with optional pull-up, comparator minus input 3, Timer3 output or PWMG1 output; disable digital input via pbdier bit 7 when used as analog input. |
| 5 | VDD | power_in | Positive power supply, operating range 2.0V to 5.5V. |
| 6 | PA7/X1 | bidirectional | Port A bit 7 digital I/O with optional pull-up, or crystal oscillator X1; disable digital input via padier bit 7 when used for crystal. |
| 7 | PA6/X2 | bidirectional | Port A bit 6 digital I/O with optional pull-up, or crystal oscillator X2; disable digital input via padier bit 6 when used for crystal. |
| 8 | PA5/PRST#/PG2PWM | bidirectional | Port A bit 5 digital input or open-drain output, hardware reset PRST#, or PWMG2 output; a 33 ohm series resistor is recommended for noise immunity in input mode. |
| 9 | PA3/TM2PWM/COM4/CIN1-/PG2PWM | bidirectional | Port A bit 3 digital I/O with optional pull-up, comparator minus input 1, Timer2 output, LCD COM4 (1/2 VDD) or PWMG2 output. |
| 10 | PA4/COM3/CIN+/CIN4-/PG1PWM | bidirectional | Port A bit 4 digital I/O with optional pull-up, LCD COM3 (1/2 VDD), comparator plus input or minus input 4, or PWMG1 output. |
| 11 | PA0/INT0/COM2/CO/PG0PWM | bidirectional | Port A bit 0 digital I/O with optional pull-up, external interrupt 0 (both edges), comparator output, PWMG0 output or LCD COM2 (1/2 VDD). |
| 12 | GND | power_in | Ground. |
| 13 | PB0/INT1/COM1 | bidirectional | Port B bit 0 digital I/O with optional pull-up, external interrupt 1 (both edges) or LCD COM1 (1/2 VDD). |
| 14 | PB1 | bidirectional | Port B bit 1 digital input or two-state output with optional pull-up; disable digital input via pbdier bit 1 when used as analog input. |
| 15 | PB2/TM2PWM/PG2PWM | bidirectional | Port B bit 2 digital I/O with optional pull-up, Timer2 output or PWMG2 output. |
| 16 | PB3/PG2PWM | bidirectional | Port B bit 3 digital I/O with optional pull-up or PWMG2 output. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | PADAUK Tech |
| Package | SOP-16 |
| Category | Embedded Processors & Controllers |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDD Operating Voltage | VDD | 2 | 5.5 | V | Subject to LVR tolerance | 16 | |
| Low Voltage Reset tolerance | LVR% | -5 | 5 | % | 16 | ||
| System clock fSYS, IHRC/2 | fSYS | 0 | 8 | MHz | VDD ≧ 3.5V | 16 | |
| System clock fSYS, IHRC/4 | fSYS | 0 | 4 | MHz | VDD ≧ 2.5V | 16 | |
| System clock fSYS, IHRC/8 | fSYS | 0 | 2 | MHz | VDD ≧ 2.0V | 16 | |
| System clock fSYS, ILRC | fSYS | 70 | KHz | VDD = 3V | 16 | ||
| Operating Current, IHRC/16 (1MIPS) | IOP | 0.3 | mA | fSYS=IHRC/16=1MIPS@3V | 16 | ||
| Operating Current, ILRC | IOP | 12 | uA | fSYS=ILRC=70KHz@3V | 16 | ||
| Operating Current, EOSC (reserved) | IOP | 10 | uA | fSYS=EOSC=32KHz@3V (reserved) | 16 | ||
| Power Down Current (stopsys) | IPD | 0.5 | uA | fSYS= 0Hz, VDD =3.3V | 16 | ||
| Power Save Current (stopexe, IHRC disabled) | IPS | 5 | uA | VDD =3.3V | 16 | ||
| Input low voltage for IO lines | VIL | 0 | V | 16 | |||
| IO lines sink current (normal), PA0,PA3,PA4,PB2,PB5,PB6 | IOL | 10 | mA | VDD=3.3V, VOL=0.33V | 16 | ||
| IO lines sink current (normal), PA6,PA7,PB0,PB1,PB3,PB4,PB7 | IOL | 6 | mA | VDD=3.3V, VOL=0.33V | 16 | ||
| IO lines sink current (normal), PA5 | IOL | 5 | mA | VDD=3.3V, VOL=0.33V | 16 | ||
| IO lines sink current (low), PA5 | IOL | 5 | mA | VDD=3.3V, VOL=0.33V | 16 | ||
| IO lines sink current (low), others | IOL | 2 | mA | VDD=3.3V, VOL=0.33V | 16 | ||
| IO lines drive current (normal) | IOH | -5 | mA | VDD=3.3V, VOH=2.97V | 16 | ||
| IO lines drive current (low) | IOH | -1.6 | mA | 16 | |||
| Input voltage | VIN | -0.3 | V | 16 | |||
| Injected current on pin | IINJ(PIN) | 1 | mA | VDD +0.3≧VIN≧ -0.3 | 16 | ||
| Pull-high Resistance | RPH | 200 | KΩ | VDD=3.3V | 16 | ||
| Frequency of IHRC after calibration (5V, 25°C) | fIHRC | 15.84 | 16 | 16.16 | MHz | VDD=5V, Ta=25°C | 16 |
| Frequency of IHRC after calibration (2.2V-5.5V, -20 to 70°C) | fIHRC | 15.2 | 16.8 | MHz | VDD =2.2V~5.5V, -20°C <Ta<70°C | 16 | |
| Frequency of IHRC after calibration (2.0V-5.5V, -20 to 70°C) | fIHRC | 13.6 | 18.4 | MHz | VDD =2.0V~5.5V, -20°C <Ta<70°C | 16 | |
| Interrupt pulse width | tINT | 30 | ns | VDD = 3.3V | 16 | ||
| RAM data retention voltage | VDR | 1.5 | V | In power-down mode | 16 | ||
| Watchdog timeout period, misc[1:0]=00 (default) | tWDT | 8192 | TILRC | misc[1:0]=00 (default) | 17 | ||
| Watchdog timeout period, misc[1:0]=01 | tWDT | 16384 | TILRC | misc[1:0]=01 | 17 | ||
| Watchdog timeout period, misc[1:0]=10 | tWDT | 65536 | TILRC | misc[1:0]=10 | 17 | ||
| Watchdog timeout period, misc[1:0]=11 | tWDT | 262144 | TILRC | misc[1:0]=11 | 17 | ||
| System boot-up period, normal boot-up | tSBP | 47 | ms | @ VDD =5V | 17 | ||
| System boot-up period, fast boot-up | tSBP | 780 | us | 17 | |||
| Wake-up time period, fast wake-up | tWUP | 45 | TILRC | Fast wake-up | 17 | ||
| Wake-up time period, normal wake-up | tWUP | 3000 | TILRC | Normal wake-up | 17 | ||
| External reset pulse width | tRST | 120 | us | 17 | |||
| Comparator offset | CPos | -20 | 10 | 20 | mV | 17 | |
| Comparator input common mode | CPcm | 0 | V | 17 | |||
| Comparator response time | CPspt | 100 | 500 | ns | Both rising and falling | 17 | |
| Stable time to change comparator mode | CPmc | 2.5 | 7.5 | us | 17 | ||
| Comparator current consumption | CPcs | 20 | uA | VDD = 3.3V | 17 | ||
| Supply Voltage | 2 | 5.5 | V | Maximum Rating 5.5V | 17 | ||
| Input Voltage | -0.3 | V | 17 | ||||
| Operating Temperature | -20 | 70 | °C | 17 | |||
| Storage Temperature | -50 | 125 | °C | 17 | |||
| Junction Temperature | 150 | °C | 17 |
CAD (KiCad official)
- Symbol:
PFS154-S16 - Footprint:
Package_SO:SOIC-16_3.9x9.9mm_P1.27mm - 3D model: SOP-16 (KiCad packages3D, STEP)
- 3D model files:
pfs154-s16-etched.step/pfs154-s16-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pfs154-s16.step/pfs154-s16.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: PADAUK Tech datasheet (85 pp, sha256
2a29a45406cd553d, retrieved 2026-10-19, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text+vision), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).