Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

XTSDQ01GWSIGA

XTX · NAND FLASH · WSON-8-EP(6x8)

XTSDQ01GWSIGA from XTX, in a WSON-8-EP(6x8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 DAT2 bidirectional SD mode Data Line [bit2], push-pull I/O that is an input on power up and starts operating as a DAT line after the SET_BUS_WIDTH command; reserved in SPI mode.
2 DAT3/CD bidirectional SD mode Data Line [bit3] / SD NAND detection (internal 10-90 kOhm pull-up that may be used for card detection), input on power up; Chip Select input in SPI mode.
3 CLK input Clock input in both SD and SPI modes, up to 50MHz in high speed mode and 25MHz in default mode.
4 VSS power_in Ground supply in both SD and SPI modes.
5 CMD bidirectional Command/Response push-pull line in SD mode (10-100 kOhm pull-up recommended to prevent bus floating); Data In input in SPI mode.
6 DAT0 bidirectional SD mode Data Line [bit0], push-pull I/O; Data Out push-pull output in SPI mode.
7 DAT1 bidirectional SD mode Data Line [bit1], push-pull I/O that is an input on power up and starts operating as a DAT line after the SET_BUS_WIDTH command; reserved in SPI mode.
8 VDD power_in Supply voltage of 1.7V to 1.95V for the XTSDQ series (absolute maximum 2.25V), with max 5uF capacitance on the supply line and 45uF decoupling recommended.
9 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer XTX
Package WSON-8-EP(6x8)
Category Memory
Pins 9

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage VDD 1.7 1.95 V TA=-40°C to 85°C 19
Input Leakage Current ILI -2 2 µA 19
Output Leakage Current ILO -2 2 µA 19
Standby Current ICC1 130 2500 µA VDD=1.95V 19
Read Current ICC2 32 75 mA FCLK=50MHz 19
Write Current ICC2 32 75 mA FCLK=50MHz 19
Input Low Voltage VIL -0.3 V 19
Output Low Voltage VOL 0.4 V IOL = 2mA 19
Operating Temperature -40 85 °C 16
Storage Temperature -55 125 °C 16
VDD (XTSDQ0x Series) VDD -0.3 2.25 V 16
Voltage on I/O Pin with Respect to Ground (XTSDQ0x Series) -0.3 2.25 V -0.3V to VDD+0.3 (<= 2.25V) 16
Total bus capacitance for each signal line CL 40 pF CHOST+CBUS <= 30pF 16
Single card capacitance CCARD 10 pF 16
Pull-up resistance RCMD 10 100 K Ohm Prevent bus floating 16
Maximum signal line inductance 16 nH fPP <= 20MHz 16
Pull-up resistance inside card(pin1) RDAT3 10 90 K Ohm May be used for card detection 16
Capacity connected to power line CC 5 uF To prevent inrush current 16
Clock frequency Data Transfer Mode (default) fPP 25 MHz Default mode, CL=30pF 22
Clock frequency Identification Mode fOD 0 100 400 KHz Default mode, CL=30pF 22
Clock low time (default) tWL 10 ns Default mode 22
Clock high time (default) tWH 10 ns Default mode 22
Clock rise time (default) tTLH 10 ns Default mode 22
Clock fall time (default) tTHL 10 ns Default mode 22
Input setup time (default) tISU 5 ns Default mode 22
Input hold time (default) tIH 5 ns Default mode 22
Output delay time during Data Transfer Mode (default) tODLY 0 14 ns Default mode 22
Output delay time during Identification Mode tODLY 0 50 ns Default mode 22
Clock frequency Data Transfer Mode (high-speed) fPP 50 MHz High-speed mode, CL=30pF 24
Clock low time (high-speed) tWL 7 ns High-speed mode 24
Clock high time (high-speed) tWH 7 ns High-speed mode 24
Clock rise time (high-speed) tTLH 3 ns High-speed mode 24
Clock fall time (high-speed) tTHL 3 ns High-speed mode 24
Input setup time (high-speed) tISU 6 ns High-speed mode 24
Input hold time (high-speed) tIH 2 ns High-speed mode 24
Output delay time during Data Transfer Mode (high-speed) tODLY 0 14 ns High-speed mode 24
Output Hold time tOH 2.5 ns High-speed mode 24
Total system capacitance for each line (high-speed) CL 40 pF High-speed mode 24

CAD (KiCad official)

  • Symbol: XTSDQ01GWSIGA
  • Footprint: Package_SON:WSON-8-1EP_8x6mm_P1.27mm_EP3.4x4.3mm
  • 3D model: WSON-8-EP(6x8), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.75 mm nominal WSON height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
  • 3D model files: xtsdq01gwsiga-etched.step / xtsdq01gwsiga-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); xtsdq01gwsiga.step / xtsdq01gwsiga.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: XTX datasheet (28 pp, sha256 142239cf2c5e274e, retrieved 2026-10-22, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF