component
FT24C128A-ESR-B
Public Made by Adomby adom
FMD(Fremont Micro Devices) EEPROM, SOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownFT24C128A-ESR-B
FMD(Fremont Micro Devices) · EEPROM · SOP-8
FT24C128A-ESR-B from FMD(Fremont Micro Devices), in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 4 | GND | power_in | Ground reference for the device; input voltage on any pin is rated -0.3V to VCC + 0.3V relative to ground. |
| 5 | SDA | bidirectional | Serial data line, a bi-directional open-drain signal that can be wired-OR with other open-drain devices and is typically pulled high by an external resistor. |
| 6 | SCL | input | Serial clock input where the rising edge latches data into the EEPROM and the falling edge clocks data out, with a maximum clock frequency of 400 kHz at 1.8V and 1000 kHz at 2.5-5.0V. |
| 7 | WP | input | Write protect input that disables all programming functions when connected to VIH or VCC, while programming is allowed when it is left unconnected or at VIL and reads are unaffected. |
| 8 | VCC | power_in | Power supply pin with an operating range of 1.8V to 5.5V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | FMD(Fremont Micro Devices) |
| Package | SOP-8 |
| Category | Memory |
| Pins | 5 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage (24C××A supply VCC) | VCC1 | 1.8 | 5.5 | V | 9 | ||
| Supply read current | ICC | 0.4 | 1 | mA | VCC @ 5.0V SCL = 100 kHz | 9 | |
| Supply write current | ICC | 2 | 3 | mA | VCC @ 5.0V SCL = 100 kHz | 9 | |
| Supply current | ISB1 | 0.02 | 1 | µA | VCC @ 1.8V, VIN = VCC or VSS | 9 | |
| Supply current | ISB2 | 1 | µA | VCC @ 2.5V, VIN = VCC or VSS | 9 | ||
| Supply current | ISB3 | 0.07 | 1 | µA | VCC @ 5.0V, VIN = VCC or VSS | 9 | |
| Input leakage current | IIL | 3 | µA | VIN = VCC or VSS | 9 | ||
| Output leakage current | ILO | 3 | µA | VIN = VCC or VSS | 9 | ||
| Input low level | VIL | -0.6 | V | 9 | |||
| Output low level | VOL2 | 0.4 | V | VCC @ 3.0V, IOL = 2.1 mA | 9 | ||
| Clock frequency, SCL | fSCL | 400 | kHz | 1.8V column | 8 | ||
| Clock pulse width low | tLOW | 1.3 | µs | 1.8V column | 8 | ||
| Clock pulse width high | tHIGH | 0.6 | µs | 1.8V column | 8 | ||
| Noise suppression time | tI | 100 | ns | 1.8V column | 8 | ||
| Clock low to data out valid | tAA | 0.9 | µs | 1.8V column | 8 | ||
| Time the bus must be free before a new transmission can start | tBUF | 1.3 | µs | 1.8V column | 8 | ||
| START hold time | tHD.STA | 0.6 | µs | 1.8V column | 8 | ||
| START set-up time | tSU.STA | 0.6 | µs | 1.8V column | 8 | ||
| Data in hold time | tHD.DAT | 0 | µs | 1.8V column | 8 | ||
| Data in set-up time | tSU.DAT | 100 | ns | 1.8V column | 8 | ||
| Input rise time | tR | 0.3 | µs | 1.8V column | 8 | ||
| Input fall time | tF | 300 | ns | 1.8V column | 8 | ||
| STOP set-up time | tSU.STO | 0.6 | µs | 1.8V column | 8 | ||
| Data out hold time | tDH | 50 | ns | 1.8V column | 8 | ||
| Write cycle time | tWR | 5 | ms | 1.8V column | 8 | ||
| Clock frequency, SCL | fSCL | 1000 | kHz | 2.5-5.0 V column | 8 | ||
| Clock pulse width low | tLOW | 0.4 | µs | 2.5-5.0 V column | 8 | ||
| Clock pulse width high | tHIGH | 0.4 | µs | 2.5-5.0 V column | 8 | ||
| Noise suppression time | tI | 50 | ns | 2.5-5.0 V column | 8 | ||
| Clock low to data out valid | tAA | 0.55 | µs | 2.5-5.0 V column | 8 | ||
| Time the bus must be free before a new transmission can start | tBUF | 0.5 | µs | 2.5-5.0 V column | 8 | ||
| START hold time | tHD.STA | 0.25 | µs | 2.5-5.0 V column | 8 | ||
| START set-up time | tSU.STA | 0.25 | µs | 2.5-5.0 V column | 8 | ||
| Input fall time | tF | 100 | ns | 2.5-5.0 V column | 8 | ||
| STOP set-up time | tSU.STO | 0.25 | µs | 2.5-5.0 V column | 8 | ||
| Endurance (write cycles) | 1e+06 | Write Cycles | 25oC, Page Mode, 3.3V | 8 | |||
| Industrial operating temperature | -40 | 85 | ℃ | 2 | |||
| Storage temperature | -50 | 125 | ℃ | 2 | |||
| Input voltage on any pin relative to ground | -0.3 | V | relative to ground | 2 | |||
| Maximum voltage | 8 | V | 2 | ||||
| ESD protection on all pins | 2000 | V | all pins | 2 |
CAD (KiCad official)
- Symbol:
FT24C128A-ESR-B - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOP-8 (KiCad packages3D, STEP)
- 3D model files:
ft24c128a-esr-b-etched.step/ft24c128a-esr-b-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ft24c128a-esr-b.step/ft24c128a-esr-b.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: FMD(Fremont Micro Devices) datasheet (16 pp, sha256
8365e4d4ae03832f, retrieved 2026-11-05, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).