Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

SEC1210I-CN-02

Microchip Tech · Interface - Specialized · QFN-24(5x5)

SEC1210I-CN-02 from Microchip Tech, in a QFN-24(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, read twice and the reads agreed); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SC2_RST_N output Smart Card 2 reset output (also GPIO18); a low pulse resets the card and triggers an ATR, and it should be held low when the interface is not active.
2 SC2_VCC power_out Smart Card 2 supply output settable to 1.8, 3.0 or 5.0 V depending on card type, powered down at reset, and requires an external 1 µF capacitor.
3 VDD5 power_in 5.0 V (or VBUS) power input; the supply input range is 3.6 V to 5.5 V.
4 SC1_C8 bidirectional Smart Card 1 C8 contact for standard or proprietary use as input and/or output (also GPIO4).
5 SC1_C4 bidirectional Smart Card 1 C4 contact for cards that support Function Code (also GPIO3).
6 SC1_IO bidirectional Smart Card 1 bidirectional serial data pin (also GPIO0), which should be held low when the interface is not active.
7 SC1_CLK output Smart Card 1 clock output (also GPIO1), which should be held low when the interface is not active.
8 SC1_RST_N output Smart Card 1 reset output (also GPIO2); a low pulse resets the card and triggers an ATR, and it should be held low when the interface is not active.
9 SC1_VCC power_out Smart Card 1 supply output settable to 1.8, 3.0 or 5.0 V depending on card type, powered down at reset, and requires an external 1 µF capacitor.
10 SC1_PRSNT_N/JTAG_TMS bidirectional Active-low Smart Card 1 presence detect with software-activated internal pull-up, alternatively JTAG_TMS in debug mode, GPIO6 or Timer 0 input.
11 SPI1_MISO/RXD bidirectional SPI1 host data input to the controller (needs a weak internal pull-down at all times), alternatively UART RXD input or GPIO8.
12 SPI1_CLK/CTS bidirectional SPI1 clock output in host mode, alternatively UART CTS or GPIO10.
13 SPI1_CE/RTS bidirectional Active-low SPI1 chip-enable output in host mode (drive high in idle if SPI1 is disabled), alternatively UART RTS or GPIO11.
14 SPI1_MOSI/TXD bidirectional SPI1 host data output from the controller, alternatively UART TXD output or GPIO9.
15 TEST input Chip test signal with a weak pull-down at reset; it must be tied low externally if the test function is not used.
16 USB_DM bidirectional USB D- data line connecting to the upstream USB bus, with integrated series termination resistor.
17 USB_DP bidirectional USB D+ data line connecting to the upstream USB bus, with integrated 1.5 k pull-up and series resistor.
18 VDD33 power_out 3.3 V internal regulator output for USB and GPIO I/O supply, requiring an external 1 µF decoupling capacitor.
19 JTAG_CLK bidirectional JTAG debug clock input with weak pull-down, which can be left floating or grounded when not used.
20 SC_LED_ACT_N/JTAG_TDO bidirectional Driver for the active LED, alternatively JTAG_TDO in debug mode, GPIO5 or Timer 2 t2ex input.
21 SC2_PRSNT_N/JTAG_TDI bidirectional Active-low Smart Card 2 presence detect with software-activated pull-up, alternatively JTAG_TDI or GPIO19, with weak pull-down at reset.
22 RESET_N input Active-low analog reset input (Vil=100 mV) that resets the chip and enters STOP mode, with a pulse at least 1 µs wide.
23 SC2_IO bidirectional Smart Card 2 bidirectional serial data pin (also GPIO16), which should be held low when the interface is not active.
24 SC2_CLK output Smart Card 2 clock output (also GPIO17), which should be held low when the interface is not active.
25 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package QFN-24(5x5)
Category Communication Interface Chip/UART/485/232
Pins 25

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Storage Temperature TSTOR -55 150 °C 188
VDD5 supply voltage VDD5 -0.3 5.5 V 188
Voltage on any signal pin -0.3 5.5 V 188
Voltage on USB_DP and USB_DM pins -0.3 3.6 V 3.3 V 10% 188
Voltage on RESET_N 0 V VDD5 (Note 18-3) 188
Operating Temperature TA -40 85 °C Ambient temperature in air; industrial range per Notes 18-1 and 18-2 189
5.0V supply voltage VDD5 3.6 5.5 V 189
Voltage on USB_DP and USB_DM pins 3 3.6 V If VDD5 drops below 3.6V, then the MAX becomes VDD5 189
Voltage on RESET_N 0 V 189
Voltage on any signal pin -0.3 5.5 V Other than USB_DP, USB_DM, Smart Card pins, RESET_N 189
VDD5 supply rise time tRT 400 ns Figure 18-1 189
Low Output Level VOL 0.4 V IOL = -8 mA 189
8 mA I/O sinking current IOL8 8.3 12.6 18.4 mA VOUT = 0.4V 189
8 mA I/O sinking output impedance ROL8 21.7 31.6 48.3 VOUT = 0.4V 189
8 mA I/O sourcing current IOH8 8.1 11.6 16 mA VOUT = VDD33 - 0.4V 189
8 mA I/O sourcing output impedance ROH8 25 34.6 50 VOUT = VDD33 - 0.4V 189
Output Leakage IIH5 1 µA VIN= 0 to VDD33,27°C 189
Output Leakage IIH5 1.4 8 12 µA VIN = 0 to 5.5V, 27°C 189
Output Leakage IIH5 20 µA VIN = 0 to 5.5V, 85°C 189
Output Leakage IIH5 80 µA VIN=0 to 5.5V,125°C 189
Low Input Level VIL -0.3 0.8 V 189
High Input Level VIH5 2 5.5 V 189
Hysteresis VHYSI 336 399 459 mV 189
Pull-Down RDPD 46 65 90 k Vpad = VDD33 189
Pull-Down current IDPD 33 50 79 µA Vpad = VDD33 189
Pull-Up RDPU 53 66 80 k Vpad = 0V 189
Pull-Up current IDPU 38 50 68 µA Vpad = 0V 189
RESET_N Rise Time Trst_r 100 ns RESET_N pad 190
RESET_N Fall Time Trst_f 100 ns RESET_N pad 190
RESET_N Low Input level VILRST 0.1 V RESET_N low causes STOP mode entry 190
Internal oscillator 48 MHz accuracy with USB dynamic trim F48acc 0.1 0.2 % Internal oscillator @ 48 MHz with USB Dynamic Trim enabled 190
Internal oscillator 48 MHz accuracy without USB dynamic trim F48accd 0.82 1.5 % Internal oscillator @ 48 MHz without USB Dynamic Trim enabled 190
Internal oscillator 8 MHz accuracy F8acc 0.78 1.83 % Internal oscillator @ 8 MHz 190
Internal oscillator 4 MHz accuracy F4acc 0.78 1.83 % Internal oscillator @ 4 MHz 190
Smart Card Power Supply Voltage (Class A) VSC1_VCC, VSC2_VCC 4.6 V Class A mode, ISC1_VCC = 0 to 55 mA 190
Smart Card Power Supply Voltage (Class B) VSC1_VCC, VSC2_VCC 2.76 3 3.24 V Class B mode 190
Smart Card Power Supply Voltage (Class C) VSC1_VCC, VSC2_VCC 1.66 1.8 1.94 V Class C mode 190
Smart Card Power Supply current ISC1, ISC2 55 mA Class A/B/C 190
Smart Card Over Current Sense (OCS) Detection IOCS1, IOCS2 110 mA 190
Detection Time on OCS tOSCDET 1 µs 190
SC1_VCC/SC2_VCC Turn Off Time tSCOFF 5 ms SEC1110/SEC1210 A1 version 190
SC1_VCC/SC2_VCC Turn Off Time tSCOFF 500 µs All Later versions 190
SC1_VCC/SC2_VCC Turn On Time tSCON 1 ms 1.0 µF load 190
SC1_CLK/SC2_CLK Low Output Level (Class A) VOL 0 0.4 V Class A; @ CL=30pF 191
SC1_CLK/SC2_CLK Low Output Level (Class B) VOL 0 0.4 V Class B; @ CL=30pF 191
SC1_CLK/SC2_CLK Low Output Level (Class C) VOL 0 V Class C; @ CL=30pF 191
SC1_CLK/SC2_CLK Rise Time tR 9.9 13 16.67 ns @ CL = 30 pF, Rload=33 191
SC1_CLK/SC2_CLK Fall Time tF 6.5 10 16.2 ns @ CL = 30 pF, Rload=33 191
SC1_CLK/SC2_CLK Clock Accuracy (USB dynamic trimming on) 0.1 0.25 % USB Dynamic Trimming is on 191
SC1_CLK/SC2_CLK Clock Accuracy (USB dynamic trim off) 0.82 1.5 % USB Dynamic trim is off 191
SC1_CLK/SC2_CLK Clock Duty Cycle 48 52 % Oscillator in 48 MHz mode 191
SC1_CLK/SC2_CLK Frequency FSCx_CLK 1 4.8 MHz Generated by dividing 48 MHz by an integer ranging from 10 to 48 191

CAD (KiCad official)

  • Symbol: SEC1210I-CN-02
  • Footprint: Package_DFN_QFN:QFN-24-1EP_5x5mm_P0.65mm_EP3.2x3.2mm
  • 3D model: QFN-24(5x5) (KiCad packages3D, STEP)
  • 3D model files: sec1210i-cn-02-etched.step / sec1210i-cn-02-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); sec1210i-cn-02.step / sec1210i-cn-02.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (220 pp, sha256 3d50372dd19b6208, retrieved 2026-11-09, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF