3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownPAM2401YPADJ
Diodes Incorporated · DC-DC Converters · WDFN-12-EP(3x3)
PAM2401YPADJ from Diodes Incorporated, in a WDFN-12-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | LX | passive | LX is the switch pin of the step-up converter, connected to the internal N-channel MOSFET switch with RDS(ON) of 100 mΩ typical and 170 mΩ maximum. |
| 2 | LX | passive | LX is the switch pin of the step-up converter, connected to the internal N-channel MOSFET switch with RDS(ON) of 100 mΩ typical and 170 mΩ maximum. |
| 3 | EN | input | EN is the enable control input; the EN threshold high is 0.8V at VIN = 0.9V and 1.5V at VIN = 3.3V, and the threshold low is 0.2V for VIN > 1.2V. |
| 4 | VIN | power_in | VIN is the input voltage pin, with an input voltage range of 0.9V to 4.75V. |
| 5 | PG | output | PG is the power good indicator pin, an open drain output that indicates when the output reaches the power good threshold of 92%. |
| 6 | AGND | power_in | AGND is the analog ground pin of the device. |
| 7 | FB | input | FB is the feedback pin, internally set to 0.6V, with the output voltage set by an external resistor divider from VOUT to ground. |
| 8 | RSET | passive | RSET sets the N-channel current limit, which is 3A when floating or above 200kΩ, 1.5A at 100kΩ, and 1A at 66kΩ. |
| 9 | OUT | power_out | OUT is the output pin of the step-up converter, with an output voltage adjustable from 2.5V to 5.0V. |
| 10 | OUT | power_out | OUT is the output pin of the step-up converter, with an output voltage adjustable from 2.5V to 5.0V. |
| 11 | PGND | power_in | PGND is the power ground pin of the device. |
| 12 | PGND | power_in | PGND is the power ground pin of the device. |
| 13 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Diodes Incorporated |
| Package | WDFN-12-EP(3x3) |
| Category | Power Supply Chip |
| Pins | 13 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage Range | VIN | 0.9 | 4.75 | V | No load, VO = 5V | 4 | |
| Input Voltage Range | VIN | 2.7 | 4.75 | V | IO = 1A, VO = 5V | 4 | |
| Minimum Startup Voltage | VSTARTUP | 1 | V | IO = 0.1A, VO = 3.3V | 4 | ||
| Shutdown Supply Current | ISD | 0.1 | 1 | µA | 4 | ||
| Oscillator Frequency | fOSC | 0.8 | 1 | 1.2 | MHz | 4 | |
| Maximum Duty Cycle | DMAX | 87.5 | % | 4 | |||
| Output-Voltage Adjust Range | VO | 2.5 | 5 | V | 4 | ||
| FB Regulation Voltage | VFB | 0.588 | 0.6 | 0.612 | V | No Load | 4 |
| Load Regulation | LDR | 2.5 | % | IOUT = 1mA to 1000mA | 4 | ||
| Drain-Source On-State Resistance (P MOSFET) | RDS(ON) | 150 | 250 | mΩ | 4 | ||
| Drain-Source On-State Resistance (N MOSFET) | RDS(ON) | 100 | 170 | mΩ | 4 | ||
| SW Leakage Current | ILSW | 0.1 | 2 | µA | 4 | ||
| Quiescent Current | Iq | 150 | µA | No load, switching (measured with external feedback); VO = 5V | 4 | ||
| Line Regulation | LNR | 0.3 | %/V | VO = 2.5V to 4.75V, IO = 0.5A | 4 | ||
| N-Channel Current Limit | ILIMIT | 3 | A | RSET Floating or RSET > 200KΩ | 4 | ||
| N-Channel Current Limit | ILIMIT | 1.5 | A | RSET = 100KΩ | 4 | ||
| N-Channel Current Limit | ILIMIT | 1 | A | RSET = 66KΩ | 4 | ||
| Pre-charge Current | I-Charge | 500 | mA | VOUT +0.5V < VIN | 4 | ||
| Pre-charge Time | T-Charge | 400 | µs | VOUT +0.5V < VIN | 4 | ||
| Power Good Threshold | VPG | 92 | % | 4 | |||
| EN Threshold High | VH | 0.8 | V | VIN = 0.9V | 4 | ||
| EN Threshold High | VH | 1.5 | V | VIN = 3.3V | 4 | ||
| EN Threshold Low | VL | 0.2 | V | VIN > 1.2V | 4 | ||
| Over Temperature Threshold | TOTSD | 160 | °C | 4 | |||
| Over Temperature Hysteresis | THYS | 50 | °C | 4 | |||
| Input Voltage | -0.3 | 6 | V | 3 | |||
| SW Voltage | -0.3 | 6 | V | 3 | |||
| SHDN, FB Voltage | -0.3 | 6 | V | 3 | |||
| VOUT | -0.3 | 6 | V | 3 | |||
| Operating Temperature Range | -40 | 85 | °C | 3 | |||
| Storage Temperature Range | -65 | 125 | °C | 3 | |||
| Lead Temperature (Soldering) | 300 | °C | Soldering, 10 sec | 3 | |||
| Ambient Temperature Range | -40 | 85 | °C | 3 | |||
| Junction Temperature Range | -40 | 125 | 3 | ||||
| Thermal Resistance (Junction to Case), U-DFN3030-12 | ΘJC | 8.5 | °C/W | 3 | |||
| Thermal Resistance (Junction to Ambient), U-DFN3030-12 | ΘJC | 60 | °C/W | 3 | |||
| Internal Power Dissipation, U-DFN3030-12 | PD | 1.66 | W | 3 |
CAD (KiCad official)
- Symbol:
PAM2401YPADJ - Footprint:
Package_DFN_QFN:WDFN-12-1EP_3x3mm_P0.45mm_EP1.7x2.5mm - 3D model: WDFN-12-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
pam2401ypadj-etched.step/pam2401ypadj-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pam2401ypadj.step/pam2401ypadj.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Diodes Incorporated datasheet (10 pp, sha256
e3a025eaf6ee1a54, retrieved 2026-11-04, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).