3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLT3022EDHC#PBF
Analog Devices · Linear Voltage Regulators (LDO) · DFN-16-EP(3x5)
LT3022EDHC#PBF from Analog Devices, in a DFN-16-EP(3x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | No connection to internal circuitry; the pin may be floated, tied to VIN or tied to GND for improved thermal performance. |
| 2 | NC | unconnected | No connection to internal circuitry; the pin may be floated, tied to VIN or tied to GND for improved thermal performance. |
| 3 | OUT | power_out | Supplies power to the load; a minimum 10µF output capacitor is required to prevent oscillations and the LT3022 requires a 1mA minimum load current for proper regulation and stability. |
| 4 | OUT | power_out | Supplies power to the load; a minimum 10µF output capacitor is required to prevent oscillations and the LT3022 requires a 1mA minimum load current for proper regulation and stability. |
| 5 | ADJ | input | Error amplifier inverting terminal with a 200mV reference voltage referred to AGND and a 30nA typical input bias current flowing out of the pin. |
| 6 | AGND | power_in | Analog ground to be tied directly to PGND (pins 10, 11) and the exposed backside GND (pin 17), with the output-setting resistor divider connected directly to it. |
| 7 | AGND | power_in | Analog ground to be tied directly to PGND (pins 10, 11) and the exposed backside GND (pin 17), with the output-setting resistor divider connected directly to it. |
| 8 | NC | unconnected | No connection to internal circuitry; the pin may be floated, tied to VIN or tied to GND for improved thermal performance. |
| 9 | SHDN | input | Pulling low puts the LT3022 into a low power state and turns the output off; it can be driven by logic or an open-collector device with a pull-up, and the device does not function if this pin is left unconnected. |
| 10 | PGND | power_in | Power ground through which most of the ground pin current flows; tie directly to AGND (pins 6, 7) and the exposed backside GND (pin 17). |
| 11 | PGND | power_in | Power ground through which most of the ground pin current flows; tie directly to AGND (pins 6, 7) and the exposed backside GND (pin 17). |
| 12 | IN | power_in | Supplies power to the device with a minimum 10µF bypass capacitor suggested, and withstands reverse voltage on the input so no reverse current flows into the device when the battery is reversed. |
| 13 | IN | power_in | Supplies power to the device with a minimum 10µF bypass capacitor suggested, and withstands reverse voltage on the input so no reverse current flows into the device when the battery is reversed. |
| 14 | IN | power_in | Supplies power to the device with a minimum 10µF bypass capacitor suggested, and withstands reverse voltage on the input so no reverse current flows into the device when the battery is reversed. |
| 15 | NC | unconnected | No connection to internal circuitry; the pin may be floated, tied to VIN or tied to GND for improved thermal performance. |
| 16 | NC | unconnected | No connection to internal circuitry; the pin may be floated, tied to VIN or tied to GND for improved thermal performance. |
| 17 | GND | power_in | Exposed pad that must be tied directly to AGND (pins 6, 7), PGND (pins 10, 11) and the PCB ground to provide enhanced thermal performance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-16-EP(3x5) |
| Category | Power Supply Chip |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Minimum Input Voltage | 0.9 | 1.05 | V | ILOAD = 1A, TA > 0°C | 4 | ||
| Minimum Input Voltage | 0.9 | 1.1 | V | ILOAD = 1A, TA ≤ 0°C | 4 | ||
| ADJ Pin Voltage | 196 | 200 | 204 | mV | VIN = 1.5V, ILOAD = 1mA | 4 | |
| ADJ Pin Voltage | 194 | 200 | 206 | mV | 1.15V < VIN < 10V, 1mA < ILOAD < 1A, full temperature range | 4 | |
| Line Regulation | -1.5 | -0.1 | 0.5 | mV | ΔVIN = 1.15V to 10V, ILOAD = 1mA | 4 | |
| Load Regulation | -0.5 | 0.1 | 0.5 | mV | VIN = 1.15V, ΔILOAD = 1mA to 1A | 4 | |
| Load Regulation | -1 | 1 | mV | VIN = 1.15V, ΔILOAD = 1mA to 1A, full temperature range | 4 | ||
| Dropout Voltage | 45 | 75 | mV | ILOAD = 10mA | 4 | ||
| Dropout Voltage | 135 | mV | ILOAD = 10mA, full temperature range | 4 | |||
| Dropout Voltage | 55 | 90 | mV | ILOAD = 100mA | 4 | ||
| Dropout Voltage | 175 | mV | ILOAD = 100mA, full temperature range | 4 | |||
| Dropout Voltage | 110 | 150 | mV | ILOAD = 500mA | 4 | ||
| Dropout Voltage | 235 | mV | ILOAD = 500mA, full temperature range | 4 | |||
| Dropout Voltage | 145 | 185 | mV | ILOAD = 1A | 4 | ||
| Dropout Voltage | 285 | mV | ILOAD = 1A, full temperature range | 4 | |||
| GND Pin Current | 400 | µA | VIN = VOUT(NOMINAL) + 0.4V, ILOAD = 0mA | 4 | |||
| GND Pin Current | 1.2 | 3.5 | mA | VIN = VOUT(NOMINAL) + 0.4V, ILOAD = 1mA | 4 | ||
| GND Pin Current | 3.4 | 8.5 | mA | VIN = VOUT(NOMINAL) + 0.4V, ILOAD = 100mA | 4 | ||
| GND Pin Current | 8.3 | 20 | mA | VIN = VOUT(NOMINAL) + 0.4V, ILOAD = 500mA | 4 | ||
| GND Pin Current | 18 | 36 | mA | VIN = VOUT(NOMINAL) + 0.4V, ILOAD = 1A | 4 | ||
| Output Voltage Noise | 165 | µVRMS | COUT = 10µF, ILOAD = 1A, BW = 10Hz to 100kHz, VOUT = 1.2V | 4 | |||
| ADJ Pin Bias Current | 30 | 100 | nA | VADJ = 0.2V, VIN = 1.5V | 4 | ||
| Shutdown Threshold | 0.64 | 0.9 | V | VOUT = Off to On | 4 | ||
| Shutdown Threshold | 0.25 | 0.64 | V | VOUT = On to Off | 4 | ||
| SHDN Pin Current | 3 | 9.5 | µA | VSHDN = 0V, VIN = 10V | 4 | ||
| SHDN Pin Current | -1 | 1 | µA | VSHDN = 10V, VIN = 10V | 4 | ||
| Quiescent Current in Shutdown | 7.5 | 15 | µA | VIN = 6V, VSHDN = 0V | 4 | ||
| Ripple Rejection | 55 | 70 | dB | VIN, VOUT = 1V, VRIPPLE = 0.5VP-P, fRIPPLE = 120Hz, ILOAD = 1A | 5 | ||
| Current Limit | 2.6 | A | VIN = 10V, VOUT = 0V | 5 | |||
| Current Limit | 1.1 | 1.7 | A | VIN = VOUT(NOMINAL) + 0.5V, ΔVOUT ≤ -5%, full temperature range | 5 | ||
| Input Reverse Leakage Current | 4 | 40 | µA | VIN = -10V, VOUT = 0V | 5 | ||
| Reverse Output Current | 0.1 | 5 | µA | VOUT = 1.2V, VIN = 0V | 5 | ||
| Minimum Required Output Current | 1 | mA | VIN = 1.6V, VOUT = 1.2V, full temperature range | 5 | |||
| IN Pin Voltage | -10 | 10 | V | 2 | |||
| OUT Pin Voltage | -10 | 10 | V | 2 | |||
| Input-to-Output Differential Voltage | -10 | 10 | V | 2 | |||
| ADJ/SENSE Pin Voltage | -10 | 10 | V | 2 | |||
| SHDN Pin Voltage | -10 | 10 | V | 2 | |||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Junction Temperature Maximum | TJMAX | 125 | °C | DHC package | 2 | ||
| Operating Junction Temperature Range | -40 | 125 | °C | E-Grade (Notes 2, 3) | 2 | ||
| Thermal Resistance Junction-to-Ambient | θJA | 38 | °C/W | DHC package | 2 | ||
| Thermal Resistance Junction-to-Case | θJC | 4 | °C/W | DHC package | 2 | ||
| Thermal Resistance Junction-to-Ambient (copper area range) | θJA | 35 | 40 | °C/W | DHC package, 2500mm2 to 100mm2 topside copper area, 2500mm2 backside | 14 |
CAD (KiCad official)
- Symbol:
LT3022EDHC#PBF - Footprint:
Package_DFN_QFN:DFN-16-1EP_3x5mm_P0.5mm_EP1.66x4.4mm - 3D model: DFN-16-EP(3x5) (KiCad packages3D, STEP)
- 3D model files:
lt3022edhc-pbf-etched.step/lt3022edhc-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt3022edhc-pbf.step/lt3022edhc-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (20 pp, sha256
1e0a90f4431b0dec, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).