3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMPQ4436AGRE-AEC1-Z
Monolithic Power Systems · DC-DC Converters · QFN-20(4x4)
MPQ4436AGRE-AEC1-Z from Monolithic Power Systems, in a QFN-20(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | MODE | input | AAM or FCCM select pin: pull high to put the part in FCCM and pull low for AAM at light load, and do not leave it floating. |
| 2 | SYNCIN | input | SYNC input that synchronizes the internal oscillator to an external 350kHz to 1000kHz clock; connect a 51kΩ resistor between SYNCIN and GND, connect to GND if not used, and do not float it. |
| 3 | VIN | power_in | Input supply for the internal control circuitry and the power switch connected to SW, with a decoupling capacitor to ground recommended close to VIN. |
| 4 | PGND | power_in | Power ground. |
| 5 | PGND | power_in | Power ground. |
| 6 | BST | power_out | Bootstrap positive power supply for the high-side MOSFET driver connected to SW, requiring a bypass capacitor between BST and SW sized per the application section. |
| 7 | SW | output | Switch node and output of the internal power switch. |
| 8 | SW | output | Switch node and output of the internal power switch. |
| 9 | EN | input | Enable pin: pull below the 0.85V threshold to shut down the chip and pull above the 1V threshold to enable it. |
| 10 | PGND | power_in | Power ground. |
| 11 | PGND | power_in | Power ground. |
| 12 | VIN | power_in | Input supply for the internal control circuitry and the power switch connected to SW, with a decoupling capacitor to ground recommended close to VIN. |
| 13 | SYNCO | output | SYNC output providing a clock 180° out-of-phase with the internal oscillator or opposite to the SYNCIN clock; leave floating if not used. |
| 14 | PG | output | Open-drain power good output that goes high when the output is within 93% to 106% of nominal and low above 107.5% or below 91%, requiring a pull-up resistor to the power source if used. |
| 15 | ICS | passive | Current sharing pin: connect in parallel ICs in multi-phase applications, and in single-phase applications connect to VCC or to VOUT that is at least 3V; do not float it. |
| 16 | VCC | power_out | Bias supply powering the internal control circuit and gate drivers, requiring a decoupling capacitor to ground close to this pin. |
| 17 | AGND | power_in | Analog ground. |
| 18 | FB | input | Feedback input with a 0.815V feedback threshold voltage, connected to the center point of the output resistor divider to AGND and placed as close to FB as possible. |
| 19 | SS | passive | Soft start input: a capacitor from SS to GND sets the soft-start period, with a 6µA source current charging it at start-up to limit inrush current. |
| 20 | FREQ | input | Switching frequency program: a resistor from this pin to ground sets the switching frequency, following the fSW vs. RFREQ curve in the Typical Performance Characteristics section. |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | QFN-20(4x4) |
| Category | Power Supply Chip |
| Pins | 21 |
CAD (KiCad official)
- Symbol:
MPQ4436AGRE-AEC1-Z - Footprint:
Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm - 3D model: QFN-20(4x4) (KiCad packages3D, STEP)
- 3D model files:
mpq4436agre-aec1-z-etched.step/mpq4436agre-aec1-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mpq4436agre-aec1-z.step/mpq4436agre-aec1-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Monolithic Power Systems datasheet (38 pp, sha256
71ef689792c1986b, retrieved 2026-10-28, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).