3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMX35LF4G24AD-Z4I
MXIC(Macronix) · NAND FLASH · WSON-8(6x8)
MX35LF4G24AD-Z4I from MXIC(Macronix), in a WSON-8(6x8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CS# | input | Chip Select input; the device is active from a correct command until the next CS# rising edge, and an incorrect command keeps it in standby until the next CS# falling edge. |
| 2 | SO/SIO1 | bidirectional | Serial Data Output for 1 x I/O, or Serial Data Input & Output for 1-1-2, 1-1-4, 1-2-2 or 1-4-4 modes; High-Z in standby mode. |
| 3 | WP#/SIO2 | bidirectional | Write protection (connect to GND) or Serial Data Input & Output for 1-1-4 or 1-4-4 mode. |
| 4 | GND | power_in | Ground. |
| 5 | SI/SIO0 | bidirectional | Serial Data Input for 1 x I/O, or Serial Data Input & Output for 1-1-2, 1-1-4, 1-2-2 or 1-4-4 modes. |
| 6 | SCLK | input | Clock input; input data is latched on the rising edge and output data shifts out on the falling edge, supporting serial mode 0 and mode 3. |
| 7 | HOLD#/SIO3 | bidirectional | Hold or Serial Data Input & Output for 1-1-4 or 1-4-4 mode. |
| 8 | VCC | power_in | +3V power supply; the MX35LF4G24AD-Z4I is specified for a 2.7V to 3.6V VCC range. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | MXIC(Macronix) |
| Package | WSON-8(6x8) |
| Category | Memory |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Temperature under bias | -50 | 125 | °C | 56 | |||
| Storage temperature | -65 | 150 | °C | 56 | |||
| All input voltages with respect to ground | -0.6 | 4.6 | V | Note 2 | 56 | ||
| VCC supply voltage with respect to ground | VCC | -0.6 | 4.6 | V | Note 2 | 56 | |
| ESD protection | 2000 | V | >2000V | 56 | |||
| Operating temperature | -40 | 85 | °C | Operating Range | 57 | ||
| VCC supply voltage | VCC | 2.7 | 3.3 | 3.6 | V | Operating Range | 57 |
| Input capacitance | CIN | 10 | pF | TA=+25°C, F=1MHz, VIN=0V; 10pF for 4Gb | 57 | ||
| Output capacitance | COUT | 10 | pF | TA=+25°C, F=1MHz, VOUT=0V; 10pF for 4Gb | 57 | ||
| Input leakage current | ILI | -10 | 10 | uA | VIN= 0 to VCC Max. | 58 | |
| Output leakage current | ILO | -10 | 10 | uA | VOUT= 0 to VCC Max. | 58 | |
| VCC standby current (CMOS) | ISB1 | 15 | 50 | uA | VIN=VCC or GND, CS#=VCC | 58 | |
| VCC active current (Sequential Read) | ICC1 | 20 | 30 | mA | f=120MHz, Iout = 0mA | 58 | |
| VCC active current (Program) | ICC2 | 20 | 30 | mA | 58 | ||
| VCC active current (Erase) | ICC3 | 15 | 30 | mA | 58 | ||
| Input low level | VIL | -0.3 | 0.2 | V | max printed as 0.2VCC | 58 | |
| Output low voltage | VOL | 0.2 | V | IOL= -1mA | 58 | ||
| Serial Clock Frequency for all command | fC | 0 | 120 | MHz | Note 1; min printed D.C. | 58 | |
| CS# Diselect Time | tCS | 30 | ns | 58 | |||
| Output Disable Time | tDIS | 7 | ns | 58 | |||
| Serial Clock Low to Output Valid (30pF) | tV | 7 | ns | 30pF | 58 | ||
| Serial Clock Low to Output Valid (15pF) | tV | 6 | ns | 15pF | 58 | ||
| Output Hold Time | tHO | 1 | ns | 58 | |||
| Data In Setup Time | tSUDAT | 2 | ns | 58 | |||
| Data Input Hold Time | tHDDAT | 2 | ns | 58 | |||
| Serial Clock High Time | tWH | 3.75 | ns | 58 | |||
| Serial Clock Low Time | tWL | 3.75 | ns | 58 | |||
| Write protect Hold Time | tWPH | 100 | ns | 58 | |||
| Write protect Setup Time | tWPS | 20 | ns | 58 | |||
| VCC(min.) to device operation | tVSL | 5 | ms | 58 | |||
| Page programming time (Randomizer disabled) | tPROG | 320 | 700 | us | 59 | ||
| Page programming time (Randomizer enabled) | tPROG_RAND | 360 | 740 | us | 59 | ||
| Block Erase Time | tERASE | 4 | 6 | ms | 59 | ||
| Dummy busy time for cache read | tRCBSY | 4.5 | 25 | us | 59 | ||
| Data transfer from array to buffer | tRD | 25 | us | 59 | |||
| VCC voltage needs to be below VPWD for proper initialization | VPWD | 0.9 | V | 55 | |||
| Voltage threshold for re-initialization | V_keep | 2.4 | V | if VDD drops below V_KEEP | 55 | ||
| Minimum duration to ensure initialization | tPWD | 300 | us | 55 | |||
| Write Inhibit Voltage | VWI | 2 | 2.4 | V | 55 |
CAD (KiCad official)
- Symbol:
MX35LF4G24AD-Z4I - Footprint:
Package_SON:WSON-8-1EP_8x6mm_P1.27mm_EP3.4x4.3mm - 3D model: WSON-8(6x8), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.75 mm nominal WSON height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files:
mx35lf4g24ad-z4i-etched.step/mx35lf4g24ad-z4i-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mx35lf4g24ad-z4i.step/mx35lf4g24ad-z4i.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: MXIC(Macronix) datasheet (65 pp, sha256
94c96deab0c16fbf, retrieved 2026-10-26, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).