3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLM536013QDSXRQ1
Texas Instruments · DC-DC Converters · WSON-10-EP(3x3)
LM536013QDSXRQ1 from Texas Instruments, in a WSON-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | power_out | Regulator switch node that connects to the output inductor; the absolute maximum SW to GND range is -0.3 V to VIN+0.3 V. |
| 2 | BOOT | input | High-side gate driver upper supply rail that takes a 100-nF capacitor from SW to BOOT, which an internal diode charges while SW is low; the BOOT to SW absolute maximum is 3.6 V. |
| 3 | VCC | power_out | Internal 3-V regulator output that supplies the internal control circuits; connect a high-quality 1.0-µF capacitor from this pin to AGND for the fixed versions. |
| 4 | FB | power_in | In the fixed version, this pin is the output-voltage feedback and the power source for the VCC regulator, so it connects to the output node with a 10-nF bypass capacitor placed immediately adjacent; FB to GND is rated -0.3 V to 16 V for the 3.3-V version. |
| 5 | AGND | power_in | Fixed-version ground to which the input signals and FB are compared. |
| 6 | RESET | output | Open-drain reset output that needs a current-limiting pull-up to a suitable supply, reading high when the regulator is OK and low on a fault or when EN is low; RESET to GND is rated -0.3 V to 8 V with a maximum sink current of 8 mA. |
| 7 | EN | input | Enable input where high turns the regulator on and low turns it off; it can be tied to VIN, must not float, and EN to GND is rated -0.3 V to 42 V. |
| 8 | VIN | power_in | Input supply to the regulator, with input bypass capacitors connected directly between this pin and GND; VIN to GND is rated -0.3 V to 42 V absolute maximum and the recommended input range after startup is 3.8 V to 36 V. |
| 9 | SYNC/MODE | input | Multifunction mode control input tolerant of voltages up to the input voltage: a valid sync clock forces PWM and synchronizes on its rising edge, tying it high forces PWM at the internal clock, and tying it low selects AUTO mode with diode emulation at light load; it must not float. |
| 10 | GND | power_in | Power ground pin that must be bypassed to VIN immediately adjacent to this pin. |
| 11 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WSON-10-EP(3x3) |
| Category | Power Supply Chip |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN to GND | -0.3 | 42 | V | 5 | |||
| SW to GND | -0.3 | V | 5 | ||||
| BOOT to SW | -0.3 | 3.6 | V | 5 | |||
| EN to GND | -0.3 | 42 | V | 5 | |||
| FB to GND, 3.3 V fixed version | -0.3 | 16 | V | 5 | |||
| RESET to GND | -0.3 | 8 | V | 5 | |||
| RESET sink current | 8 | mA | 5 | ||||
| SYNC/MODE to GND | -0.3 | 42 | V | 5 | |||
| VCC | -0.3 | 3.6 | V | 5 | |||
| GND to AGND (fixed version only) | -1 | 2 | V | Voltage durations of 1 µs or less | 5 | ||
| Storage temperature | Tstg | -40 | 150 | °C | 5 | ||
| Input voltage range after startup | 3.8 | 36 | V | After startup | 5 | ||
| Output voltage range, 3.3 V option | 0 | 3.63 | V | 5 | |||
| Load current range, LM53601-Q1 | 0 | 1000 | mA | 5 | |||
| Operating junction temperature | -40 | 150 | °C | 5 | |||
| Initial output voltage accuracy | VFB | -1 | 1 | % | Vin = 3.8 V to 36 V, Tj = 25°C, Open Loop | 6 | |
| Initial output voltage accuracy | VFB | -1.5 | 1.5 | % | Vin = 3.8 V to 36 V, Open Loop | 6 | |
| Operating quiescent current, measured at VIN pin | IQ | 6.5 | µA | Vin = 13.5 V, Not switching, Vbias = 5 V | 6 | ||
| Bias current into FB pin (fixed versions) | IB | 46 | 80 | µA | Vin = 13.5 V, Not switching, Vbias = 5 V, Mode = 0 V | 6 | |
| Shutdown quiescent current, measured at VIN pin | ISD | 1.8 | µA | EN = 0, VIN = 13.5 V, Tj = 25°C | 6 | ||
| Minimum input voltage to operate (UVLO rising) | Vin_UVLO | 3.2 | 3.6 | 3.75 | V | Rising | 6 |
| RESET upper threshold voltage | Vreset_OV | 105 | 106.5 | 110 | % | Rising, % of Vout | 6 |
| RESET lower threshold voltage | Vreset_UV | 92 | 94 | 97 | % | Falling, % Vout | 6 |
| Magnitude of RESET lower threshold difference from steady state output voltage | Vreset_guard | 3.9 | % | Steady state output voltage and RESET threshold read at the same TJ, and VIN | 6 | ||
| Minimum input voltage for proper RESET function | Vreset_valid | 1.5 | V | 50 µA pull-up to RESET pin, EN = 0 V, Tj = 25°C | 6 | ||
| Low level RESET function output voltage | VOL | 0.4 | V | 50 µA pull-up to RESET pin, Vin = 1.5 V, EN = 0 V, Tj = 25°C | 6 | ||
| Switching frequency, without spread spectrum | Fsw | 1.89 | 2.1 | 2.4 | MHz | VIN = 13.5 V, Without spread spectrum, PWM operation | 7 |
| Switching frequency at high input voltage, 3.3 V fixed output | Fsw | 1 | MHz | VIN = 36 V, 3.3-V fixed output device and adjustable devices regardless of output voltage | 7 | ||
| Sync frequency range | FSYNC | 1.9 | 2.1 | 2.3 | MHz | Output setting + 1 V < VIN < 18 V | 7 |
| Sync input duty cycle range | DSYNC | 25 | 75 | % | High state input < 5.5 V and > 2.3 V | 7 | |
| SYNC/MODE input high threshold (MODE = FPWM) | VSYNC/MODE | 1.5 | V | 7 | |||
| SYNC/MODE input low threshold (MODE = AUTO with diode emulation) | VSYNC/MODE | 0.4 | V | 7 | |||
| SYNC/MODE leakage current | ISYNC/MODE | 1 | µA | Vin = 13.5 V, VSYNC/MODE = 3.3 V | 7 | ||
| Mode change transition time to FPWM mode | tMODE | 100 | µs | 20 mA load, VIN = 13.5 V | 7 | ||
| High side switch current limit (LM53601-Q1) | IL_HS | 1.5 | 1.83 | 2.1 | A | Duty cycle approaches 0% | 7 |
| Low side switch current limit (LM53601-Q1) | IL_LS | 1 | 1.2 | 1.43 | A | 7 | |
| Zero-cross current limit | IL_ZC | -0.01 | A | MODE/SYNC = Low | 7 | ||
| Negative current limit (LM53601-Q1) | IL_NEG | -0.7 | A | MODE/SYNC = High | 7 | ||
| High side MOSFET Rdson | Rdson | 220 | mΩ | 7 | |||
| Low side MOSFET Rdson | Rdson | 200 | mΩ | 7 | |||
| Enable input threshold voltage, rising | VEN | 1.7 | 2 | V | Enable rising | 7 | |
| Enable threshold hysteresis | VEN_HYST | 0.4 | 0.55 | V | 7 | ||
| Enable pin input current | IEN | 2.7 | µA | VIN = VEN = 13.5 V | 7 | ||
| Internal Vcc voltage | Vcc | 3.05 | V | VIN = 13.5 V, Vbias = 0 V | 7 | ||
| Internal Vcc input under voltage lock-out | Vcc_UVLO | 2.7 | V | VCC rising | 7 | ||
| Rdson of RESET output | RRESET | 50 | 120 | Ω | 8 | ||
| Thermal shutdown rising threshold | TSD | 151 | 167 | 185 | °C | 8 | |
| Maximum switch duty cycle | Dmax | 76 | % | Fsw = 2.1 MHz | 8 | ||
| Minimum input voltage for full functionality at 500-mA load, after start-up | Vin_min | 3.55 | V | VOUT = 3.3 V | 8 | ||
| Minimum input voltage for full functionality at 100% of max rated load, after start-up | Vin_min | 3.8 | V | VOUT = 3.3 V | 8 | ||
| Output voltage for 3.3-V option | Vout_3_3V | 3.23 | 3.3 | 3.37 | V | VIN = 4.0 V to 36 V, IOUT = maximum recommended load current | 8 |
| Minimum input to output voltage differential to maintain regulation accuracy, without inductor DCR drop | VDROP1 | 0.6 | V | VOUT = 3.3 V, IOUT = 1000 mA, +2/-3% output accuracy | 8 | ||
| Minimum switch on time | ton | 50 | 80.5 | ns | VIN = 18 V, IOUT = 500 mA | 9 | |
| Minimum switch off time | toff | 90 | 125 | ns | IOUT = 500 mA | 9 | |
| Delay time to RESET high signal | treset_act | 4 | 6 | 8 | ms | 9 | |
| Soft-start time | tSS | 1.3 | 3 | 4.5 | ms | Time from first SW node pulse to Vref at 90%, VIN ≥ 4.2 V | 9 |
| Input current to VIN node of DC/DC using the device | IQ_VIN | 23 | µA | VIN = 13.5 V, VOUT = 3.3 V, IOUT = 0 A | 8 | ||
| Junction-to-ambient thermal resistance | RθJA | 46.2 | °C/W | 6 | |||
| Junction-to-board thermal resistance | RθJB | 20.9 | °C/W | 6 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 4.1 | °C/W | 6 |
CAD (KiCad official)
- Symbol:
LM536013QDSXRQ1 - Footprint:
Package_SON:VSON-10-1EP_3x3mm_P0.5mm_EP1.2x2mm - 3D model: WSON-10-EP(3x3), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.75 mm tall, datasheet A, midpoint of min and max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
lm536013qdsxrq1-etched.step/lm536013qdsxrq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm536013qdsxrq1.step/lm536013qdsxrq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (51 pp, sha256
e5b0cd2ded2271f2, retrieved 2026-11-12, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).