Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

F280036PMRQ1

Texas Instruments · Microcontrollers (MCU/MPU/SOC) · LQFP-64(10x10)

F280036PMRQ1 from Texas Instruments, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 GPIO29 bidirectional General-purpose I/O referenced to VDDIO (3.3 V) with alternates SCIA_TX, EPWM7_B, EQEP1_B, LINA_RX, I2CB_SCL, HIC_NCS and AUXCLKIN.
2 GPIO28 bidirectional General-purpose I/O referenced to VDDIO (3.3 V) with alternates SCIA_RX, EPWM7_A, EQEP1_A, LINA_TX, I2CB_SDA and ERRORSTS, which requires an external pull-down.
3 XRSn bidirectional Open-drain device reset input and watchdog reset output with internal pull-up; it needs a 2.2 kΩ to 10 kΩ resistor to VDDIO and at most 100 nF to VSS, and is driven low for 512 OSCCLK cycles on a watchdog reset.
4 VDD power_in 1.2 V digital logic supply (recommended 1.14 V to 1.32 V), decoupled per the PMM section.
5 VSS power_in Digital ground, to be connected to the board ground.
6 A6 input ADC-A analog input 6 (also CMPSS-1 input and AIO228); keep the input below VDDA + 0.3 V.
7 B2,C6 input ADC-B input 2 / ADC-C input 6 (also CMPSS-3 input and AIO226); keep the input below VDDA + 0.3 V.
8 A3,B3,C5,VDAC input ADC-A input 3, ADC-B input 3, ADC-C input 5, and optional external reference for the on-chip DAC; at least 1 µF is required on VDAC if used as a DAC reference.
9 A2,B6,C9 input ADC-A input 2 / ADC-B input 6 / ADC-C input 9 (also CMPSS-1 input and AIO224); keep the input below VDDA + 0.3 V.
10 A15,B9,C7 input ADC-A input 15 / ADC-B input 9 / ADC-C input 7 (also CMPSS-1 input); keep the input below VDDA + 0.3 V.
11 A14,B14,C4 input ADC-A input 14 / ADC-B input 14 / ADC-C input 4 (also CMPSS-3 input and AIO239); keep the input below VDDA + 0.3 V.
12 A11,B10,C0 input ADC-A input 11 / ADC-B input 10 / ADC-C input 0 (also CMPSS-1 input and AIO237); keep the input below VDDA + 0.3 V.
13 A5,B12,C2 input ADC-A input 5 / ADC-B input 12 / ADC-C input 2 (also CMPSS-2/3 inputs and AIO244); keep the input below VDDA + 0.3 V.
14 A1,B7,DACB_OUT input ADC-A input 1 / ADC-B input 7 (also CMPSS-1 input); this pin is also the buffered DAC-B output, so the ADC use and DAC use are mutually exclusive in practice.
15 A0,B15,C15,DACA_OUT input ADC-A input 0 / ADC-B input 15 / ADC-C input 15 (also CMPSS-3 input); this pin is also the buffered DAC-A output.
16 VREFHI input ADC high reference: driven externally (2.4 V to VDDA) or generated internally (1.65 V or 2.5 V), with at least 2.2 µF placed between VREFHI and VREFLO.
17 VREFLO input ADC low reference, connected to analog ground VSSA.
18 A12,C1 input ADC-A input 12 / ADC-C input 1 (also CMPSS-2/4 inputs and AIO238/AIO248); keep the input below VDDA + 0.3 V.
19 A7,C3 input ADC-A input 7 / ADC-C input 3 (also CMPSS-4 input and AIO245); keep the input below VDDA + 0.3 V.
20 A8,B0,C11 input ADC-A input 8 / ADC-B input 0 / ADC-C input 11 (also CMPSS-2/4 inputs and AIO241); keep the input below VDDA + 0.3 V.
21 VSSA power_in Analog ground for the ADC, comparator and DAC blocks.
22 VDDA power_in 3.3 V analog supply; place at least 2.2 µF decoupling on this pin.
23 A4,B8,C14 input ADC-A input 4 / ADC-B input 8 / ADC-C input 14 (also CMPSS-2/4 inputs and AIO225); keep the input below VDDA + 0.3 V.
24 A9,B4,C8 input ADC-A input 9 / ADC-B input 4 / ADC-C input 8 (also CMPSS-2/4 inputs and AIO227/AIO236); keep the input below VDDA + 0.3 V.
25 A10,B1,C10 input ADC-A input 10 / ADC-B input 1 / ADC-C input 10 (also CMPSS-2 inputs and AIO230); keep the input below VDDA + 0.3 V.
26 VSS power_in Digital ground, to be connected to the board ground.
27 VDD power_in 1.2 V digital logic supply (recommended 1.14 V to 1.32 V).
28 VDDIO power_in 3.3 V digital I/O supply (2.8 V to 3.63 V, 3.3 V nominal).
29 GPIO13 bidirectional General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM7_B, MCAN_TX, SCIB_RX, PMBUSA_ALERT, SPIA_SOMI and HIC_D5.
30 GPIO12 bidirectional General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM7_A, MCAN_RX, SCIB_TX, PMBUSA_CTL, SPIA_CLK and HIC_INT.
31 GPIO11 bidirectional General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM6_B, EQEP1_B, SCIB_RX, SPIA_STE, LINB_RX and HIC_NBE0.
32 GPIO33 bidirectional General-purpose I/O referenced to VDDIO (3.3 V) with alternates I2CA_SCL, SPIB_STE, LINA_RX, SD1_C2, ADCSOCAO and HIC_D0.
33 GPIO16 bidirectional General-purpose I/O referenced to VDDIO (3.3 V) with alternates SPIA_SIMO, EPWM5_A, SCIA_TX, SD1_D1, XCLKOUT and SPIB_SOMI.
34 GPIO17 bidirectional General-purpose I/O referenced to VDDIO (3.3 V) with alternates SPIA_SOMI, EPWM5_B, SCIA_RX, SD1_C1, CANA_TX and PMBUSA_SDA.
35 GPIO24 bidirectional General-purpose I/O referenced to VDDIO (3.3 V) with alternates OUTPUTXBAR1, EQEP2_A, EPWM8_A, SPIB_SIMO, SCIA_TX and ERRORSTS, which requires an external pull-down.
36 TCK input JTAG test clock with internal pull-up enabled.
37 GPIO37/TDO output JTAG test data output (default function) that is tri-stated when no JTAG activity occurs, so an internal pull-up or external pull-up should be fitted; the pin can be used as GPIO37 in cJTAG mode.
38 TMS bidirectional JTAG test mode select with internal pull-up; a 2.2 kΩ external pull-up to VDDIO is recommended and the device has no TRSTn pin.
39 GPIO35/TDI input JTAG test data input (default function) with internal pull-up disabled by default, so an internal or external pull-up is required when used as TDI; it can be used as GPIO35 in cJTAG mode.
40 GPIO32 bidirectional General-purpose I/O referenced to VDDIO (3.3 V) with alternates I2CA_SDA, SPIB_CLK, EPWM8_B, LINA_TX, SD1_D2, CANA_TX and HIC_INT.
41 GPIO18/X2 bidirectional General-purpose I/O (GPIO18) or crystal oscillator output X2 when the XTAL is enabled; the XTAL and GPIO functions are mutually exclusive.
42 GPIO19/X1 bidirectional General-purpose I/O (GPIO19) or crystal/single-ended clock input X1; the XTAL must be configured by initialization software before enabling the oscillator.
43 VDDIO power_in 3.3 V digital I/O supply (2.8 V to 3.63 V).
44 VDD power_in 1.2 V digital logic supply (recommended 1.14 V to 1.32 V).
45 VSS power_in Digital ground, to be connected to the board ground.
46 VREGENZ input Internal regulator enable with internal pull-down: tie low to VSS to enable the internal 1.2 V VREG, or tie high to VDDIO to supply VDD externally.
47 GPIO8 bidirectional General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM5_A, ADCSOCAO, EQEP1_STROBE, SCIA_TX, SPIA_SIMO, I2CA_SCL and HIC_A0.
48 GPIO4 bidirectional General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM3_A, MCAN_TX, OUTPUTXBAR3, CANA_TX, SPIB_CLK and EQEP2_STROBE.
49 GPIO3 bidirectional General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM2_B, OUTPUTXBAR2, PMBUSA_SCL, SPIA_CLK, SCIA_RX and I2CB_SCL.
50 GPIO2 bidirectional General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM2_A, OUTPUTXBAR1, PMBUSA_SDA, SPIA_SIMO, SCIA_TX and I2CB_SDA.
51 GPIO1 bidirectional General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM1_B, I2CA_SCL, SPIA_SOMI, MCAN_TX and CLB_OUTPUTXBAR7.
52 GPIO0 bidirectional General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM1_A, I2CA_SDA, SPIA_STE, MCAN_RX and EQEP1_INDEX.
53 GPIO40 bidirectional General-purpose I/O referenced to VDDIO (3.3 V) with alternates SPIB_SIMO, EPWM2_B, PMBUSA_SDA, SCIB_TX, EQEP1_A and LINB_TX.
54 GPIO23 bidirectional General-purpose I/O referenced to VDDIO (3.3 V) with alternates EQEP1_INDEX, SCIB_RX, SPIB_STE, SD1_C4, LINA_RX and EPWM4_B.
55 GPIO41 bidirectional General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM2_A, PMBUSA_SCL, FSIRXA_D1, SCIB_RX, EQEP1_B and SPIB_SOMI.
56 GPIO22 bidirectional General-purpose I/O referenced to VDDIO (3.3 V) with alternates EQEP1_STROBE, SCIB_TX, SPIB_CLK, SD1_D4, LINA_TX and EPWM4_A.
57 GPIO7 bidirectional General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM4_B, OUTPUTXBAR5, EQEP1_B, SPIB_SIMO, FSITXA_CLK and HIC_A6.
58 VSS power_in Digital ground, to be connected to the board ground.
59 VDD power_in 1.2 V digital logic supply (recommended 1.14 V to 1.32 V).
60 VDDIO power_in 3.3 V digital I/O supply (2.8 V to 3.63 V).
61 GPIO5 bidirectional General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM3_B, OUTPUTXBAR3, MCAN_RX, CANA_RX, SPIA_STE and FSITXA_D1.
62 GPIO9 bidirectional General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM5_B, SCIB_TX, OUTPUTXBAR6, EQEP1_INDEX, SCIA_RX and I2CB_SCL.
63 GPIO10 bidirectional General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM6_A, ADCSOCBO, EQEP1_A, SCIB_TX, SPIA_SOMI and I2CA_SDA.
64 GPIO6 bidirectional General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM4_A, OUTPUTXBAR4, SYNCOUT, EQEP1_A, SPIB_SOMI and FSITXA_D0.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package LQFP-64(10x10)
Category Embedded Processors & Controllers
Pins 64

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Low-level output voltage VOL 0.4 V IOL = IOL max 71
Low-level output voltage VOL 0.2 V IOL = 100 µA 71
High-level output source current, all output pins IOH -4 mA 71
Low-level output sink current, all output pins IOL 4 mA 71
High-level output impedance, all output pins ROH 50 66 96 Ω VOH = VDDIO-0.4V 71
Low-level output impedance, all output pins ROL 48 60 84 Ω VOL = 0.4V 71
High-level input voltage VIH 2 V 71
Low-level input voltage VIL 0.8 V 71
Weak pulldown resistance RPULLDOWN 22 31 62 kΩ 71
Weak pullup resistance RPULLUP 19 30 54 kΩ 71
Internal regulator output VVREG 1.14 1.2 1.32 V 83
VDDIO supply ramp-up rate SRVDDIO-UP 8 100 mV/μs 83
VDDIO supply ramp-down rate SRVDDIO-DN 20 100 mV/μs 83
VDD (1.2V rail) supply ramp-up rate SRVDD-UP 3.5 100 mV/μs External VREG 83
VDD (1.2V rail) supply ramp-down rate SRVDD-DN 10 100 mV/μs External VREG 83
INTOSC1/INTOSC2 frequency fINTOSC 9.82 10 10.1 MHz -40℃ to 125℃ 100
INTOSC1/INTOSC2 frequency fINTOSC 9.86 10 10.1 MHz -30℃ to 90℃ 100
INTOSC1/INTOSC2 frequency fINTOSC 9.9 10 10.1 MHz -10℃ to 85℃ 100
Crystal load capacitance CL1, CL2 12 24 pF 98
Crystal shunt capacitance C0 7 pF 98
PMBus low-level input voltage VIL 0.8 V 171
PMBus high-level input voltage VIH 2.1 V 171
PMBus low-level output voltage VOL 0.4 V Ipullup = 4mA 171
Suppressed spike pulse width (input filter) tSP 0 50 ns 171
Input leakage current per pin (PMBus) Ii -10 10 µA 0.1Vbus < Vi < 0.9Vbus 171
SCL clock frequency, fast mode fSCL 10 400 kHz 171
SCL clock frequency, standard mode fSCL 10 100 kHz 172
SDA and SCL rise time, fast mode tr 20 300 ns 5% to 95% 171
SDA and SCL fall time, fast mode tf 20 300 ns 95% to 5% 171
CMPSS comparator input-referred offset -20 20 mV Low common mode, inverting input set at 50mV 141
CMPSS DAC static offset error -25 25 mV 142
CMPSS DAC static gain error -2 2 FSR 百分比 142
CMPSS DAC static INL -16 16 LSB corrected endpoints 142
CMPSS DAC static DNL -1 4 LSB corrected endpoints 142
CMPSS DAC output interference error -100 100 LSB 142
VDAC reference load VDAC 6 8 10 kΩ When VDAC is used as reference 142
Buffered DAC midpoint offset error -10 10 mV Midpoint 146
Buffered DAC gain error -2.5 2.5 FSR 百分比 146
Buffered DAC DNL -1 1 LSB corrected endpoints 146
Buffered DAC INL -5 5 LSB corrected endpoints 146
Buffered DAC load regulation -1 1 mV/V 146
Buffered DAC reference input resistance VDAC or VREFHI 160 200 240 kΩ VDAC or VREFHI 146
Buffered DAC valid output voltage range VOUT 0.3 V RL = 5kΩ 146
Buffered DAC valid output voltage range VOUT 0.6 V RL = 1kΩ 146

CAD (KiCad official)

  • Symbol: F280036PMRQ1
  • Footprint: Package_QFP:LQFP-64_10x10mm_P0.5mm
  • 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
  • 3D model files: f280036pmrq1-etched.step / f280036pmrq1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); f280036pmrq1.step / f280036pmrq1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (285 pp, sha256 4385cb7a74ef5d7f, retrieved 2026-11-13, tier: manufacturer)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF