component
DS8571-12S5
Public Made by Adomby adom
DSTECH Voltage Regulators - Linear, Low Drop Out (LDO) Regulators, SOT-23-5. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownDS8571-12S5
DSTECH · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · SOT-23-5
DS8571-12S5 from DSTECH, in a SOT-23-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Input of supply voltage, operating range 2.3 V to 6 V; the absolute maximum rating for VIN to GND is -0.3 V to 7 V. |
| 2 | GND | power_in | Ground reference pin; connect the input and output capacitor grounds back to this pin with as wide and short a copper trace as practical. |
| 3 | EN | input | Enable control input; pulling it low selects shutdown mode (100 nA typical shutdown current), with EN rising threshold VIH 1.0 V and falling threshold VIL 0.4 V, and EN rated -0.3 V to 6 V to GND. |
| 4 | NC | unconnected | No internal connection on the DS8571 SOT-23-5 version; the SNS sense function is only on the separate DS8571N variant. |
| 5 | VOUT | power_out | Output of the regulator, current-limited to 550 mA typical, and rated -0.3 V to 6 V to GND; the output can be shorted to ground indefinitely without damage. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | DSTECH |
| Package | SOT-23-5 |
| Category | Power Management (PMIC) |
| Pins | 5 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VIN | 2.3 | 6 | V | 7 | ||
| DC Output Voltage Accuracy | -2 | 2 | % | ILOAD =0.1mA | 7 | ||
| Dropout Voltage (VOUT = 1.2V) | VDROP_1.2V | 0.15 | V | ILOAD =100mA; VOUT = 1.2V | 7 | ||
| Output Current Limit | ILIM | 301 | 550 | mA | VOUT = 0V | 7 | |
| Ground Current | IQ | 30 | μA | ILOAD = 0mA | 7 | ||
| Shutdown Ground Current | ISD | 0.1 | 0.5 | μA | VEN = 0V, VOUT = 0V | 7 | |
| Enable Threshold Voltage (EN Rising) | VIH | 1 | V | EN Rising | 7 | ||
| Enable Threshold Voltage (EN Falling) | VIL | 0.4 | V | EN Falling | 7 | ||
| EN Input Current | IEN | 10 | 100 | nA | VEN = 5V | 7 | |
| Line Regulation | ΔLINE | 0.3 | % | ILOAD =30mA, 2.5V ≤ VIN ≤ 5.5V or (VOUT + 0.2V) ≤ VIN ≤ 5.5V | 7 | ||
| Load Line | ΔLOAD | 20 | mV | 1mA ≤ ILOAD ≤ 300mA | 7 | ||
| Thermal Shutdown Temperature | TSD | 160 | °C | ILOAD =10mA | 7 | ||
| Thermal Shutdown Hysteresis | ΔTSD | 20 | °C | 7 | |||
| Discharge Resistance | RDC | 30 | Ω | EN = 0V, VOUT = 0.1V | 7 | ||
| VIN to GND | VIN | -0.3 | 7 | V | 6 | ||
| VOUT, EN to GND | VOUT, EN | -0.3 | 6 | V | to GND | 6 | |
| VOUT to VIN | VOUT-VIN | -6 | 0.3 | V | 6 | ||
| Lead Temperature (Soldering) | 260 | °C | Soldering, 10 sec. | 6 | |||
| Junction Temperature | 150 | °C | 6 | ||||
| Storage Temperature Range | -60 | 150 | °C | 6 | |||
| ESD HBM | HBM | 2 | KV | 6 | |||
| ESD MM | MM | 200 | V | 6 | |||
| ESD CDM | CDM | 2 | KV | 6 | |||
| Input Voltage | VIN | 2.3 | 6 | V | 6 | ||
| Junction Temperature Range | TJ | -40 | 125 | °C | 6 | ||
| Ambient Temperature Range | TA | -40 | 85 | °C | 6 | ||
| Thermal Resistance Junction-to-Ambient (SOT-23-5) | θJA | 220 | °C/W | TA=25°C, DSTECH EVB board (Note 2) | 6 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | must be back to the DS8571 ground pin using as wide and as short of a copper trace as is practical. | 12 |
CAD (KiCad official)
- Symbol:
DS8571-12S5 - Footprint:
Package_TO_SOT_SMD:SOT-23-5 - 3D model: SOT-23-5 (KiCad packages3D, STEP)
- 3D model files:
ds8571-12s5-etched.step/ds8571-12s5-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ds8571-12s5.step/ds8571-12s5.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: DSTECH datasheet (18 pp, sha256
481282d70f89eeec, retrieved 2026-10-18, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).