Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

FT4232HPQ-TRAY

FTDI · USB ICs · QFN-68(8x8)

FT4232HPQ-TRAY from FTDI, in a QFN-68(8x8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 EECLK output Clock signal to the EEPROM; tri-state during device reset, and outputs the EEPROM clock when not in reset.
2 EEDATA bidirectional EEPROM data I/O; connect directly to EEPROM Data-In and to Data-Out via a 2.2K resistor, pull Data-Out to VCC via 10K, tri-state during device reset.
3 TEST input IC test pin that should be connected to GND for normal operation.
4 RESET# input Active-low reset input; tie to VCCIO (+3.3V) if not used.
5 GPIO3 bidirectional GPIO3 pin whose default function is an input with weak pull-down.
6 ADBUS0 bidirectional Channel A bit 0: TXD in UART mode, D0 in bit-bang mode, TCK/SK in MPSSE mode.
7 ADBUS1 bidirectional Channel A bit 1: RXD in UART mode, D1 in bit-bang mode, TDI/DO in MPSSE mode.
8 VCORE power_in +1.2V core supply voltage input; connect to VREGOUT when using the internal regulator.
9 GND power_in Ground.
10 VCCIO power_in +3.3V I/O interface power supply input; all VCCIO pins must be connected or the device will fail.
11 ADBUS2 bidirectional Channel A bit 2: RTS# in UART mode, D2 in bit-bang mode, TDO/DI in MPSSE mode.
12 ADBUS3 bidirectional Channel A bit 3: CTS# in UART mode, D3 in bit-bang mode, TMS/CS in MPSSE mode.
13 ADBUS4 bidirectional Channel A bit 4: DTR# in UART mode, D4 in bit-bang mode, GPIOL0 in MPSSE mode.
14 ADBUS5 bidirectional Channel A bit 5: DSR# in UART mode, D5 in bit-bang mode, GPIOL1 in MPSSE mode.
15 ADBUS6 bidirectional Channel A bit 6: DCD# in UART mode, D6 in bit-bang mode, GPIOL2 in MPSSE mode.
16 ADBUS7 bidirectional Channel A bit 7: RI# or TXDEN (EEPROM selectable, default RI#) in UART mode, D7 in bit-bang mode, GPIOL3 in MPSSE mode.
17 BDBUS0 bidirectional Channel B bit 0: TXD in UART mode, D0 in bit-bang mode, TCK/SK in MPSSE mode.
18 BDBUS1 bidirectional Channel B bit 1: RXD in UART mode, D1 in bit-bang mode, TDI/DO in MPSSE mode.
19 BDBUS2 bidirectional Channel B bit 2: RTS# in UART mode, D2 in bit-bang mode, TDO/DI in MPSSE mode.
20 BDBUS3 bidirectional Channel B bit 3: CTS# in UART mode, D3 in bit-bang mode, TMS/CS in MPSSE mode.
21 BDBUS4 bidirectional Channel B bit 4: DTR# in UART mode, D4 in bit-bang mode, GPIOL0 in MPSSE mode.
22 BDBUS5 bidirectional Channel B bit 5: DSR# in UART mode, D5 in bit-bang mode, GPIOL1 in MPSSE mode.
23 BDBUS6 bidirectional Channel B bit 6: DCD# in UART mode, D6 in bit-bang mode, GPIOL2 in MPSSE mode.
24 BDBUS7 bidirectional Channel B bit 7: RI# or TXDEN (EEPROM selectable, default RI#) in UART mode, D7 in bit-bang mode, GPIOL3 in MPSSE mode.
25 VCORE power_in +1.2V core supply voltage input; connect to VREGOUT when using the internal regulator.
26 VCCIO power_in +3.3V I/O interface power supply input; all VCCIO pins must be connected or the device will fail.
27 OSCI input Oscillator input; a 12 MHz crystal is connected to OSCI and OSCO.
28 OSCO output Oscillator output; a 12 MHz crystal is connected to OSCI and OSCO.
29 GND power_in Ground.
30 VREGIN power_in +3.3V input to the integrated 1.2V voltage regulator.
31 VREGOUT power_out +1.2V integrated regulator output; connect to VCORE with a 3.3uF filter capacitor and do not use to power other circuits.
32 FSOURCE power_in FSOURCE input pin for EFUSE; leave floating for normal operation.
33 VPP power_in VPP input pin for EFUSE; leave floating for normal operation.
34 CDBUS0 bidirectional Channel C bit 0: TXD in UART mode or D0 in bit-bang mode.
35 CDBUS1 bidirectional Channel C bit 1: RXD in UART mode or D1 in bit-bang mode.
36 CDBUS2 bidirectional Channel C bit 2: RTS# in UART mode or D2 in bit-bang mode.
37 CDBUS3 bidirectional Channel C bit 3: CTS# in UART mode or D3 in bit-bang mode.
38 CDBUS4 bidirectional Channel C bit 4: DTR# in UART mode or D4 in bit-bang mode.
39 VCCIO power_in +3.3V I/O interface power supply input; all VCCIO pins must be connected or the device will fail.
40 CDBUS5 bidirectional Channel C bit 5: DSR# in UART mode or D5 in bit-bang mode.
41 CDBUS6 bidirectional Channel C bit 6: DCD# in UART mode or D6 in bit-bang mode.
42 CDBUS7 bidirectional Channel C bit 7: RI# or TXDEN (EEPROM selectable, default RI#) in UART mode, or D7 in bit-bang mode.
43 SUSPEND# output Active-low output that is low when USB is in suspend mode.
44 VCORE power_in +1.2V core supply voltage input; connect to VREGOUT when using the internal regulator.
45 DDBUS0 bidirectional Channel D bit 0: TXD in UART mode or D0 in bit-bang mode.
46 DDBUS1 bidirectional Channel D bit 1: RXD in UART mode or D1 in bit-bang mode.
47 DDBUS2 bidirectional Channel D bit 2: RTS# in UART mode or D2 in bit-bang mode.
48 DDBUS3 bidirectional Channel D bit 3: CTS# in UART mode or D3 in bit-bang mode.
49 DDBUS4 bidirectional Channel D bit 4: DTR# in UART mode or D4 in bit-bang mode.
50 DDBUS5 bidirectional Channel D bit 5: DSR# in UART mode or D5 in bit-bang mode.
51 VCCIO power_in +3.3V I/O interface power supply input; all VCCIO pins must be connected or the device will fail.
52 DDBUS6 bidirectional Channel D bit 6: DCD# in UART mode or D6 in bit-bang mode.
53 DDBUS7 bidirectional Channel D bit 7: RI# or TXDEN (EEPROM selectable, default RI#) in UART mode, or D7 in bit-bang mode.
54 GPIO2 bidirectional GPIO2 or I2C_INT# pin whose default function is GPIO2 input with weak pull-down.
55 GPIO1 bidirectional GPIO1 or I2C_SCL pin whose default function is GPIO1 input with weak pull-down.
56 GPIO0 bidirectional GPIO0 or I2C_SDA pin whose default function is GPIO0 input with weak pull-down.
57 VCC_USB power_in +3.3V internal USB PHY supply input that cannot be connected directly to the USB supply; a +3.3V regulator is required and LC filtering is recommended.
58 DM bidirectional USB data signal minus.
59 DP bidirectional USB data signal plus.
60 REF input Current reference input; connect via a 12K Ohm 1% resistor to GND.
61 VCC_PD power_in +3.3V internal PD PHY power supply input.
62 PD1_CC2 bidirectional Analog I/O pin for the PD1 CC2 line.
63 PD1_SVBUS input Analog input for scaled-down PD1 VBUS sensing; VBUS must be divided by 10 before this pin.
64 PD1_VCONN power_in Power input for the PD1 VCONN power source; connect to 3.3V.
65 PD1_CC1 bidirectional Analog I/O pin for the PD1 CC1 line.
66 VCORE power_in +1.2V core supply voltage input; connect to VREGOUT when using the internal regulator.
67 PWREN# output Active-low power-enable output: 0 = normal operation, 1 = USB suspend or device not configured.
68 EECS bidirectional EEPROM chip select, tri-state during device reset; pull to VCCIO via 10K if no EEPROM.
69 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer FTDI
Package QFN-68(8x8)
Category Communication Interface Chip/UART/485/232
Pins 69

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Storage Temperature -65 150 °C 27
Ambient Operating Temperature (Power Applied) -40 85 °C Power Applied 27
VCORE Supply Voltage VCORE -0.3 2 V 27
VCCIO IO Voltage VCCIO -0.3 4 V 27
DC Input Voltage, USBDP and USBDM -0.5 3.63 V 27
DC Input Voltage, High Impedance Bi-directional (powered from VCCIO) -0.3 5.8 V powered from VCCIO 27
DC Input Voltage, All Other Inputs -0.5 V max is + (VCCIO +0.5) 27
DC Output Current, Outputs 16 mA 27
VCORE VCC Core Operating Supply Voltage VCORE 1.08 1.2 1.32 V 27
VCCIO Operating Supply Voltage VCCIO 2.97 3.3 3.63 V 27
VREGIN Voltage regulator Input VREGIN 3 3.3 3.6 V 27
VREGOUT Voltage regulator Output VREGOUT 1.08 1.2 1.32 V 27
Regulator Current Ireg 21.11 150 mA VREGIN +3.3V and data transfer with 12Mbps 27
VREGIN Suspend Supply Current Icc1s 1.64 mA USB Suspend 27
VCC_USB operating supply current I_vcd_usb 22.7 mA Data transfer with 12Mbps 27
VCC_IO operating supply current I_vccio 0.87 mA Data transfer with 12Mbps 27
VCC_PD suspend supply current I_vcc_pd 209 uA PD suspend 27
Output Voltage High Voh 2.4 3.14 V Ioh = +/-2mA 28
Output Voltage High Voh 3.2 V I/O Drive strength* = 8mA 28
Output Voltage High Voh 3.22 V I/O Drive strength* = 12mA 28
Output Voltage Low Vol 0.18 0.4 V Iol = +/-2mA 28
Output Voltage Low Vol 0.12 V I/O Drive strength* = 8mA 28
Output Voltage Low Vol 0.08 V I/O Drive strength* = 12mA 28
Output Voltage Low Vol 0.07 V I/O Drive strength* = 16mA 28
Input low Switching Threshold Vil 0.8 V LVTTL 28
Input High Switching Threshold Vih 2 V LVTTL 28
Schmitt trigger negative going threshold voltage Vt- 0.8 1.1 V 28
Schmitt trigger positive going threshold voltage Vt+ 1.6 2 V 28
Input pull-up resistance Rpu 40 75 190 KΩ Vin = 0 28
Input pull-down resistance Rpd 40 75 190 KΩ Vin =VCCIO 28
Input Leakage Current Iin 15 45 85 μA Vin = 0 28
Tri-state output leakage current Ioz -10 10 μA Vin = 5.5V or 0 28
Human Body Model (HBM) -2 2 kV ANSI/ESDA/JEDEC JS-001 Class 2 28
Machine Mode (MM) -200 200 V JEDEC EIA/JESD22-A115-C, Class B 28
Charge Device Model (CDM) -500 500 V ANSI/ESDA/JEDEC JS-002, JEDEC JESD22-C101-D Class-III 28
Latch-up -200 200 mA JEDEC STANDARD EIA/JESD78, Trigger Class-II 28
TJ Junction Temperature (FT4232HPQ) TJ -40 25 125 °C FT4233HPL/FT4233HPQ/FT4232HPQ 29
ѲJA Thermal Resistance Junction-to-Ambient (FT4232HPQ) ѲJA 23.65 °C/W Preliminary data 29
ѲJC Thermal Resistance Junction-to-Case (FT4232HPQ) ѲJC 9.35 °C/W Preliminary data 29

CAD (KiCad official)

  • Symbol: FT4232HPQ-TRAY
  • Footprint: Package_DFN_QFN:QFN-68-1EP_8x8mm_P0.4mm_EP5.2x5.2mm
  • 3D model: QFN-68(8x8) (KiCad packages3D, STEP)
  • 3D model files: ft4232hpq-tray-etched.step / ft4232hpq-tray-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ft4232hpq-tray.step / ft4232hpq-tray.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: FTDI datasheet (39 pp, sha256 4394e4c473a80dcf, retrieved 2026-11-02, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF