component
CH392T
Public Made by Adomby adom
WCH Jiangsu Qin Heng Ethernet Transceivers, TSSOP-20. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownCH392T
WCH Jiangsu Qin Heng · Ethernet Transceivers · TSSOP-20
CH392T from WCH Jiangsu Qin Heng, in a TSSOP-20. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RSTI | input | External reset input, active low; when low the chip is held in reset and after release it delays about 35 ms before normal operation. |
| 2 | SEL | input | Communication interface select with internal pull-up: high selects the asynchronous UART, low selects the SPI interface, sampled at power-on reset. |
| 3 | TXD | output | Asynchronous serial data output to the host MCU. |
| 4 | RXD | input | Asynchronous serial data input from the host MCU, with internal pull-up resistor. |
| 5 | SCS | input | SPI chip select input, active low. |
| 6 | SCK | input | SPI clock input; the chip samples data on the rising edge and outputs on the falling edge (SPI mode 0 or 3). |
| 7 | SDO | output | SPI data output to the host MCU MISO line. |
| 8 | SDI | input | SPI data input from the host MCU MOSI line. |
| 9 | RXP | passive | Ethernet differential receive positive signal, connected to the magnetics/RJ45 port. |
| 10 | RXN | passive | Ethernet differential receive negative signal, connected to the magnetics/RJ45 port. |
| 11 | TXP | passive | Ethernet differential transmit positive signal, connected to the magnetics/RJ45 port. |
| 12 | TXN | passive | Ethernet differential transmit negative signal, connected to the magnetics/RJ45 port. |
| 13 | NC | unconnected | Reserved pin; leave floating (no connection). |
| 14 | VDD | power_in | 3.3 V power supply voltage input. |
| 15 | INT | output | Interrupt request output to the host MCU, active low. |
| 16 | ACT | output | Drive pin for the Ethernet activity indicator LED. |
| 17 | LINK | output | PHY link indicator drive pin, active low. |
| 18 | GND | power_in | Chip ground. |
| 19 | XI | input | Crystal oscillator input; an 8 MHz crystal is required for versions before 0x18, while 8 MHz or 16 MHz is accepted from version 0x18 onward. |
| 20 | XO | output | Crystal oscillator output (datasheet table lists this pin as output; the description text calls it the input end of the oscillator). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | WCH Jiangsu Qin Heng |
| Package | TSSOP-20 |
| Category | Interface |
| Pins | 20 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| System supply voltage | VDD | 3 | 3.3 | 3.6 | V | 23 | |
| GPIO low-level input voltage | VIL | -0.3 | 0.9 | V | 23 | ||
| GPIO high-level input voltage | VIH | 2 | V | 23 | |||
| Low-level output voltage | VOL | 0 | 0.4 | V | 23 | ||
| Operating ambient temperature | TA | -40 | 85 | ℃ | VDD=3.3V | 23 | |
| Storage ambient temperature (CH392T) | TS | -40 | 125 | ℃ | CH392T | 23 | |
| Supply voltage (VDD to GND) | VDD | -0.3 | 3.9 | V | 23 | ||
| Voltage on input or output pins | VIO | -0.3 | V | 23 | |||
| Chip default run current after power-on | Iidle | 19.4 | mA | 23 | |||
| Chip run current after network initialization | Iinit | 23.7 | mA | 23 | |||
| Chip current after network connection | Ilink | 23.5 | mA | 23 | |||
| Current during Ethernet transmission | Isend | 40 | mA | 23 | |||
| Current during Ethernet reception | Irec | 24 | mA | 23 | |||
| Current in light sleep mode 1 | Isleep1 | 4.8 | mA | 23 | |||
| Current in light sleep mode 2 | Isleep2 | 11.7 | mA | 23 | |||
| Current in light sleep mode 3 | Isleep3 | 11.7 | mA | 23 | |||
| Current in deep sleep mode | Istop | 70 | uA | 23 |
CAD (KiCad official)
- Symbol:
CH392T - Footprint:
Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm - 3D model: TSSOP-20 (KiCad packages3D, STEP)
- 3D model files:
ch392t-etched.step/ch392t-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ch392t.step/ch392t.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: WCH Jiangsu Qin Heng datasheet (28 pp, sha256
6e567c4f77a16da0, retrieved 2026-10-20, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).